Related Manuals for Genvex Optima 100 Opus
Summary of Contents for Genvex Optima 100 Opus
- Page 1 Optima 100 Opus Optima 100 Design G e n v e x A / S S v e r i g e s v e j 6 D K - 6 1 0 0 H a d e r s l e v T l f . : + 4 5 7 3 5 3 2 7 0 0 w w w. g e n v e x . d k...
-
Page 2: Table Of Contents
Table of contents Page 1. Mounting Design .............3 1.1 Installation of the control panel ........3 1.2 Mounting ..............3 2. Mounting Opus ............4 2.1 Installation of the control panel ........4 2.2 Mounting ..............4 3. Operation..............5 3.1 Use and changing of the settings ......5 3.2 Ventilator Speed ............5 3.3 Filter alarm...............6 3.4 Bypass ..............7... -
Page 3: Mounting Design
1. Mounting Design A low-current cable 8 x 0.25 mm2 must be attached between the unit and the control panel. 50 m is the maximum cable length. The voltage drop for cable 1.1 Installation of the control panel lengths over 50 m is too high and can result in unreliable operation. -
Page 4: Mounting Opus
3.1 Use and changing of the settings Optima 100 Design is operated via the B3, B4 and B5 buttons. Optima 100 Opus is operated via the B3 and B5 buttons. With Opus the B4 button enables the B3 and 2.2 Mounting B5 buttons to be held down at the same time. -
Page 5: Ventilator Speed
3.2 Ventilator Speed Level 2 outlet airflow Level 2 is the recommended operating level for an optimal Both ventilators can be set independently of each other, indoor climate and should be commissioned to meet the so that the airflow at the inlet and outlet are equal, which building’s ventilation requirements. -
Page 6: Filteralarm
3.3 Filteralarm To return to the main display, press button B4 repeatedly until all of the LED’s stop flashing. A built-in filter timer measures the amount of time the unit has operated since the last filter replacement. Level 2 inlet airflow Level 2 inlet airflow is to be adjusted to match the level 2 The filter timer can be set between 1-6, which corresponds outlet airflow. -
Page 7: Bypass
6 months 3.6 Restoring the factory settings Hold the button B4 down for more than 10 seconds, until If the set points that are installed result in the system not LED D1 begins to flash. operating as expected, and the cause cannot be found, Then press button B5 five times until LED D2/D5 begin to the factory settings can be restored as follows: flash. -
Page 8: Function
If you are unable to maintain/service your system, you If icing occurs or if the unit is to be demounted, the can make a service agreement with the Genvex service relevant environmental requirements must be followed department. If there is a fault with the system, please in association with recycling and disposal of the various contact the Genvex service department. -
Page 9: Troubleshooting
The extract air ventilator is defective. • The exhaust air filter is blocked. If the fault is not stated above, please contact the person who installed the system or the GENVEX customer centre. Subject to technical modifications of Optima 100... -
Page 10: Electrical Diagram
7. Electrical Diagram ES951 Genvex Mains Hygrostat 1x230VAC, 50Hz Potentialfree MAX Fuse 10A Must be connected Contact to earth Must be used Sensor Exhaust air Sensor Heater/Preheater 230V 90°C manu Electrical Heater/Preheater Yell/Green EC-Fan 230V Brown OPTIMA 100 DESIGN Exhaust... -
Page 11: Subject To Technical Modifications Of Optima
Subject to technical modifications of Optima 100... - Page 12 Fax: +44 (0) 1608 652490 E-Mail: genvex@totalhome.co.uk Austria J.Pichler Lufttechnik GmbH A-9021 Klagenfurt Tel.: +43 (0) 463 / 3 27 69 Fax: +43 (0) 463 / 3 75 48 E-Mail: office@pichlerluft.at Published by Genvex A/S, Sverigesvej 6, DK-6100 Haderslev...
Need help?
Do you have a question about the Optima 100 Opus and is the answer not in the manual?
Questions and answers