Yamaha NP-S2000 Service Manual
Hide thumbs Also See for NP-S2000:

Advertisement

Note:
When the NET P.C.B. or IC506 on NET P.C.B. is replaced, the network function of this unit will not operate properly
without additional setting.
In such a case, report the serial number of this unit to the following e-mail address.
Yamaha Corporation will reply providing the setting procedure to make the network function of this unit operate
properly.
注意:
NET P.C.B. または NET P.C.B. の IC506 を交換すると本機のネットワーク機能が正常に動作しなくなり、正常動作の
ための追加設定が必要になります。
そのような場合には本機のシリアルナンバーを下記の E メールアドレスへご連絡ください。
折り返し、ネットワーク機能が正常に動作するための追加設定方法をご連絡します。
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known
and understood by the users, and have therefore not been restated.
WARNING:
IMPORTANT:
■ CONTENTS
TO SERVICE PERSONNEL ............................................2
FRONT PANELS .............................................................3
REAR PANELS ...........................................................3-4
REMOTE CONTROL PANEL ..........................................5
SPECIFICATIONS / 参考仕様 .....................................5-7
INTERNAL VIEW ............................................................8
UPDATING FIRMWARE /
ファームウェアのアップデート .............................. 14-21
ダイアグ(自己診断機能) .......................................22-36
1 0 1 2 0 4
NP-S2000
E-mail: ycav-ysiss@gmx.yamaha.com
www.electronicsrepair.net
Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
NETWORK PLAYER
SERVICE MANUAL
IMPORTANT NOTICE
DISPLAY DATA .............................................................37
IC DATA ...................................................................38-47
PRINTED CIRCUIT BOARDS .................................48-59
PIN CONNECTION DIAGRAMS ...................................60
BLOCK DIAGRAM ........................................................61
SCHEMATIC DIAGRAMS .......................................62-69
REPLACEMENT PARTS LIST ................................71-86
REMOTE CONTROL .....................................................87
ADVANCED SETUP MENU ..........................................88
拡張設定メニュー一覧 ...................................................88
P.O.Box 1, Hamamatsu, Japan
'11.01

Advertisement

Table of Contents
loading

Summary of Contents for Yamaha NP-S2000

  • Page 1: Table Of Contents

    This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known and understood by the users, and have therefore not been restated.
  • Page 2: To Service Personnel

    NP-S2000 ■ TO SERVICE PERSONNEL AC LEAKAGE WALL EQUIPMENT TESTER OR 1. Critical Components Information OUTLET UNDER TEST EQUIVALENT Components having special characteristics are marked must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only)
  • Page 3: Front Panels

    NP-S2000 ■ FRONT PANELS U, B, G, J models T model ■ REAR PANELS U model T model B model...
  • Page 4 NP-S2000 G model J model...
  • Page 5: Remote Control Panel

    NP-S2000 ■ REMOTE CONTROL PANEL ■ SPECIFICATIONS / 参考仕様 ■ Audio Section / オーディオ部 NPS2 Output Level / 出力レベル (1 kHz, 0 dB, fs 44.1 kHz) ...................2.0 ±0.3 V Signal to Noise Ratio / 信号対雑音比 (IHF-A Network) (1 kHz, 0 dB, fs 44.1 kHz) ................
  • Page 6 NP-S2000 ■ General / 総合 Power Supply / 電源電圧 TwonkyMedia is a registered trademark of PacketVideo Corporation. U model ..........AC 110–120 V, 50/60 Hz TwonkyMedia は PacketVideo Corporation の登録商標です。 T model ............AC 220 V, 50 Hz B model ............AC 230 V, 50 Hz G model ..........
  • Page 7 NP-S2000 • SET MENU TABLE / セットメニュー VALUE MAIN MENU SUB-MENU FUNCTION [INITIAL VALUE] DHCP [On] / Off NETWORK Select “On” to use the DHCP server to automatically configure the network Configuration settings of this unit or “Off” to configure manually.
  • Page 8: Internal View

    NP-S2000 ■ INTERNAL VIEW Top view POWER (3) P.C.B. NET (2) P.C.B. DAC (1) P.C.B. NET (1) P.C.B. DAC (2) P.C.B. POWER TRANSFORMER FOR AUDIO SECTION POWER TRANSFORMER FOR CONTROL SECTION POWER (2) P.C.B. POWER (1) P.C.B. POWER (4) P.C.B.
  • Page 9: Disassembly Procedures / 分解手順

    NP-S2000 ■ DISASSEMBLY PROCEDURES / 分解手順 (Remove parts in the order as numbered.) (番号順に部品を取り外してください。 ) Disconnect the power cable from the AC outlet. AC 電源コンセントから、電源コードを抜いてください。 1. Removal of Bottom Cover 1. ボトムカバーの外し方 a. Spread a rubber sheet and cloth, and place this unit a.
  • Page 10 NP-S2000 3. Removal of Top Cover 3. トップカバーの外し方 a. To prevent inside cables from being pinched, reinstall a. 内部のケーブルの挟み込みを避けるために、外した the removed 4 legs, then face the upper side of this レッグ 4 個を再び取り付けてから、本機を反転し天面 unit upward. (Fig. 2) を上にして置きます。 (Fig. 2)...
  • Page 11 NP-S2000 6. Removal of NET (1) P.C.B. 6. NET(1)P.C.B. の外し方 a. Remove 2 screws ( ⑨ ), 2 screws ( ⑩ ) and screw ( ⑪ ). a. ⑨ のネジ 2 本、⑩ のネジ 2 本、⑪のネジ1本を外し (Fig. 4) ます。 (Fig. 4)...
  • Page 12 NP-S2000 8. Removal of NET (2) P.C.B. 8. NET(2)P.C.B. の外し方 a. Remove 2 screws ( ⑰ ). (Fig. 6) a. ⑰ のネジ 2 本を外します。 (Fig. 6) b. Remove 5 screws ( ⑱ ). (Fig. 7) b. ⑱ のネジ 5 本を外します。 (Fig. 7)...
  • Page 13 NP-S2000 When checking the P.C.B.s: P.C.B. をチェックする場合には: • Put the rubber sheet and the cloth over this unit, and ・ 本機の上にゴムシートと布を敷き、その上に DAC place the DAC (1), DAC (2) and NET (1) P.C.B.s on (1) 、DAC(2) 、NET(1)P.C.B. を置きます。 (Fig. 8) them. (Fig. 8) ・...
  • Page 14: ファームウェアのアップデート

    NP-S2000 ■ UPDATING FIRMWARE / ファームウェアのアップデート When the following parts are replaced, the firmware must 下記の部品を交換した場合、ファームウェアを最新バー be updated to the latest version. ジョンにアップデートする必要があります。 Firmware to be updated / アップデートするファームウェア Replaced parts FLASH ROM firmware Sub-microprocessor firmware 交換した部品 FLASH ROM ファームウェア...
  • Page 15 NP-S2000 Updating FLASH ROM firmware FLASH ROM ファームウェアのアップデート ● Required Tools ● 必要なツール • Broadband router that supports the DHCP (Dynamic ・ DHCP (Dynamic Host Confi guration Protocol) サー Host Configuration Protocol) server function バー対応のブロードバンドルーター • Network cable: CAT-5 or higher straight cable ・...
  • Page 16 " " キー Firmware update menu ファームウェアのアップデートメニュー Power is turned on / 電源オン Setup menu / 設定メニュー YAMAHA Network Player NP-S2000 1 NETWORK Confi guration 4 Firmware Update Writing is started / 書き込み開始 Firmware Update OK? <NO Firmware Update OK? YES>...
  • Page 17 NP-S2000 Updating Sub-microprocessor firmware サブマイコンファームウェアのアップデート ● Required Tools ● 必要なツール • Firmware downloader program ・ ファームウェア書き込み用プログラム FlashSta.exe FlashSta.exe • Firmware ・ ファームウェア NPS2000_SUB_xxx.mot NPS2000_SUB_xxx.mot NPS2000_SUB_xxx.id NPS2000_SUB_xxx.id • RS-232C cross cable “D-sub 9 pin female” ・ RS-232C クロスケーブル D-sub 9 pin メス...
  • Page 18 NP-S2000 ● Connection ● 接続 Disconnect the power cable of this unit from the ※ 本機の電源コードを AC コンセントから抜いてく AC outlet ださい。 • Set the switch (SW7) of RS-232C conversion ・ RS-232C 変換アダプターのスイッチ (SW7) FLASH adaptor to the “FLASH UCOM” position. (Fig. 1) UCOM 側に設定します。...
  • Page 19 NP-S2000 ● Operation procedure ● 操作方法 1. With the power switch turned to “OFF”, connect 1. 電源スイッチを OFF にした状態で、本機の電 the power cable of this unit to the AC outlet. 源コードを AC コンセントに接続します。 The power to this unit is supplied and the sub- 本機に電源が入り、サブマイコンが書き込みモー...
  • Page 20 NP-S2000 5. Click [Setting], and set the baud rate. (Fig. 4) 5. [Setting]をクリックし、通信速度の設定を行い ます。 (Fig. 4) 115200 Fig. 4 6. Click [E.P.R.], then the “Erase” screen appears. (Fig. 5) 6. [E.P.R]をクリックすると、 「Erase」が表示されま す。 (Fig. 5) 7. Click [OK] to start writing. (Fig. 5) 7.
  • Page 21 NP-S2000 8. When writing of the firmware is completed, the 8. ファームウェアの書き込みが完了すると、以下の screen appears as shown below. (Fig. 6) 画面が表示されます。 (Fig. 6) Click [OK]. (Fig. 6) [OK]をクリックします。 (Fig. 6) 9. Click [Exit] to end FlashSta.exe. (Fig. 6) 9. [Exit] をクリックして FlashSta.exe を終了します。...
  • Page 22: Self-Diagnostic Function / ダイアグ(自己診断機能

    NP-S2000 ■ SELF-DIAGNOSTIC FUNCTION / ダイアグ(自己診断機能) This unit has self-diagnostic functions that are intended 本機には、検査、測定、不良個所の発見を目的にしたダ for inspection, measurement and location of faulty point. イアグ(自己診断機能)があります。 There are 11 main menu items, each of which has sub- ダイアグメニューは 11 個あり、そのそれぞれにサブメ menu items.
  • Page 23 Power switch Front panel display 電源スイッチ フロントパネルディスプレイ Display / 表示 Main menu display / メインメニュー表示 YAMAHA NetworkPlayer NP-S2000 1-1.FlashROM Ver.1.00 After a few seconds / 数秒後 ● Starting Self-Diagnostic Function in ● プロテクション解除モードでの起動 the protection cancel mode If the protection function works and causes hindrance to プロテクションが動作することにより、故障箇所の診断...
  • Page 24 NP-S2000 CAUTION! 注意! Using this product with the protection function disabled プロテクションを解除した状態でのダイアグモードは、 may cause further damage to this unit. Use special care 危険な状態でもプロテクションが作動しないため、動作 for this point when using this mode. させると、機器を破壊することがあります。このモード を使用する場合は十分注意してください。 ● History of protection function ● プロテクションの履歴 When the protection function has worked, its history プロテクションが働いた場合、...
  • Page 25 NP-S2000 ● Operation procedure of Main menu ● メインメニューとサブメニューの操作 and Sub-menu There are 11 main menu items, each of which has sub- ダイアグには 11 のメインメニューがあり、そのそれぞれ menu items. にサブメニューがあります。 メインメニューとサブメニューの選択 Main menu Sub-menu selection ジョグダイヤルを回して、メインメニューとサブメニュー Select both main menu and sub-menu by turning the jog の両方を選択します。...
  • Page 26 NP-S2000 ● Details of Self-Diagnostic Function ● ダイアグメニュー詳細 menu 1. VERSION/CHECKSUM 1. VERSION/CHECKSUM ファームウェアバージョン、チェックサムが表示さ The firmware version and checksum values are れます。 displayed. チェックサムは、データを 8 ビットごとに加算して The checksum is obtained by adding the data at いき、4 桁の 16 進数で表記したものです。 every 8-bit and expressing the result as a 4-figure hexadecimal notation.
  • Page 27 NP-S2000 2. DESTINATION 2. DESTINATION The destination of this unit is displayed. 本機の仕向け先が表示されます。 2-1.Destination:U U / T / G (B, G) / J models 3. DISPLAY CHECK 3. DISPLAY CHECK This menu is used to check the FL display and FL 表示とインジケーターをチェックします。...
  • Page 28 NP-S2000 4. FACTORY PRESET 4. FACTORY PRESET This menu is used to reserve/inhibit initialization of the バックアップ IC(EEPROM:NET P.C.B. の IC506)の back-up IC (EEPROM: IC506 on NET P.C.B.). 初期化を予約/禁止します。 The display is changed by pressing the “RETURN” key. RETURN キーを押すと表示が切り替わります。...
  • Page 29 NP-S2000 5-2. PRV_R 5-2. PRV_R R channel power supply protection detection R チャンネルの電源電圧プロテクションの検出 Detected: +12VR, -12VR, +5VR, +3.3VR, 検出先: +12VR、-12VR、+5VR、+3.3VR、 AC_R AC_R Detection port: 40 pin of sub-microprocessor 検出ポート: サブマイコン(DAC P.C.B. の (IC208 on DAC P.C.B.) IC208)の 40 ピン Normal value: 86 to 155 正常値:...
  • Page 30 NP-S2000 6. PROTECTION HISTORY 6. PROTECTION HISTORY This menu is used to display the history of protection プロテクション履歴が表示されます。 function. 6-1. RESET/DISPLAY 6-1. RESET/DISPLAY The display is changed by pressing the RETURN  キーを押すと表示が切り替わりま “RETURN” key. す。 Reset: The history will be initialized / 履歴消去...
  • Page 31 NP-S2000 NETWORK 7. NETWORK This menu is used to check functions related to NETWORK 関連機能をチェックします。 NETWORK. 本機の NETWORK ポートとブロードバンドルーター Connect NETWORK port of this unit and LAN port of の LAN ポートをネットワークケーブルで接続します。 broadband router with a network cable. ※ サブメニュー表示中にネットワークの状態が変わ...
  • Page 32 NP-S2000 7-4. EXT LOOPBACK TEST 7-4. EXT LOOPBACK TEST Transmission/reception of the NETWORK port NETWORK ポートの送受信テストを行います。 is checked. 電源を切った状態で、下図のように NETWORK With the power turned off, short between pins ポートのピンをショートします。 of the NETWORK port as shown in the figure ダイアグを起動して本メニューを選択します。 below.
  • Page 33 NP-S2000 7-7. LINE NOISE 100 7-7. LINE NOISE 100 サービスでは使用しません。 Not for service. 7-7.LINE NOISE 100 7-8. I2C CHECK 7-8. I2C CHECK Reading EEPROM (IC506 on NET P.C.B.) is EEPROM(NET P.C.B. の IC506) の読み出しを checked. チェックします。 7-8.I2C EEP:OK OK: No error detected 不良検出なし...
  • Page 34 NP-S2000 8. AUDIO CHECK 8. AUDIO CHECK This menu is used to check the audio signal route テスト信号を使って、DAC(DAC P.C.B. の IC6)以降 past the DAC (IC6 on DAC P.C.B.) by using the test のオーディオ信号経路をチェックします。 signal. ジョグダイヤルを回してサブメニューを選択します。 Turn the jog dial to select the sub-menu.
  • Page 35 NP-S2000 9. POWER OFF FACTOR HISTORY 9. POWER OFF FACTOR HISTORY This menu is used to display the history of power off 電源オフ要因履歴が表示されます。 factor. RETURN キーを押すと表示が切り替わります。 The display is changed by pressing the “RETURN” key . 9-1. History 1 / 履歴 1 9-1.Standbyon...
  • Page 36 NP-S2000 A. FONT TEST A. FONT TEST Not for service. サービスでは使用しません。 A-1.Font Test:0000 B. FIRMWARE UPDATE B. FIRMWARE UPDATE Not for service. サービスでは使用しません。 B-1.Firmware Update?
  • Page 37: Display Data

    NP-S2000 ■ DISPLAY DATA ● V701 : GP1264AI (DAC P.C.B.) PATTERN AREA ● PIN CONNECTION Pin No. Connection F1 NP LGND PGND LAT2 CLK2 41 42 Pin No. Connection CLK1 LAT1 PGND LGND Note : 1) F1, F2 ..Filament pin 2) NP ..
  • Page 38: Ic Data

    NP-S2000 ■ IC DATA IC208, 701: R5F21356ANFP (DAC P.C.B.) Microprocessor (Sub-microprocessor / VFD2) I/O ports Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6 Peripheral functions UART or System clock Timers clock synchronous serial I/O...
  • Page 39 NP-S2000 IC208 (Sub-microprocessor) Pin No. Port Function Name Pin No. Port Function Name P5_6 PRY_A P6_7 LED_POWER (Full) P3_2 P_DET P6_6 P6_5 NCPU_N_INT P3_0 PRY_D P4_2 AD-IN VREF P4_5 MODE MODE P1_7 P4_3 P1_6 NCPU_N_RST P4_4 P1_5 S-RX NCPU_MISO P1_4...
  • Page 40 NP-S2000 IC701 (VFD2) Pin No. Port Function Name Pin No. Port Function Name P5_6 VFD_DATA_SW P6_7 DATA0F P3_2 ADDRESS_02 P6_6 DATA0E P6_5 DATA0D P3_0 ADDRESS_00 P4_2 ADDRESS_10 P4_5 VFD_DATA_ACK MODE MODE P1_7 VFD_DATA_SW_STAT P4_3 ADDRESS_11 P1_6 S-CLK FL_CLK1 P4_4 ADDRESS_12...
  • Page 41 NP-S2000 IC702: R5F364AENFA (DAC P.C.B.) Microprocessor (VFD1) No replacement part available. / サービス部品供給なし Port P0 Port P1 Port P1 Port P3 Port P4 Port P5 VCC2 ports Internal peripheral functions System clock generator UART or clock synchronous serial I/O Timer (16-bit)
  • Page 42 NP-S2000 Pin No. Port Function Name Pin No. Port Function Name P9_6 VFD_DATA_SW P6_1 S-CLK VNP2_FL_CLK P9_5 VFD_DATA_SW_STAT P6_0 P5_7 P9_4 VFD_FIX_DISP_REQ P9_3 VFD_MUTE0 P5_6 P5_5 P9_2 P9_1 P5_4 P9_0 P5_3 BYTE BYTE P5_2 VNP2_FL_CTL CNVSS CNVSS P5_1 FL_CTL P5_0...
  • Page 43 NP-S2000 Pin No. Port Function Name P1_7 ADDRESS_07 P1_6 ADDRESS_06 P1_5 ADDRESS_05 P1_4 ADDRESS_04 P1_3 ADDRESS_03 P1_2 ADDRESS_02 P1_1 ADDRESS_01 P1_0 ADDRESS_00 P0_7 DATA07 P0_6 DATA06 P0_5 DATA05 P0_4 DATA04 P0_3 DATA03 P0_2 DATA02 P0_1 DATA01 P0_0 DATA00 P10_7 DATA0F...
  • Page 44 NP-S2000 IC504: YTD446-CZ (NET P.C.B.) Main microprocessor (Versatile network processor) No replacement part available. / サービス部品供給なし GPIO Memory I/F Interrupt ARM926EJ-S Controller Memory ARM9EJ-S Controller0 Dual Timer0 UART0 I-cache D-cache UART1 Dual Timer1 16KB 16KB Memory UART2 Watchdog Controller1 Timer...
  • Page 45 NP-S2000 Condition When Used Pin No. Port Name Function Name Detail of Function Logic nRESET VNP2_N_RST L act System reset terminal XI_S – Clock System clock crystal oscillation terminal XO_S – Clock System clock crystal oscillation terminal AE24 XI_A –...
  • Page 46 NP-S2000 Condition When Used Pin No. Port Name Function Name Detail of Function Logic nINT1 – Interrupt Empty nINT2 PHY_N_INT Interrupt Interrupt from PHY TXD0 DBG_TXD UART TX Serial for debugging RXD0 DBG_RXD UART RX Serial for debugging AGPIO[4] DBG_LED0...
  • Page 47 NP-S2000 Condition When Used Condition When Used Pin No. Port Name Function Name Detail of Function Pin No. Port Name Function Name Detail of Function Logic Logic IF data output (FLD CPU ↔ Main microprocessor) AE16 USBP USBP Data USB data +...
  • Page 48: Printed Circuit Boards

    NP-S2000 ■ PRINTED CIRCUIT BOARDS NET (1) P.C.B. NET (2) P.C.B. (Side A) (Side A) DIGITAL OUT NETWORK OPTICAL COAXIAL SYSTEM CONNECTOR (For factory) No replacement part available. to chassis サービス部品供給なし (For factory) (For factory) (For factory) CB501 CB502 CB514...
  • Page 49 NP-S2000 NET (1) P.C.B. NET (2) P.C.B. (Side B) (Side B) IC581 IC506 • Semiconductor Location Ref no. Location D5301 D5801 D5802 D5803 D5804 IC506 IC581...
  • Page 50 NP-S2000 DAC (1) P.C.B. (Side A) POWER (1) (W301) +12VL AGNDL -12VL PRV_L NET (1) (CB513) CB404 IC18 IC19 IC14 IC401 DAC (2) IC20 (CB213) PRV_D PRV_R PRV_L NCPU_MOSI NCPU_MISO NCPU_N_INT NCPU_N_RST NCPU_PON IC12 RY_UNBAL RY_BAL MGND IC402 VNP2_FL_MOSI VNP2_FL_CLK...
  • Page 51 NP-S2000 DAC (1) P.C.B. (Side B) • Semiconductor Location Ref no. Location D401 D402 D403 D404 D407 D408...
  • Page 52 NP-S2000 DAC (1) • Semiconductor Location POINT D XL201 (Pin 9 of IC208) (CB406) DAC (1) Ref no. Location Ref no. Location Ref no. Location (CB407) DBG_MISO DAC (2) P.C.B. (Side A) D201 IC203 IC701 DBG_BUSY DBG_MOSI D202 IC204 IC702...
  • Page 53 NP-S2000 DAC (2) P.C.B. (Side B) • Semiconductor Location Writing port Ref no. Location D204 D205 CB214 D701 D702 D703 D704 D715 D716 Q702 Q703 Q704 DAC (3) P.C.B. (Side B)
  • Page 54 NP-S2000 Notes) 注意) Safety measures 安全対策 • Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such ・ この製品の内部には高電圧部分があり危険です。修理の際は、絶縁性の手袋を使用するなどの安全対策を行ってください。 as wearing insulating gloves. ・ 下記のコンデンサには電源を OFF にした後も電荷が残り、高電圧が維持されており危険です。修理作業前に放電用抵抗(5 • Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a k Ω...
  • Page 55 NP-S2000 POWER (1) P.C.B. (Side B) • Semiconductor Location Ref no. Location D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D313 D314 Q301 Q302 Q303 Q304...
  • Page 56 NP-S2000 POWER (2) P.C.B. POWER (3) P.C.B. (Side A) (Side A) 5 k-ohms AC IN 10 W CB602 CB601 ACFL2 ACFL1 to chassis FLGND (B, G, J models) DAC (3) (W702) IC601 IC354 IC353 POWER TRANSFORMER for Audio section PRV_D DGND +3.3D...
  • Page 57 NP-S2000 POWER (2) P.C.B. POWER (3) P.C.B. (Side B) (Side B) • Semiconductor Location Ref no. Location Ref no. Location Ref no. Location D355 D365 D609 D357 D369 D611 D358 D601 D612 D359 D602 D613 D360 D603 D614 D361 D605...
  • Page 58 NP-S2000 POWER (4) P.C.B. POWER (5) P.C.B. POWER (6) P.C.B. (Side A) (Side A) (Side A) STANDBY/ON U, B, G, J models T model (power) Jog dial SELECT POWER ENTER PUSH indicator SW781 SW751 RO_A RO_B I_KEYC MGND MGND LED_STBY...
  • Page 59 NP-S2000 POWER (4) P.C.B. POWER (5) P.C.B. POWER (6) P.C.B. (Side B) (Side B) (Side B) • Semiconductor Location Ref no. Location D751 D752 Q771 Q772 Q773...
  • Page 60: Pin Connection Diagrams

    NP-S2000 ■ PIN CONNECTION DIAGRAMS • ICs • Diodes BD6517F-E2 CS230011-CZZR DIX9210PTR IP101ALF MX29GL128ELT2I-90G 1SS355 D4SBN20-7101 HZU3.9B1 TRF-E HZU5.1B2 TRF-E Anode Anode Anode – Cathode Cathode Cathode RS203M-B-C-J80 RSB6.8S 6.8V S1NB60 1.0A 600V UDZS3.0B 3.0V UDZS5.6B TE-17 5.6V UDZS6.2B 6.2V...
  • Page 61: Block Diagram

    NP-S2000 BLOCK DIAGRAM +12L DAC 5V +3.3L DAC 3.3V Shunt Shunt +3.3L +5L -12L EEPROM 128kbit EEP_SDA BGPIO0/I2C_SDA R1EX24016ATAS0A IC14 IC18 EEP_SCL TC74VHC157 UART0 : DEBUG BGPIO1/I2C_SCL IC506 BALANCED Vcc = 2.0~5.5V Recommend Vcc = 3.3V IC20 UART1 : CPU I/F Vin H : 0.7Vcc @3.0V...
  • Page 62: Schematic Diagrams

    NP-S2000 SCHEMATIC DIAGRAMS NET 1/3 (For factory) (For factory) CB511 CB512 FLASH ROM 16 MB NET (1) No replacement part available. IC507 サービス部品供給なし IC509 RESET IC IC504 IC507 IC509 IC507 IC508 EEPROM No replacement part available. サービス部品供給なし MAIN IC504 IC502: MX29GL128ELT2I-90G...
  • Page 63 NP-S2000 NET 2/3 NET (1) IC510: TC7WH14FK IC513: IP101ALF Triple schmitt inverter Single port 10/100 fast ethernet transceiver V CC MII/SNI/RMII Interface 100Mbps 10Mbps 100Mbps 4B/5B 4B/5B Serial to Encoder Decoder 10Mbps Parallel 100Mbps 100Mbps MII Registers 10Mbps Descrambler Manchester/...
  • Page 64 NP-S2000 NET 3/3 SYSTEM CONNECTOR (For factory) CB581 Page 66 to DAC (2)_CB208 IC581: TC7WU04F Triple inverter CB585 V CC (For factory) IC581 COAXIAL DIGITAL OUT IC581 OPTICAL CB586 Page 63 to NET (1)_CB505 (For factory) CB583 NETWORK IN CB582...
  • Page 65 NP-S2000 DAC 1/4 DAC (1) 12.5 OUT L 12.5 12.5 -0.9 -4.8 IC19 IC14 -0.9 IC15 ANALOG OUT IC15 -12.4 -4.8 IC19 -12.4 IC4: CS230011-CZZR Clock multiplier 12.5 AUX_SRC FILTP CLK_IN IC18 0.1 μF AUX_OUT -12.4 FILTN Fractional-N 12.5 Frequency Synthesizer...
  • Page 66 NP-S2000 DAC 2/4 (Writing port) Writing port Page 67 to DAC (3)_CB701 IC208: R5F21356ANFP Single chip 16 bit microprocessor DAC (2) I/O ports Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6 Peripheral functions UART or...
  • Page 67 NP-S2000 DAC 3/4 DAC (3) Page 69 to POWER (2)_CB352 63.6 W702 (Writing port) (Writing port) No replacement part available. CB706 サービス部品供給なし CB705 VFD2 IC701 VFD1 IC702 No replacement part available. サービス部品供給なし POINT F XL701 (Pin 9 of IC701) IC704...
  • Page 68 NP-S2000 DAC 4/4 Page 62 Page 62 to NET (1)_CB513 to NET (1)_CB512 CB405 CB404 DAC (1) NETWORK OUT CB401 11.5 -12.6 Page 69 to POWER (2)_W351 12.5 12.5 12.5 12.5 -0.5 CB402 12.5 Page 69 -12.4 -12.4 to POWER (1)_W301 -12.4...
  • Page 69 NP-S2000 Notes) 注意 ) POWER Safety measures 安全対策 ・ この製品の内部には高電圧部分があり危険です。 修理の際は、 絶縁性の手袋を使用するなどの安全対策を行ってください。 ・ 下記のコンデンサには電源を OFF にした後も電荷が残り、 高電圧が維持されており危険です。 修理作業前に放電用抵抗 (5 kΩ/10 W) を 下記の各コンデンサの端子間に接続して放電してください。 放電所用時間は各々約 30 秒間です。 POWER (1) P.C.B. の C308 ∼ 311、 POWER (2) P.C.B. の C359 ∼ 361、 C373 POWER (1) 12.7...
  • Page 70: Replacement Parts List

    NP-S2000 ■ REPLACEMENT PARTS LIST ● ELECTRICAL COMPONENT PARTS WARNING • Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed. 印のある部分は、安全確保部品を示しています。部品の交換が必要な場合、パーツリストに記載されている部品を使用し てください。 部品価格ランクは、予告なく変更することがあります。 ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS: C.A.EL.CHP...
  • Page 71 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク WV319200 P.C.B. PCB NET WV319300 P.C.B. PCB NET WV319400 P.C.B. PCB NET WV319500 P.C.B. PCB NET WV319600 P.C.B. PCB NET * CB501 WA901000 CN 10P SE FMNコネクター CB502 WA902000 CN.FMN 20P SE FMNコネクター CB505 VT389000 CN.BS.PIN ベース付ポスト...
  • Page 72 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク C5064-5065 US062100 C.CE.CHP 100pF 50V B チップセラコン C5066-5067 US135100 C.CE.CHP 0.1uF チップセラコン C5068 UF417220 C.EL.CHP 22uF 6.3V チップケミコン C5069 WG251600 C.CE.CHP 4.7uF 6.3V チップセラコン C5070 US063100 C.CE.CHP 1000pF 50V B チップセラコン...
  • Page 73 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク C5244 US065100 C.CE.CHP 0.1uF 50V B チップセラコン C5301 US135100 C.CE.CHP 0.1uF チップセラコン C5302 V9878800 C.CE.CHP 1000pF チップセラコン C5303-5305 US135100 C.CE.CHP 0.1uF チップセラコン C5516 US061100 C.CE.CHP 10pF 50V B チップセラコン C5803 US126100 C.CE.CHP...
  • Page 74 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク WV319900 P.C.B. PCB DAC WV320000 P.C.B. PCB DAC WV320100 P.C.B. PCB DAC WV320200 P.C.B. PCB DAC WV320300 P.C.B. PCB DAC CB202 VB390300 CN.BS.PIN ベースピン CB204 V2329900 CN.BS.PIN 24P TE FFCコネクター CB208 VB390800 CN.BS.PIN コネクタベースポスト CB211 VQ047200 CN.BS.PIN...
  • Page 75 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク C82-84 WE102900 C.PP 0.01uF 100V J PPコン WE102400 C.PP 3900pF 100V J PPコン WE102900 C.PP 0.01uF 100V J PPコン WE102400 C.PP 3900pF 100V J PPコン C88-89 WE102900 C.PP 0.01uF 100V J PPコン...
  • Page 76 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク C232-234 US064100 C.CE.CHP 0.01uF 50V B チップセラコン C235 US063100 C.CE.CHP 1000pF 50V B チップセラコン C236-238 US135100 C.CE.CHP 0.1uF チップセラコン C239 US061150 C.CE.CHP 15pF 50V B チップセラコン C241-242 US135100 C.CE.CHP 0.1uF チップセラコン...
  • Page 77 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク C732 US061470 C.CE.CHP 47pF 50V B チップセラコン C733 US135100 C.CE.CHP 0.1uF チップセラコン C734 US061470 C.CE.CHP 47pF 50V B チップセラコン C735 UF027470 C.EL.CHP 47uF チップケミコン C736 US061330 C.CE.CHP 33pF 50V B チップセラコン...
  • Page 78 NP-S2000 Ref No. Part No. Description Remarks Markets 部 品 名 ランク IC208 YA833A00 IC.CPU R5F21356ANFP CPU unwritten CPU IC IC210 X3586B00 IC TC74VHCT08AFT EL,K ロジックIC * IC211 YC280A00 IC TC7SZ126FU BUS BUF ロジックIC IC212 X3586B00 IC TC74VHCT08AFT EL,K ロジックIC IC213 X8398A00 IC TC7SET08FU(T5L,JF) ロジックIC...
  • Page 79 NP-S2000 DAC and POWER Ref No. Part No. Description Remarks Markets 部 品 名 ランク ST1-2 WG095100 SCR.TERM スクリューターミナル ST701-702 WG095100 SCR.TERM スクリューターミナル SW701-702 WD483100 SW.TACT SKRGAAD010 タクトスイッチ * V701 WV321300 FL.DSPLY GP1264AI 螢光表示管 XL201 WF997400 RSNR.CE 20MHz セラミック振動子 XL701 WF997400 RSNR.CE 20MHz セラミック振動子...
  • Page 80 NP-S2000 POWER Ref No. Part No. Description Remarks Markets 部 品 名 ランク C608 WD257600 C.PP 0.047uF 800V PPコン C609 WJ609700 C.MYLAR 4700pF 100V マイラーコン C610 UR266100 C.EL ケミコン C611-612 V6185300 C.CE.SAFTY 0.01uF 275V 規格認定コンデンサ C613 UR049330 C.EL 3300uF ケミコン C614 WE102900 C.PP 0.01uF...
  • Page 81 NP-S2000 POWER Ref No. Part No. Description Remarks Markets 部 品 名 ランク Q606 VV655400 TR.DGT DTC114EKA デジタルトランジスタ Q771-772 VV655400 TR.DGT DTC114EKA デジタルトランジスタ Q773 VV655000 TR.DGT DTA114EKA デジタルトランジスタ R329 V8070400 R.MTL.FLM 15Ω 金属被膜抵抗 R330-333 HV754100 R.CAR.FP 10Ω 1/4W 不燃化カーボン抵抗 R334 V8070400 R.MTL.FLM 15Ω...
  • Page 82 NP-S2000 Carbon Resistors Value 1/4W Type Part No. 1/6W Type Part No. Value 1/4W Type Part No. 1/6W Type Part No. 1.0 Ω HJ35 3100 HF85 3100 11 kΩ HF45 7110 HF45 7110 ✻ 1.8 Ω 3180 12 kΩ 7120...
  • Page 83 NP-S2000 ● OVERALL ASSEMBLY Ref No. Part No. Description Remarks Markets 部 品 名 ランク * 1-1 WY075800 SIDE PANEL ASSEMBLY BL L/R 1pair (MD) WU98090+WU98100 サイドパネルAss’y * 1-1 WY075700 SIDE PANEL ASSEMBLY SI L/R 1pair (MN) WU96960+WU98010 サイドパネルAss’y * 1-1 WY075900 SIDE PANEL ASSEMBLY...
  • Page 84 NP-S2000 ● MAIN UNIT Ref No. Part No. Description Remarks Markets 部 品 名 ランク * 3-1 WV319200 P.C.B. ASSEMBLY PCB NET * 3-1 WV319300 P.C.B. ASSEMBLY PCB NET * 3-1 WV319400 P.C.B. ASSEMBLY PCB NET * 3-1 WV319500 P.C.B. ASSEMBLY PCB NET * 3-1 WV319600 P.C.B. ASSEMBLY PCB NET...
  • Page 85 NP-S2000 ● FRONT PANEL UNIT Ref No. Part No. Description Remarks Markets 部 品 名 ランク * 3-2 WV319900 P.C.B. ASSEMBLY PCB DAC * 3-2 WV320000 P.C.B. ASSEMBLY PCB DAC * 3-2 WV320100 P.C.B. ASSEMBLY PCB DAC * 3-2 WV320200 P.C.B. ASSEMBLY PCB DAC * 3-2 WV320300 P.C.B.
  • Page 86: Remote Control

    NP-S2000 ■ REMOTE CONTROL SCHEMATIC DIAGRAM PANEL KEY NO. LAYOUT KEY NO. LAYOUT NPS2 Code Key name Customer Data SOURCE 7887 5EA1 3.3 ohms (Power) 7887 0FF0 IR_DIODE DIMMER 7887 BA45 DISPLAY 7887 4EB1 10 REPEAT 7887 0CF3 220 ohms...
  • Page 87 NP-S2000 ■ ADVANCED SETUP MENU ■ 拡張設定メニュー一覧...

Table of Contents