Professional series radar, laser and safety detector (16 pages)
Summary of Contents for Beltronics LP904
Page 1
Operating Manual For LaserPro ™ Model LP904 Ultimate Performance. Proven Technology.
Page 2
LaserPro capabilities with a dash or Remote Installation Radar/Laser/Safety detector from BELTRONICS. Please Note: Operating BEL LaserPro not a license to speed. Observe the local speed limits and laws governing the user of a Laser defense product.
Quick Overview of Functions and LED Display 8. Green Power On LED: Illuminates to confirm LaserPro™ 904 is operational. 4. Red “F” LED: illuminates to confirm a Laser alert from the front. 1. P/V Button: Power and Volume button. 7. Audio Speaker: All audio alerts are emitted from this opening.
DIS button to disarm LaserPro ™ 904 from further “blocking” traffic Laser signals. BELTRONICS recommends that the DIS button be pressed within five seconds of a Laser alert. Five seconds provides you enough time to adjust your vehicle speed and avoid any undue attention you may draw to yourself and your vehicle.
General Operations/Disarm Function General Operation Once you have BEL LaserPro properly installed, you’re ready for unencumbered travel. Assuming ™ LaserPro 904 is “hard wired” into your vehicle’s electrical system, each time you start your vehicle, LaserPro ™ 904 will start up. Conversely, each time your shut your vehicle off, LaserPro shut down.
How Traffic Laser Operates Any signal received while in this mode will result in an alert – BUT NO “BLOCKING” OF THE LASER SIGNAL WILL OCCUR. When no Laser signal has been detected for 60 seconds, a short “beep” will be heard, coupled with FULL illumination of the green power on LED.
taken seriously. There are limitations to LIDAR equipment. LIDAR is much more sensitive to inclement weather conditions than RADAR, and a LIDAR gun’s range will be decreased by anything affecting visibility such as rain, fog, or smoke. A LIDAR gun cannot operate through glass and it must be stationary to get an accurate reading.
Front Transceiver Error If one, or both of the front- mounted transceivers are not communicating properly or become disconnected, the red “F” LED (front) on the display will illuminate fully coupled with an audible tone. This alert will continue until the unit is turned off, indicating that service is required.
Problem LaserPro™ 904 does not appear to be ON Solution: • Check that the P/V control is turned ON. • Check that the vehicle ignition is ON. • Check all connections. Problem LaserPro™ 904 gave no alert when a police car was in sight Solution: •...
904 is legal to use in most states except for California, Utah, Virginia, and Minnesota. Check with your local code before use, or call BELTRONICS at: 800- 737-9393. Q. Can I use a traditional dash mounted Radar/Laser detector with LaserPro A.
3. In the event of a defect, malfunction or other failure to consumer to this warranty, BELTRONICS will, at is sole discretion, repair or replace the unit at no charge. You are responsible for all shipping costs in connection with warranty service pursuant to this warranty.
Warranty Service If you feel your LaserPro review this manual, particularly the section on Troubleshooting. If you still feel service is required, please follow the instructions below: 1. To obtain service during the warranty period, please call the appropriate number below to obtain an RA number and shipping instructions.
Post Warranty Service The following arrangements apply if the warranty period has expired or you are not able to provide a copy of your dated sales receipt indicating purchase within the last 12 months. 1. Return your unit to the appropriate address under Warranty Service and follow steps 1 through 3(b) outlined in that section.
Page 16
#4,952,936 #4,961,074 #5,587,916 #5,600,132 Canada #1,187,586 #1,187,602 Other Patents Pending is a registered trademark of BELTRIONCS USA, Inc. LaserPro 904 is a trademark of BELTRONICS USA, Inc. Printed in Canada Head Office Canada L5L 1J9 #4,630,054 #5,402,087 #1,295,714 273004-12 #4,939,521...
Need help?
Do you have a question about the LP904 and is the answer not in the manual?
Questions and answers