Page 1
Pos : 2 /T ec hDOC /Seni ng/Intr o's/Erste Seite/Intro: CM 3 @ 7\mod_1422878233031_19.doc x @ 126124 @ @ 1 MN F08 001 EN DOK-347E Turbin Check Meter === Ende der Liste für T extmar ke Intro === ® Sening is a registered trademark of FMC Technologies...
Page 2
Pos : 6 /T ec hDOC /Seni ng/Allgemein/| FÜ1---> Inhal ts verzeic hnis (Deutsc h) @ 2\mod_1340182989966_19.doc x @ 41391 @ @ 1 History Revision Date Originator Status Description Rev. 1.01 October 2014 Created First edition Rev. 1.10 Januar 2015 / HS / jp / Div. modifications ® Sening is a registered trademark of FMC Technologies...
Battery Replacement ..................12 Technical Data ________________________________________ 14 CM3 ........................ 14 Repairs and Replacement Parts ..............14 Address and contact details _____________________________ 15 Appendix A. Drawings and Approvals _______________________ 16 Index _____________________________________________ 16 ® Sening is a registered trademark of FMC Technologies...
Page 4
51.250243 – Holder – CM3-AV ....................18 Approvals 19 KEMA - Certificate Of Conformity ..................... 19 Pos : 8 /T ec hDOC /Seni ng/Allgemein/| 1---> Allgemei nes @ 0\mod_1307366793031_19.doc x @ 5771 @ 1 @ 1 ® Sening is a registered trademark of FMC Technologies...
Background information Short-Tip, e.g. “See more detailed information in chapter XX”. Option Special case. Function Functional description. NOTE: indicates a special situation. ATTENTION: particular attention is to be paid. ® Sening is a registered trademark of FMC Technologies...
The CM3 contains precision, high quality components. Therefore, mechanical influences which do not result from operation (e.g. through being dropped) must be avoided. § Measurements which are subject to mandatory W&M certification shall not be carried out with this device. ® Sening is a registered trademark of FMC Technologies...
This air will be measured as discharged volume if flow is not interrupted. Pos : 17 /T echD OC/Seni ng/Allgemein/| 1---> Gerätebeschr eibung @ 7\mod_1418651340908_19.doc x @ 123728 @ 1 @ 1 ® Sening is a registered trademark of FMC Technologies...
Connect the CM3 to the discharge coupling on the tank truck. Orientate the CM3 so that the display can be read easily. Make sure that the gaskets in the couplings are in good condition to prevent leakages. ® Sening is a registered trademark of FMC Technologies...
CM3. The device has no ON/OFF switch. It always remains ready for operation. The current consumption is minimised by an internal circuit for maximum battery lifetime. ® Sening is a registered trademark of FMC Technologies...
After discharge remove the product hose and disconnect the CM3 from the discharge coupling. Place the device safely in its storage location. Be sure that that no fuel flows into the environment ® Sening is a registered trademark of FMC Technologies...
Slide the CM3 on the bearing pin back and turn it at the same time by about 45 °. Now the CM3 can be removed from the mandrel. Pos : 31 /T echD OC/Seni ng/Wartung/| 1---> Wartung @ 0\mod_1309780689484_19.doc x @ 9644 @ 1 @ 1 ® Sening is a registered trademark of FMC Technologies...
Only one battery must be replaced at a time, because otherwise all the settings will be deleted. Unscrew the four mounting screws on the membrane keypad to change the batteries. Then remove the membrane keypad and place it on a clean surface. ® Sening is a registered trademark of FMC Technologies...
Page 13
Pos : 34 /T echD OC/Seni ng/Tec hnisc he D aten/| 1---> Tec hnis che D aten @ 0\mod_1309780695828_19.doc x @ 9748 @ 1 @ 1 ® Sening is a registered trademark of FMC Technologies...
• CM3 / 51.250223 (see Appendix 17) and for • CM3-AV / 51.250243 (see page 18). Pos : 38 /T echD OC/Seni ng/Allgemein/| 1---> Ansc hrift und Kontakt @ 0\mod_1307366798125_19.doc x @ 5888 @ 1 @ 1 ® Sening is a registered trademark of FMC Technologies...
MN F08 001 EN DOK-347E Issue/Rev. 1.10 (01/15) CN3 Address and contact details Address and contact details Pos : 39 /T echD OC/Seni ng/Allgemein/Ansc hrift und Kontakt @ 3\mod_1358149758511_19.doc x @ 71170 @ @ 1 Our service department will be happy to assist and can be contacted as follows: Measurement Solutions F.
MN F08 001 EN DOK-347E Issue/Rev. 1.10 (01/15) CN3 Address and contact details Appendix A. Drawings and Approvals Pos : 42 /T echD OC/Seni ng/08-Mess anlag en/D OK-347_CM3/Tabelle: Zeic hnungen und Zul ass ung en CM 3_E @ 7\mod_1423743007641_19.doc x @ 126928 @ @ 1...
Page 17
Pos : 46.2 /T echD OC/Seni ng/Zeic hnungen/DOK-347_CM 3/51.250223 – T urbi nenz ähl er - CM 3 (New) @ 7\mod_1423736555294_19.doc x @ 126880 @ @ 1 51.250223 – Turbine Check Meter - CM3 ® MN F08 001 EN DOK-347E Issue/Rev. 1.10 (01/15) Sening is a registered trademark of FMC Technologies...
Page 18
Pos : 46.3 /T echD OC/Seni ng/Zeic hnungen/DOK-347_CM 3/51.250243 – Aufnahmeeinrichtung – CM 3-AV (New) @ 7\mod_1423736603412_19.doc x @ 126903 @ @ 1 51.250243 – Holder – CM3-AV 18 MN F08 001 EN DOK-347E Issue/Rev. 1.10 (01/15) ® is a registered trademark of FMC Technologies Sening...
Page 19
Pos : 48 /T echD OC/Seni ng/Konfor mitäts er klär ung en/KEMA_C ertificate_ Of_Confor mity_CM3 @ 7\mod_1423150009802_19.doc x @ 126768 @ @ 1 KEMA - Certificate Of Conformity === Ende der Liste für T extmar ke Zeic hnungen === ® MN F08 001 EN DOK-347E Issue/Rev. 1.10 (01/15) Sening is a registered trademark of FMC Technologies...
Page 20
Pos : 50 /T echD OC/Seni ng/Intro's/Letzte Sei te/Intro: SENIN GVertriebAdr ess en @ 0\mod_1307366798484_19.doc x @ 5901 @ @ 1 === Ende der Liste für T extmar ke Intro_LetzteSeite === The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications are currently in effect.