Mobile Video Recorder Installation Guide TABLE OF CONTENTS Chapter 1 Panel Introduction ................................. 7 1.1 Front Panel ....................................7 1.2 Rear Panel ....................................8 Chapter 2 Installation and Connections ............................10 2.1 Environment ....................................10 2.2 Install HDD ....................................10 2.3 Install SIM Card ..................................14 2.4 Install SD Card ..................................15 2.5 Install Antenna ..................................15 2.6 Power Cord Wiring...................................
Page 3
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
Page 4
Mobile Video Recorder Installation Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 5
Mobile Video Recorder Installation Guide radiator and your body EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union.
Page 6
Mobile Video Recorder Installation Guide Applicable Models This manual is applicable to the models listed in the following table. Series Model DS-MP5504 DS-MP5504/GW DS-MP5504/GW/WI DS-MP5504 DS-MP5504/GW/WI58 DS-MP5504/GLF DS-MP5504/GLF/WI58 Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement...
Page 7
Mobile Video Recorder Installation Guide Safety Instructions Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
Mobile Video Recorder Installation Guide Chapter 1 Panel Introduction 1.1 Front Panel Figure 1-1 Front Panel Table 1-1 Interface Description No. Name Description Dummy HDD lock Lock/Unlock the dummy HDD. USB interface USB 2.0 interface. IR receiver IR receiver for remote control. Power indicator ...
Mobile Video Recorder Installation Guide Chapter 2 Installation and Connections Device pictures in following sections are only for reference. In condition that product pictures conflict the real device, the later prevails. 2.1 Environment To ensure the device can ventilate well, find a position with enough space. Recommended installation space is shown in Figure 2-1.
Page 12
Mobile Video Recorder Installation Guide Screws (delivered with device). Figure 2-2 Tools Purpose: Perform the following steps to install the HDD on the device. Figures in following steps are only for reference. Step 1 Insert the key and turn counterclockwise to unlock dummy HDD. Step 2 Unfasten the two screws of dummy HDD and pull dummy HDD out of device.
Page 13
Mobile Video Recorder Installation Guide Figure 2-4 Take Apart Dummy HDD Step 4 Place the first HDD into the dummy HDD, with the PCB facing down. Figure 2-5 Place HDD Step 5 Push the HDD along the direction shown in Figure 2-6 to connect HDD with socket of dummy HDD.
Page 14
Mobile Video Recorder Installation Guide Step 6 Use four sunk screws to fix HDD with dummy HDD. Figure 2-7 Fix HDD Step 7 Repeat step 4 to 6 to install the secondary HDD in the other socket of dummy HDD. Figure 2-8 Install the Other HDD Step 8 Reassemble the dummy HDD.
Mobile Video Recorder Installation Guide Figure 2-9 Reassemble Dummy HDD Step 9 Plug the dummy HDD back to the device and then tighten the screws clockwise. Step 10 Turn the key clockwise to lock dummy HDD. 2.3 Install SIM Card Purpose: Pluggable 3G/4G wireless communication module is designed for the device and you should install the SIM card to realize the wireless communication function.
Mobile Video Recorder Installation Guide Step 4 Press the yellow button on the 3G/4G slot and then pull the SIM card tray out. Step 5 Place the SIM card on SIM card tray. Step 6 Insert the SIM card tray back to SIM card slot. Step 7 Install the 3G/4G module back to the device and tighten the set screw.
Page 17
Mobile Video Recorder Installation Guide Table 2-1 Antenna Interface Interface Corresponding Antenna M-ANT Main 3G/4G antenna Aux Wi-Fi antenna WIFI Main Wi-Fi antenna Positioning antenna GNSS/ Place antenna vertically with its signal receiving end facing upward. If the cable is too long, you can roll them up to prevent signal receiving from being affected. ...
Mobile Video Recorder Installation Guide 2.6 Power Cord Wiring In order to ensure the safety of your automobile and device, a fuse is required for wiring of automobile power and device power. Do not connect the power cord to the device before all the cables are connected. 2.6.1 Shutdown Delay Purpose: The device starts up when your automobile ignites and shuts down after automobile is off.
Mobile Video Recorder Installation Guide Device Automobile Power System DC IN Wiring of Device Point of Connection Automobile Power Switch Positive Pole Negative Pole Automobile Ignition Switch Automobile Battery Figure 2-17 Shutdown Delay Please contact the automobile manufacturer for the connection information of starting switch.
Mobile Video Recorder Installation Guide Device Automobile Power System DC IN Wiring of Device Point of Connection Automobile Power Switch Positive Pole Negative Pole Automobile Battery Figure 2-19 Scheduled Shutdown 2.7 Alarm Input/Output Connection 2.7.1 Alarm Input Connection The device adopts the high/low-level electrical signals triggering (high level: 6 to 36 VDC; low level: 0 to 5 VDC) to realize alarm input.
Mobile Video Recorder Installation Guide GND Power JQC-3FG Output Relay (10 A/250 VAC) Load Relay Relay ~ 220 VAC Output Output Live Neutral Alarm Powered by Direct Current Alarm Powered by Alternating Current Figure 2-21 Alarm Output Connection 2.8 Sensor-in Wiring Step 1 Connect the delivered extension cable to I/O interface.
Page 22
Mobile Video Recorder Installation Guide UD10342B...
Need help?
Do you have a question about the DS-MP5504 Series and is the answer not in the manual?
Questions and answers