Alarm Displays; Selecting Peripheral Devices; List Of Options - Mitsubishi FR-S520-*K Series Manual

Alarm Displays

Protective function name
Accelerating
Constant speed
Overcurrent cutoff
Decelerating
Accelerating
Regenerative
Constant speed
overvoltage cutoff
Decelerating
Transistor
Overload cutoff
(electronic thermal
overcurrent protection)
Motor
Fin overheat
( Notes )
1. This functions only when the external thermal relay input (OH) is selected with Pr. 60 to Pr. 63 (input terminal function selection).
2. This applies only when the RS-485 communication function is provided.
3. Major fault : The protective function activates, inverter output is shut off, and an error output is provided.
Minor fault : Output is not shut off even when the protective function activates. It is possible to output minor fault signals by making parameter settings.
4. An error is not output when an undervoltage occurs, but the inverter output is cut off. The operation can be resumed after the power is recovered.
5. This activates only when Pr. 40 (ground fault detection at starting selection) is set to 1.
6. Refer to the instruction manual for details on PS and Err displays.

Selecting Peripheral Devices

Motor
Power
Applicable inverter type
output
voltage
(kW)
0.1 FR-S520-0.1K( -R,C )
0.2 FR-S520-0.2K( -R,C )
0.4 FR-S520-0.4K( -R,C )
3-phase
0.75 FR-S520-0.75K( -R,C )
200V
1.5 FR-S520-1.5K( -R,C )
2.2 FR-S520-2.2K( -R,C )
3.7 FR-S520-3.7K( -R,C )
0.4 FR-S540-0.4K( -R )
0.75 FR-S540-0.75K( -R )
3-phase
1.5 FR-S540-1.5K( -R )
400V
2.2 FR-S540-2.2K( -R )
3.7 FR-S540-3.7K( -R )

List of Options

Name
Parameter unit (8 languages)
Cable for connecting
parameter unit
Power factor improvement AC reactor
Power factor improvement DC reactor
Radio noise filter
Line noise filter
Surge voltage suppression filter
BU type brake unit
Discharging resistor
High power factor converter
Power regeneration common converter
Dedicated standalone reactor
EMC command compatible
noise filter (EU compatible)
EMC filter installation attachment
DIN rail installation attachment
Operation box with frequency meter
Sequential setting operation box
3-speed setting operation box
Remote operation box
Ratio setting box
PG follower
Master controller
Inclined signal box
Deviation detector
Pre-amplifier box
Pilot generator
Deviation sensor
( Notes ) 1. Rated power consumption for the FR Series operation and setting box power supply specifications are 200VAC 50Hz, 200/220V 60Hz, 115VAC 60Hz.
2. The values given in boxes indicate the capacity.
8
3. indicates a value.
4. One 3.7K inverter must be connected. (When using without the 3.7K inverter connected, use as a common converter or regenerative converter is possible, but the power higher harmonic suppression effect will drop.)
5. The EMC filter installation attachment (FR-E5T) must be used when installing SF filter on the FR-S520-2.2K/3.7K.
6. This cannot be mounted on the single-phase 100V power input specification product.
7. A 0.75K filter capacity is used for the 0.4K or less inverter capacity, and a 1.5K filter capacity is used for the 0.75K inverter capacity.
8. The 3-phase 400V input specification product is indicated with an "H" in the type.
9. -AT indicates the type installed in the panel. If -AT is not added, this is an external cooling fin type. Note that either method can be used for the 37K and 55K types by changing the position of the installation legs, so -AT is not added.
Main LED Fault class
Protective function name
display (Note 3)
Major fault Fan trouble
Major fault
Major fault Stall prevention
Major fault
Major fault External thermal relay (Note 1)
PU disconnected (Note 2)
Major fault
Output side ground fault protection
Major fault
(Note 5)
Retry count
Major fault
Parameter memory element error
Major fault
No-fuse
Wire (mm
Magnetic
breaker ( NFB )
contactor (Note 1)
Earth leakage
(MC)
breaker ( NV )
R,S,T
30AF 5A S-N10 2
30AF 5A S-N10 2
30AF 5A S-N10 2
30AF 10A S-N10 2
30AF 15A S-N10 2
30AF 20A S-N11,S-N12 2
30AF 30A S-N20 3.5
30AF 5A S-N10 2
30AF 5A S-N10 2
30AF 10A S-N10 2
30AF 15A S-N20 2
30AF 20A S-N20 2
Type
FR-PU04 Interactive parameter unit with LCD display
FR-CB201(1m)
FR-CB203(3m) Cable for connecting parameter unit and inverter
FR-CB205(5m)
(Note 2)(Note 8) For power factor improvement (power factor approx. 90%)
FR-BAL(H)
FR-BEL(H) (Note 2)(Note 6)(Note 8) For power factor improvement (power factor approx. 95%)
FR-BIF(H)(Note 8) Reduces radio noise
FR-BSF01 Reduces line noise
For micro-surge voltage suppression
FR-ASF-H (Note 2)
(Note 2)(Note 8) Greatly increases regenerative braking performance
BU(H)
GZG GRZG type Discharging resistor for BU type brake unit
FR-HC-(H)7.5K(Note 8) For suppressing higher harmonics
FR-CV- (-AT) (Note 2) (Note 9)
Common converter type power regeneration brake unit
FR-CVL- (Note 2) Reactor for power regeneration common converter
SF- (Note 3) EMC Instruction (EN50081-2) compatible noise filter
* Measures must be taken to prevent malfunction of peripheral devices (earth leakage
(Note 2)
FR-S5NFSA-
breaker), etc., and electric shocks caused by leakage currents.
(Note 2)
FR-E5NF-H
FR-E5T Attachment for installing EMC instruction compatible noise filter (SF1309) onto inverter
FR-UDA01
FR-UDA02 DIN rail installation
FR-UDA03
FR-AX For independent operation with frequency meter, frequency setting unit and start switch
FR-AL For sequential operation (1VA) with external signals (0 to 5VDC, 0 to 10VDC)
FR-AT For operation changing between high, medium and low speed (1.5VA)
FR-FK For remote operation; operation from several places is possible (5VA)
FR-FH For ratio operation; ratios for up to five inverters can be set.
FR-FP For follow-up operation using the signal of a pilot generator (PG). (2VA)
FR-FG Main speed setting unit for parallel operation of several inverters (up to 35 units). (5V)
FR-FC For soft starting/stopping; parallel operation acceleration/deceleration is possible (3VA)
FR-FD For synchronous operation. Used with deviation sensor and synchro. (5VA)
FR-FA Can be used as A/V converter or operation amplifier (3VA)
QVAH-10 70/35VAC 500Hz for tracking operation (at 2500r/min)
YVGC-500W-NS For synchronous operation (mechanical deviation detection). Output 90VAC/90˚
Main LED Fault class
display (Note 3)
Minor fault
Overload Major fault
Overcurrent
—
speed loss
Overvoltage
—
speed loss
Major fault
Major fault
Major fault
Major fault
Major fault
2 )
Motor
Power
output
Applicable inverter type
voltage
(kW)
U,V,W
2
0.1 FR-S520S-0.1K( -R )
2
0.2 FR-S520S-0.2K( -R )
Single-
2
phase
0.4 FR-S520S-0.4K( -R )
2
200V
2
0.75 FR-S520S-0.75K( -R )
2
FR-S520S-1.5K( -R )
1.5
3.5
FR-S510W-0.1K(-R)
0.1
2
Single-
2
0.2 FR-S510W-0.2K(-R)
phase
2
0.4 FR-S510W-0.4K(-R)
100V
2
0.75 FR-S510W-0.75K(-R)
2
(Note) 1. The wire size is for a wiring length of 20m.
Application and specifications, etc.
Main LED
Protective function name
display
Communication error (Note 2)
CPU error
Undervoltage (Note 4)
Write disable error
Parameter
Write-while running error /
setting
mode designation error
error
Calibration error
No-fuse
Magnetic
breaker ( NFB )
contactor
Earth leakage
( MC )
breaker ( NV )
30AF 5A S-N10
30AF 10A S-N10
30AF 10A S-N20
30AF 15A S-N20
30AF 20A S-N21
S-N10
30AF 10A
S-N10
30AF 15A
30AF 20A S-N20
30AF 30A S-N20
Can be used only
with FR-S5 - K-R
type with RS-485
communication function
Connect to input side
Connect to input side
Fault class
(Note 3)
Major fault
Major fault
—
—
—
—
2
Wire (mm )
( Note 1 )
R,S,T U,V,W
2 2
2 2
2 2
2 2
2 2
2 2
2 2
2 2
3.5 2
Applicable inverter
Type with
RS-485
communication
function
Compatible with 0.1K
to 3.7K capacities
Common for
all models
Compatible with FR-S540-
0.4K to 3.7K capacities
FR-S520-0.4K to 3.7K
FR-S540-2.2K to 3.7K
FR-S520-0.1K to 3.7K(Note 4)
FR-S540-0.4K to 3.7K(Note 4)
(Compatible with FR-S520-
0.1K to 3.7K capacities)
Compatible with FR-S520-0.1K
to 3.7K (Note 5), FR-S520S-
0.1K to 1.5K, FR-S510W-0.1K
to 0.75K (Note 7) capacities
FR-S540-0.4K to 3.7K
FR-S520-2.2K/3.7K
Compatible
with capacities
Common for
all models