Download  Print this page

Honeywell SS2 Series Installation Manual And Operating Manual

Multi-spectrum digital electro-optical fire detectors
Hide thumbs

Advertisement

Quick Links

Installation Guide and Operating Manual
Multi-Spectrum Digital
Electro-Optical Fire Detectors
Models SS2-A, SS2-AN, SS2-AH, and SS2-AM
Stand-Alone Mode

Advertisement

loading

  Related Manuals for Honeywell SS2 Series

  Summary of Contents for Honeywell SS2 Series

  • Page 1 Installation Guide and Operating Manual Multi-Spectrum Digital Electro-Optical Fire Detectors Models SS2-A, SS2-AN, SS2-AH, and SS2-AM Stand-Alone Mode...
  • Page 2 In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are subject to change without notice.
  • Page 3 It may also be used to alert against unsafe practices. CAUTION: Symbol on the equipment refers the user to the product manual for additional information. The symbol appears next to required information in the manual. HONEYWELL...
  • Page 4: Table Of Contents

    SS2-A, -AN, -AH, and -AM Detector Modules Replacement ..... 17 Detector Repair ..................17 SECTION 4 / DETECTOR PINOUT DATA ............18 TABLE 1: Stand-Alone Model SS2 Detector Connectors - Pinouts................18 SECTION 5 / DETECTOR LABEL DRAWINGS ..........19 INDEX ..................20 HONEYWELL...
  • Page 5: Approvals

    Class I, Div. 1 & 2, Groups A, B,C, & D Class II, Div. 1 & 2, Groups E, F, & G Class III Class I , Zone 1 AEx d IIC Ex d IIC; Ex tb IIIC T135°C HONEYWELL...
  • Page 6: Section 1: Familiarization

    Fire/Security Panels. For Stand-Alone operation, the Detector’s Fault relay is automatically configured by the on-board microprocessor. The input current of the Detector is about 15 mA higher in the Stand-Alone mode compared to operation as part of FS2000 System. HONEYWELL...
  • Page 7: Fs2000 System Operation

    FS2000 System Controller using the four wire FS2000 FireBus. The FireBus provides the 24 Volts DC power for the Detector and RS-485 digital communication (Refer to Honeywell Analytics document MN0003: "FS2000 FIRE EARLY WARNING SYSTEM - INSTALLATION and OPERATIONS GUIDE").
  • Page 8: Testing

    Manual Testing For manual testing the Detector may be exposed to an actual industry standard open flame or to a Test Lamp simulating a fire. For Honeywell Analytics model SS2 Multi-Spectrum Fire Detectors, it is mandatory to use the handheld UV/IR Test Lamp, Model No FT-2045 or FT-2145.
  • Page 9 The FT-2045 and FT-2145 Test Lamps are housed in an Explosion-proof enclosure, powered by internal rechargeable batteries, and designed for indoor and outdoor use. For additional information on the Test Lamp, refer to Honeywell Analytics Specification SP0242 for the FT-2045 or 1505-008A for the FT-2145. HONEYWELL...
  • Page 10: Section 2: Installation

    Detector's terminals and an Approved Fire Alarm Panel. Use only approved junction boxes and terminal strips. Avoid wire splices. However, if wire splices are necessary, Honeywell Analytics recommends soldering all splices. The use of good wiring practices will greatly improve the ease and reliability of installation, and facilitate servicing.
  • Page 11: Enclosure Installation (Optional)

    2.2.2 Install Conduit (If not already installed). Figure 2. Model SS2 Detector with SM4 Swivel Mount Wiring Detectors To wire a Model SS2 Detector, remove its module from the enclosure. After wiring connections re-install the module in the enclosure. HONEYWELL...
  • Page 12: Figure 3: Model Ss2 Detector Enclosure - Side View

    Caution: Do not touch the detector elements on the front of the Model SS2 Detector modules. If touched accidentally, clean them per instructed of Section 3.2. 1.50 4.38 ¾ NPT 2.40 0.67 2.09 1.10 4.66 Figure 3: Model SS2 Detector Enclosure - Side View HONEYWELL...
  • Page 13: Figure 4. Model Ss2 Detector Enclosure - Back View

    OPERATOR MANUAL // SECTION 2: INSTALLATION Figure 4. Model SS2 Detector Enclosure - Back View Figure 5. Models SS2-A, SS2-AN, SS2-AH, and SS2-AM. HONEYWELL...
  • Page 14 Insert the Fault relay cables into the metal enclosure base through one of the conduit openings. b. Connect the wires to the four pin WECO terminal J2. Install the wires into J2 Pins 1 and 2 and firmly tighten down the slotted screws with a small screwdriver. HONEYWELL...
  • Page 15 If necessary, clean the detectors and windowed cover according to the instructions in Section 3.2. c. Screw down the metal enclosure top windowed cover until secure and tighten the allen-head "tamper-proof" screw. HONEYWELL...
  • Page 16: Section 3 / Maintenance And Troubleshooting

    DO NOT handle a module without adequate grounding precautions. If Model SS2 Module must be shipped back to the factory for repair, it MUST be packed in static protected material. If static protected material is not available, carefully wrap the Module with aluminum foil. HONEYWELL...
  • Page 17: Cleaning Windowed Enclosures And Detectors

    No Power Fault: The Detector will Fault if the voltage supplied to it is interrupted or turned off. (No LED indication.) d. Self-Checking Fault: The Detector will fault if its internal microcomputer self-checking circuitry and software finds a failure. HONEYWELL...
  • Page 18: Ss2-A, -An, -Ah, And -Am Detector Modules Replacement

    Module with aluminum foil. An RMA (Return Material Authorization) is required for all returns to the factory. Contact the Honeywell Analytics Customer Service Department or your Distributor for an RMA number before shipping a unit back to the factory.
  • Page 19: Section 4 / Detector Pinout Data

    3 Fault Relay Common 3 Fire Relay #2 Common 4 Fault Relay Normally Open 4 Fire Relay #2 Normally Closed J3: FIRE RELAY 1 Fire Relay Common 2 Fire Relay Normally Open 3 Fire Relay Common 4 Fire Relay Normally Closed HONEYWELL...
  • Page 20: Section 5 / Detector Label Drawings

    -40°C to Stainless Steel +85°C +75°C +60°C Black White LB-6093- 0.020' A l -40°C to -40°C to -40°C to 1100-H14 +85°C +75°C +60°C Polished Black LB-6093- 0.020' 316 -40°C to -40°C to -40°C to Stainless Steel +85°C +75°C +60°C HONEYWELL...
  • Page 21: Index

    SS2-AM ......... 13 Wiring ........9 SS2-AN ......... 13 FireLogic ......... 6 Stand-Alone ......5 Static Damage ......9 Flame Detector (See Detector) .. 6 Grounding ........ 9 Test Source ......7 Theory of Operation ....6 Troubleshooting ..... 15 HONEYWELL...
  • Page 22 Honeywell Analytics warrants its Products against defects in material and workmanship under normal use and service for a period of two (2) years from the date of shipment as described herein. Honeywell Analytics, at its option, will repair or replace, at no charge, such products found to be defective during the warranty period provided that they are returned in accordance with the terms of this warranty.
  • Page 23 Honeywell Analytics Asia Pacific Co., Ltd. #701 Kolon Science Valley (1) 43 Digital-Ro 34-Gil, Guro-Gu Seoul, 152-729 Korea Email: analytics.ap@honeywell.com Internet These Honeywell websites may be of interest to Industry Solution customers. Honeywell Organization Corporate www.honeywell.com Honeywell Analytics www.honeywellanalytics.com Telephone Contact us by telephone at these numbers.
  • Page 24 1998M0908 Rev. A July, 2014 © 2014 Honeywell International Inc.

This manual is also suitable for:

Ss2-aSs2-anSs2-amSs2-ah