CAME ZLJ14 Installation Manual
  1. Manuals
  2. Brands
  3. CAME Manuals
  4. Control Unit
  5. ZLJ14
  6. Installation manual
CAME ZLJ14 Installation Manual

CAME ZLJ14 Installation Manual

Control panel for 24 v gearmotors
Hide thumbs Also See for ZLJ14:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual
Control panel
Control panel
for 24 V gearmotors
for 24 V gearmotors
ZLJ14
INSTALLATION MANUAL
FA01082-EN
EN English

Advertisement

Table of Contents
loading

Related Manuals for CAME ZLJ14

Summary of Contents for CAME ZLJ14

  • Page 1 Control panel Control panel FA01082-EN for 24 V gearmotors for 24 V gearmotors ZLJ14 EN English INSTALLATION MANUAL...
  • Page 2 Any other use is dangerous. CAME S.p.A. is not liable for any damage caused by improper, wrongful and unreasonable use. • Before installing the control panel, make sure that the gui-...
  • Page 3 will cease to be effective. • All maintained-action switches that are connected to the control panel must be positioned so that the maneuvering area is completely visible from the switches, yet far enough away from any moving parts. • Make sure that the operator has been properly adjusted and that any associated safety and protection devices, as well as the gearmotor's manual release, are working properly.
  • Page 4 All wiring connections are quick-fuse protected. Intended use Model Operator ZLJ14 AMICO - AXO - F4000 - FAST - FERNI - FROG - FROG J - MYTO Any installation and/or use other than that specified in this manual is forbidden. Technical data...
  • Page 5 Description of parts 14. Encoder terminals Transformer power on warning LED 15. Gearmotor terminals Display 16. Power supply terminals Memory roll card slot 17. Line fuse Programming buttons 18. Control-board fuse Programming warning LED 19. Electric-lock fuse Display-brightness adjusting trimmer 20.

  • Page 6: Installation

    Dimensions APRE CHIUDE INSTALLATION Cable type and minimum section cable length Connection < 20 m 20 < 30 m Control panel power-supply 3G x 1.5 mm 3G x 2.5 mm Motor power supply see the corresponding operator-manuals Signaling devices 2 x 0.5 mm2 Command and control devices 2 x 0.5 mm2 Safety devices (photocells)
  • Page 7 Tools and materials Make sure you have all the tools and materials you will need for installing in total safety and in compliance with applicable regulations. The figure shows some of the equipment installers will need. Fastening the control panel Fasten the control panel in a protected area;...

  • Page 8: Electrical Connections

    ELECTRICAL CONNECTIONS Input voltage Terminal board for 24 V AC / DC accessories - Maximum power: 50 W Connecting the electric lock (12V-15W max) 230 V AC 50/60 Hz Connecting the gearmotors that have no limit switch M1 - Gearmotor with delayed opening.
  • Page 9 Connecting ENCODER-fitted gearmotors M1 - Gearmotor with delayed opening. AMICO - AXO FROG J - MYTO M N ENC 2 FA FC M N ENC + E - M1 - Gearmotor with delayed opening. F4000 - FAST FERNI - FROG 1 = White 2 = Brown 3 = Green...
  • Page 10 Command and control devices Stop button (N.C. contact). - For commanding the gate to stop while excluding the automatic-closing time cycle. To resume movement, press a button on the control or the transmitter button. & If unused, disable the contact in the [FUNCTIONS] menu → [Total Stop].

  • Page 11: Safety Devices

    Safety devices Delta Dir/DeltaS 10 11 TS E ES 1 2 3 3P 4 5 7 CX CY CZ Photocells connections (N.C. contact) - See [FUNCTIONS] menu → [input CX], [input CY] or [input CZ] for associating an operating mode to each input. &...
  • Page 12 ENABLING THE RADIO CONTROL Antenna and AF radiofrequency card Connect the RG58 antenna-cable to the corresponding terminals. Fit the radio-frequency card into the slot on the control board AFTER CUTTING OFF THE MAINS POWER SUPPLY. N.B.: The control board recognizes the radiofrequency card only when it is powered up.
  • Page 13 PROGRAMMING Description of programming commands The key is for: These symbols / , show - entering menus; the active line that can be - confirming or memorizing set values. browsed and/or edited. , The key is for: - exiting menus; - cancelling changes.
  • Page 14 & IMPORTANT! Start programming from [Motor Type], [No. of Motors], [Total Stop] window on the [FUNCTIONS] menu and [Gate-Swing Calibration] window on the [ENCODER] menu. Menu 1st level Menu 2nd level Options Default [LANGUAGE] [Italiano] / [English] / [Français] / [Deutsch] / [Español] / [English] [Portugues euro]/[Portugues bras] [FUNCTIONS]...
  • Page 15 Menu 1st level Menu 2nd level Options Default [CY input] [Disabled] / [C1] / [C2] / [C3] / [C4] / [C7] / [C8] [C3] See [CX Input] [CZ input] [Disabled] / [C1] / [C2] / [C3] / [C4] / [C7] / [C8] [C2] See [CX Input] [Cl.
  • Page 16 Menu 1st level Menu 2nd level Options Default Adjusting the maneuvering speed, calculated as a percentage. [Slow Down Spd. [10%] …… [50%] [50%] Adjusting the slow-down speed, calculated as a percentage. [Soft Start] [Disabled] / [Enabled] [Disabled] After each opening and closing command, the leaves start at slowed down speed for a few seconds.
  • Page 17 Menu 1st level Menu 2nd level Options Default Setting the slow-down starting point before the closing limit-switch, calculated as a percentage of the complete gate swing. & This function only appears if the [Enc. Slodwn.] function in the [ENCODER] menu. [1%] ……...
  • Page 18 [Number of Runs] View the number of completed maneuvers. [Open. Msg.] WWW.CAME.IT View opening message. To edit the text, press ENTER. Use ENTER to move the cursor forward, and ESC to move the cursor backwards and / to select the letter or figure.
  • Page 20 Entering a new user 1. From the [USERS] menu, select 2. Select [Confirm?(yes)] and press 3. Select the function to associate to [New User]. Press ENTER to confirm. ENTER to confirm. users. Press ENTER to confirm... 4..you will be asked to enter a 5.
  • Page 21 Edit code 3..you will be asked to enter a code 1. From the [USERS] menu, select 2. Select the user whose code you representing a transmitter, swipe card [Edit Code]. Press ENTER to confirm. want to edit and press ENTER. or transponder.
  • Page 22 Gate-swing calibration ⚠ Before calibrating the gate-swing, check that the maneuvering area is free from any obstruction and that there are both opening and closing mechanical gate-stops. ⚠ The mechanical gate-stops are obligatory. Important! During the calibration, all safety devices will be disabled except for the PARTIAL STOP one. 1.

  • Page 23: Error Message

    ERROR MESSAGE System Meaning [Encoder - ERROR], [Error!] Broken encoder or wrong connection. [Safety test - ERROR] Safety devices malfunctioning. [Limit-switch - ERROR] Malfunctioning limit-switch contacts [Operating Time - ERROR] Insufficient operating time [Safety - STOP], [C1], [C3], [C4], Malfunctioning safety devices or wrong connection [C7] or [C8] GRAPHIC DIAGRAM OF THE ENCODER'S FUNCTIONS &...

  • Page 24: Final Operations

    DISPOSE OF RESPONSIBLY! REFERENCE REGULATIONS CAME SpA declares that this product complies with the current directives at the time it is manufactured. The contents of this manual may change, at any time, and without notice. CAME S.p.A.

Table of Contents