Sercomm NA502S User Manual

Sercomm NA502S User Manual

Multiple rf home gateway

Advertisement

NA502S
Multiple RF Home Gate-
way
User Guide
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NA502S and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sercomm NA502S

  • Page 1 NA502S Multiple RF Home Gate- User Guide...
  • Page 2: Table Of Contents

    Table of Contents CHAPTER 1 INTRODUCTION ....................1 Package Contents ......................1 Features ..........................1 LEDs ........................... 2 CHAPTER 2 INITIAL INSTALLATION................5 Requirements ........................5 Procedure ........................... 5 SIM Card Installation ....................... 7 CHAPTER 3 CONFIGURATION ................... 8 Configuration ........................8 APPENDIX A SPECIFICATIONS ..................
  • Page 3: Chapter 1 Introduction

    Chapter 1 Introduction This Chapter provides an overview of the Multiple RF Home Gateway's fea- tures and capabilities. Congratulations on the purchase of your new Multiple RF Home Gateway. The Multiple RF Home Gateway is a consumer electronic device, which is designed to bridge all appliances of your home, from IP cameras to sensors, and allow you to monitor and manage them over the Internet.
  • Page 4: Leds

    LEDs Front Panel The Multiple RF Home Gateway has 9 LEDs. POWER (Green) On - Power On/Normal Operation  Off - Power Off  Flashing - Rebooting.  WiFi On - WPS mode is selected.  (Green) On (5 seconds) - WiFi connection is established. ...
  • Page 5 (Green) On (5 seconds) - Bluetooth sensor added or synchronization is  successful. Off - Bluetooth module is in idle mode.  Flashing - Bluetooth module is in active mode.  On - 3G connection established.  (Green) Off - No active 3G connection. ...
  • Page 6 Sync Button After selecting the RF mode, push the Sync button to synchronize  the gateway and sensors. Push the Sync button for three seconds again to stop the synchroni-  zation process if needed. Reset This button has two (2) functions: ...
  • Page 7: Chapter 2 Initial Installation

    Chapter 2 Initial Installation This Chapter covers the software installation of the Multiple RF Home Gate- way. Requirements  Use a standard 10/100/1000 BaseT network (UTP) cable with RJ45 connector. Procedure 1. Choose an Installation Site Select a suitable place to install the Multiple RF Home Gateway. 2.
  • Page 8 3. Attach the back cover to the device with the screws. 3. Connect LAN Cable Use a standard LAN cable to connect the device to the Ethernet port on the Multiple RF Home Gateway. 4. Power Up Connect the supplied power adapter to the Multiple RF Home Gateway. Use only the pow- er adapter provided.
  • Page 9: Sim Card Installation

    Initial Installation SIM Card Installation Ensured the device is powered off. Remove the screws on the back cover of the device with a screwdriver. Find the location of the SIM card tray. Push the SIM card cover upward. Insert the SIM card into the slot. Make sure the SIM card is installed correctly. Put the SIM card cover back.
  • Page 10: Chapter 3 Configuration

    Chapter 3 Configuration This Chapter provides Setup details of the Gateway. Configuration The Multiple RF Home Gateway can offer customers with seamless communication between devices and clouds while at home or away. This gateway is designed to provide complete connectivity with all certified devices including cameras, security systems and WiFi/ZigBee/Z- Wave/Bluetooth/3G devices.
  • Page 11: Appendix A Specifications

    Appendix A Specifications Multiple RF Home Gateway Model Multiple RF Home Gateway Dimensions 222mm(W) * 148mm(D) * 48mm(H) Operating Temperature 0 C to 40 C Buttons Network Protocol: TCP/IP Network Interface: 1 * 10/100/1000BaseT (RJ45) LAN connection LEDs Battery 2S1P 18650 Battery USB Port 1 * USB 2.0 Type A Port SIM Card Slot...
  • Page 12 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Table of Contents

Save PDF