Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cinterion PVS8
Summary of Contents for Cinterion PVS8
- Page 1 PVS8 Version: 03.000a DocId: PVS8_HIO_v03.000a...
- Page 2 UCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL. THIS DOCUMENT CON- TAINS INFORMATION ON CINTERION PRODUCTS. THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT CINTERION'S DISCRETION. CINTERION WIRELESS MODULES GMBH GRANTS A NON-EXCLUSIVE RIGHT TO USE THE PRODUCT.
-
Page 3: Table Of Contents
5.1.1 Antenna Installation ................27 GNSS Antenna Interface ................. 28 Mechanics, Mounting and Packaging ..............30 Mechanical Dimensions of PVS8..............30 Sample Application....................32 Reference Approval ....................34 Reference Equipment for Type Approval ............34 Compliance with FCC and IC Rules and Regulations ........35 Appendix........................ - Page 4 PVS8 Hardware Interface Overview Tables Tables Table 1: Directives ....................... 10 Table 2: Standards of North American type approval ..........10 Table 3: Requirements of quality ................. 10 Table 4: Standards of the Ministry of Information Industry of the People’s Republic of China ................
- Page 5 ESD protection for passive GNSS antenna ........... 29 Figure 7: PVS8 – top and bottomview................30 Figure 8: Dimensions of PVS8 (all dimensions in mm) ..........31 Figure 9: PVS8 sample application ................33 Figure 10: Reference equipment for type approval ............34 PVS8_HIO_v03.000a...
-
Page 6: Document History
PVS8 Hardware Interface Overview 0 Document History Document History Preceding document: "PVS8 Hardware Interface Description" Version 03.000 New document: "PVS8 Hardware Interface Description" Version 03.000a Chapter What is new Revised antenna gain limit for 850 MHz band. Added module label number. -
Page 7: Introduction
Introduction The document describes the hardware of the PVS8 module, designed to connect to a cellular device application and the air interface. It helps you quickly retrieve interface specifications, electrical and mechanical details and information on the requirements to be considered for in- tegrating further components. - Page 8 PVS8 Hardware Interface Overview 1.2 Terms and Abbreviations Abbreviation Description Digital Signal Processor DTMF Dual Tone Multi Frequency Discontinuous Transmission Enhanced Full Rate Electromagnetic Compatibility Effective Radiated Power Electrostatic Discharge ETSI European Telecommunications Standards Institute EVRC Enhanced Variable Rate Codec Federal Communications Commission (U.S.)
- Page 9 PVS8 Hardware Interface Overview 1.2 Terms and Abbreviations Abbreviation Description Negative Temperature Coefficient PBCCH Packet Switched Broadcast Control Channel Printed Circuit Board Power Control Level Pulse Code Modulation Personal Communication System, also referred to as GSM 1900 Pull Down resistor (appr. 100k)
-
Page 10: Regulatory And Type Approval Information
1.3.1 Directives and Standards PVS8 has been designed to comply with the directives and standards listed below. It is the responsibility of the application manufacturer to ensure compliance of the final product with all provisions of the applicable directives and standards as well as with the technical spec- ifications provided in the "PVS8 Hardware Interface Description". -
Page 11: Table 4: Standards Of The Ministry Of Information Industry Of The People's Republic Of China
Period, of this product is 20 years as per the symbol shown here, unless otherwise marked. The EPUP is valid only as long as the product is operated within the operating limits described in the Cinterion Hardware Interface Description. Please see... -
Page 12: Sar Requirements Specific To Portable Mobiles
Mobile phones, PDAs or other portable transmitters and receivers incorporating a CDMA mod- ule must be in accordance with the guidelines for human exposure to radio frequency energy. This requires the Specific Absorption Rate (SAR) of portable PVS8 based applications to be evaluated and approved for compliance with national and/or international regulations. -
Page 13: Selv Requirements
PVS8 Hardware Interface Overview 1.3 Regulatory and Type Approval Information 1.3.3 SELV Requirements The power supply connected to the PVS8 module shall be in compliance with the SELV re- quirements defined in EN 60950-1. 1.3.4 Safety Precautions The following safety precautions must be observed during all phases of the operation, usage, service or repair of any cellular terminal or mobile incorporating PVS8. - Page 14 PVS8 Hardware Interface Overview 1.3 Regulatory and Type Approval Information IMPORTANT! Cellular terminals or mobiles operate using radio signals and cellular networks. Because of this, connection cannot be guaranteed at all times under all conditions. Therefore, you should never rely solely upon any wireless device for essential com- munications, for example emergency calls.
-
Page 15: Product Concept
- User plane - gpsOneXTRA™ General Power saving modes Software AT commands Hayes, 3GPP TS 27.007 and 27.005, and proprietary Cinterion Wireless Modules commands as well as provider specific CDMA commands Audio Audio speech codecs 3GPP2: EVRC, EVRC-B (4GV-NB), QCELP, AMR-NB... - Page 16 (Over-the-Air Parameter Administration) Evaluation kit Evaluation module PVS8 module soldered onto a dedicated PCB that can be connected to an adapter in order to be mounted onto the DSB75. DSB75 DSB75 Development Support Board designed to test and type approve Cinterion Wireless Modules and provide a sample configuration for appli- cation engineering.
-
Page 17: Pvs8 System Overview
GNSS Module Power IGT, Serial Analog Net state/ Digital Wake- supply Emergency Off ASC0 audio audio status Host Application PCM or I2S On/Off Controller Codec Application Figure 1: PVS8 system overview PVS8_HIO_v03.000a Page 17 of 37 2013-04-08 Confidential / Preliminary... -
Page 18: Application Interface
PVS8 Hardware Interface Overview 3 Application Interface Application Interface PVS8 is equipped with an SMT application interface that connects to the external application. The host interface incorporates several sub-interfaces described in the following sections: • Operating modes - see Section 3.1... -
Page 19: Operating Modes
PVS8 Hardware Interface Overview 3.1 Operating Modes Operating Modes The table below briefly summarizes the various operating modes referred to in the following chapters. Table 6: Overview of operating modes Mode Function Normal CDMA SLEEP Power saving set automatically when no call is in progress and the USB... -
Page 20: Power Supply
PVS8 Hardware Interface Overview 3.2 Power Supply Power Supply PVS8 needs to be connected to a power supply at the SMT application interface - 6 lines each BATT+ and GND. There are three separate voltage domains for BATT+: • BATT+_PA1 with 2 lines for the first power amplifier supply •... -
Page 21: Usb Interface
PVS8 Hardware Interface Overview 3.3 USB Interface USB Interface PVS8 supports a USB 2.0 High Speed (480Mbit/s) device interface that is Full Speed (12Mbit/s) compliant. The USB interface is primarily intended for use as command and data interface and for downloading firmware. -
Page 22: Serial Interface Asc0
The significant levels are 0V (for low data bit or active state) and 1.8V (for high data bit or in- active state). PVS8 is designed for use as a DCE. Based on the conventions for DCE-DTE connections it communicates with the customer application (DTE) using the following signals: •... -
Page 23: Table 7: Dce-Dte Wiring Of Asc0
PVS8 Hardware Interface Overview 3.4 Serial Interface ASC0 Table 7: DCE-DTE wiring of ASC0 V.24 circuit DCE Line function Signal direction Line function Signal direction TXD0 Input Output RXD0 Output Input RTS0 Input Output CTS0 Output Input 108/2 DTR0... -
Page 24: Analog Audio Interface
AT commands (except for mode 1). When shipped from factory, all audio parameters of PVS8 are set to audio mode 1. This is the default configuration optimised for the Votronic HH-SI-30.3/V1.1/0 handset and used for type approving the Cinterion Wireless Modules reference configuration. -
Page 25: Gnss Receiver
PVS8 Hardware Interface Overview 4 GNSS Receiver GNSS Receiver PVS8 integrates a GNSS receiver that offers the full performance of GPS/GLONASS technol- ogy. The GNSS receiver is able to continuously track all satellites in view, thus providing accu- rate satellite position data. -
Page 26: Antenna Interfaces
The external antenna must be matched properly to achieve best performance regarding radi- ated power, modulation accuracy and harmonic suppression. Matching networks are not in- cluded on the PVS8 PCB and should be placed in the host application, if the antenna does not ... -
Page 27: Antenna Installation
PVS8 Hardware Interface Overview 5.1 CDMA Antenna Interface 5.1.1 Antenna Installation The antenna is connected by soldering the antenna pads and their neighboring ground pads directly to the application’s PCB. The distance between the antenna pads and their neighboring GND pads has been optimized for best possible impedance. -
Page 28: Gnss Antenna Interface
PVS8 Hardware Interface Overview 5.2 GNSS Antenna Interface GNSS Antenna Interface In addition to the RF antenna interface PVS8 also has a GNSS antenna interface. The GNSS antenna installation and connector are the same as for the RF antenna interface (see Section 5.1.1). -
Page 29: Figure 6: Esd Protection For Passive Gnss Antenna
PVS8 Hardware Interface Overview 5.2 GNSS Antenna Interface Figure 6 shows sample circuits realizing ESD protection for a passive GNSS antenna. Module SMT interface VGNSS Not used 47pF ANT_GNSS_DC (Optional) Passive GNSS protection antenna 10nH ANT_GNSS Figure 6: ESD protection for passive GNSS antenna PVS8_HIO_v03.000a... -
Page 30: Mechanics, Mounting And Packaging
PVS8 Hardware Interface Overview 6 Mechanics, Mounting and Packaging Mechanics, Mounting and Packaging Mechanical Dimensions of PVS8 Figure 7 shows a 3D view of PVS8 and provides an overview of the board's mechanical di- mensions. For further details see Figure Length: 33mm Width:... -
Page 31: Figure 8: Dimensions Of Pvs8 (All Dimensions In Mm)
PVS8 Hardware Interface Overview 6.1 Mechanical Dimensions of PVS8 Position marker Internal use; Not to be soldered Dimensions of Figure 8: PVS8 (all dimensions in mm) PVS8_HIO_v03.000a Page 31 of 37 2013-04-08 Confidential / Preliminary... -
Page 32: Sample Application
The PWR_IND line is an open collector that needs an external pull-up resistor which connects to the voltage supply VCC µC of the microcontroller. Low state of the open collector pulls the PWR_IND signal low and indicates that the PVS8 module is active, high level notifies the Pow- er-down mode. -
Page 33: Figure 9: Pvs8 Sample Application
PVS8 Hardware Interface Overview 7 Sample Application PVS8 Sample Application Current limiter <50mA Figure 9: PVS8 sample application PVS8_HIO_v03.000a Page 33 of 37 2013-04-08 Confidential / Preliminary... -
Page 34: Reference Approval
8 Reference Approval Reference Approval Reference Equipment for Type Approval The Cinterion Wireless Modules reference setup submitted to type approve PVS8 is shown in Figure 10. The module (i.e., the evaluation module) is connected to the DSB75 by means of a flex cable and a special DSB75 adapter. -
Page 35: Compliance With Fcc And Ic Rules And Regulations
Manufacturers of mobile or fixed devices incorporating PVS8 modules are authorized to use the FCC Grants and Industry Canada Certificates of the PVS8 modules for their own final prod- ucts according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID QIPPVS8"... -
Page 36: Appendix
PVS8 Hardware Interface Overview 9 Appendix Appendix List of Parts and Accessories Table 9: List of parts and accessories Description Supplier Ordering information PVS8 Cinterion Standard module Cinterion Wireless Modules IMEI: Packaging unit (ordering) number: L30960-N2650-A300 Module label number: S30960-S2650-A300-1... -
Page 37: Table 10: Molex Sales Contacts (Subject To Change)
PVS8 Hardware Interface Overview 9.1 List of Parts and Accessories Table 10: Molex sales contacts (subject to change) Molex Molex Deutschland GmbH American Headquarters For further information please click: Otto-Hahn-Str. 1b Lisle, Illinois 60532 http://www.molex.com 69190 Walldorf U.S.A. Germany...
Need help?
Do you have a question about the PVS8 and is the answer not in the manual?
Questions and answers