Page 1
EVASION BUMP SUPAIR-VLD PARC ALTAÏS 34 RUE ADRASTÉE User’s manual 74650 ANNECY CHAVANOD FRANCE 45°54.024’N / 06°04.725’ E English version RCS 387956790 Revision Indice: 10/07/2018...
Page 2
We trust that you will find this user’s manual comprehensive, explicit and hopefully pleasant to read. We advise you to read it carefully ! On our website www.supair.com, you will find the last up to date information about this product. If you have any further questions, feel free to ask one of our retailers.
Reserve parachute installation in the pocket. Recycling Installing the reserve parachute in its pocket. Environmental friendly practices Position setting Warranty Leaning angle setting Disclaimer Shoulders’ straps adjustments. Pilot’s gear Chest strap adjustment. Service Book Flight behavior Pre-Flight control SUPAIR | EVASION BUMP | page 3...
Introduction Welcome to the tandem world. With the EVASION BUMP, you are equipped with a tandem harness designed with an integrated reserve parachute pocket and an BUMPAIR pro- tection. This harness is targeting intensive professional use. The ergonomy is classic with a wooden seatplate whose V-shape enables a very ergonomic position with the passenger.
EN 1651 - LTF Flight : tandem (Pilot- Passenger) Pilot Flight : acrobatic flying Take-off : Winching Quick-out carabiners compatibility This harness is delivered with two 45 mm Biners ( 138 g. for the set ). SUPAIR | EVASION BUMP | page 5...
Place the handle inside the middle webbing loop and make a lark’s Fasten tightly the lark’s head knot and verify the solidity of the link. head knot with the handle. The handle must be connected to the central loop. SUPAIR | EVASION BUMP | page 9...
Push the risers the grommet. through the guiding sleeves ( the risers must be located behind the parachute ). SUPAIR | EVASION BUMP | page 10...
Page 11
Upon setup completion, conduct an extraction sequence during a hang-test to verify that all works properly before duplicating the installation procedure again... SUPAIR | EVASION BUMP | page 11...
Page 12
Install the risers inside the lateral guiding sleeve. main hooking location ), with the maillon rapide The risers come out of each strap guide. trapeze stainless steel 6 mm + the flexible elastic rings. Parachute riser. Pilot Passenger. Pilot Passenger. SUPAIR | EVASION BUMP | page 12...
You must find the correct tension between the side and shoulder straps adjustments. tighten Chest strap adjustment. To adjust correctly during a hang-test. The chest-strap tensioning/loosening as little effect on the wing’s incidence while weight-shifting. SUPAIR | EVASION BUMP | page 14...
• Fully close the leg straps, Safe-T-bar and chest strap buckles.. • Takeoff maintaining a vertical posture and push yourself inside the harness but only once away from the ridge. Do not let go the brakes when close to the terrain. SUPAIR | EVASION BUMP | page 15...
During high wind speed landings, turnaround and face the wing as soon as ground contact is made and move toward the wing while braking symmetrically to deflate it. Do not land in a seated position as it is dangerous. SUPAIR | EVASION BUMP | page 16...
Page 17
- Ascertain parachute deployment functionality by pulling the handle to activate a clean POD extraction sequence. - Inspect the harness for wear and tear. Annual check - An annual deployment and repacking of the reserve parachute must be conducted by competent and certified personnel. SUPAIR | EVASION BUMP | page 17...
• The AIRBAG’s integrity ( especially after a strong impact ), in other words, no holes, tears or rips. The threads and fabric used to manufacture the EVASION BUMP were specifically selected for their quality and resilient capacities. However in particular instances such as long term UV exposure abrasion, contact with damaging chemicals, general wear and tear, the harness will need to be inspected at a professional certified repair facility.
If you estimate that your EVASION BUMP has reached the end of it life-span, you can separate plastics from metals and dispose of them according to your community recycling rules. As for the fabric itself contact your local authorities to find out how to proceed to discard...
Your harness protection CE conformity labeling is certified by the following laboratory : CRITT Sport Loisirs nr. 0501, Z.A. du Sanital, 21 Rue Albert Einstein, 86100 Chatellerault – FRANCE SUPAIR | EVASION BUMP | page 20...
User manual | EVASION BUMP Service Book This page will help you to record all the life stages of your EVASION BUMP harness. Serial number : Care Purchase date Care Resale Resale Owner’s name date date Name and stamp of the shop Workshop’s name/ Buyer’s name...
Need help?
Do you have a question about the EVASION BUMP and is the answer not in the manual?
Questions and answers