Fcc Statement; Fcc Radiation Exposure Statement - Netis DL4310 Quick Installation Manual

Appendix

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful
interference in a residential installation. This equipment generatesuses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On
the exterior of the cabinet of this equipment is a label that contains, among other information, the FCC
Registration Number and Ringer Equivalence Number (REN) for this equipment. A product identifier in
the format US: SX5DL01BDL4310R (for DL4310, DL4310D), SX5DL01BDL4311R2 (for DL4311 V2,
DL4311D V2), SX5DL01BDL4311R1 (for DL4311 V3, DL4311D V3), SX5DL01BDL4312R(for DL4312,
DL4312D), SX5DL01BDL4322R(for DL4322 V2, DL4322D V2), SX5DL01BDL4322R1(for DL4322 V3,
DL4322D V3), SX5DL01BDL4323R(for DL4323, DL4323D). If requested, this number must be provided
to the telephone company.
FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or premises wiring using a compatible modular jack
that is Part 68 compliant. See Installation Instructions for details. The REN is used to determine the
quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line
may result in the devices not ringing in response to an incoming call. Typically, the sum of RENs should
not exceed five (5.0). To be certain of the number of devices that may be connected to a line (as
determined by the total RENs) contact the local telephone company. If this equipment causes harm to the
telephone network, the telephone company will notify you in advance that temporary discontinuance of
service may be required. But if advance notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary. The telephone company may make changes to its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this happens, the telephone
company will provide advance notice so you can make the necessary modifications to maintain
uninterrupted service. For technical support, contact netis Systems USA Corp. at 8541 Gale Avenue, City
of Industry, CA 91748or call TEL: 626-810-5866. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect the equipment until the problem is
resolved.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it
also complies with Part 15 of the FCC RF Rules. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device complies with Part 15& 68 of the FCC Rules. Operation is
conditions: (1) this device may not cause
interference received, including interference that may cause undesired operation.
§ 15.105 Information to the user.
For a Class B digital device or peripheral, the instructions furnished the user shall include the following
or similar statement, placed in a prominent location in the text of the manual:
§ 15.19 Labelling requirements.
(a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification
shall be labelled as follows:
(1) Receivers associated with the operation of a licensed radio service, e.g., FM broadcast under part 73
of this chapter, land mobile operation under part 90, etc., shall bear the following statement in a
conspicuous location on the device:
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this
device does not cause harmful interference.
(2) A stand-alone cable input selector switch, shall bear the following statement in a conspicuous location
on the device:
This device is verified to comply with part 15 of the FCC Rules for use with cable television service.
(3) All other devices shall bear the following statement in a conspicuous location on the device:
§ 15.21 Information to user.
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user
that changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment. In cases where the manual is provided only in a form other
than paper, such as on a computer disk or over the Internet, the information required by this section may
be included in the manual in that alternative form,
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
harmful interference, and (2) this device must accept any
subject to the following two