Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Intercel Smart SAM3W
Summary of Contents for Intercel Smart SAM3W
- Page 1 Smart SAM3W User Guide V1.1 Smart SAM3W User Guide Ver1.1...
- Page 2 Smart SAM3W User Guide V1.1 Revision History Version Modified By Date Description 11/02/2013 Initial version 09/10/2013 Added new packaging Ver1.1...
-
Page 3: Table Of Contents
Smart SAM3W User Guide V1.1 Contents Introduction ................................2 General Features ...............................3 Safety Precautions .............................4 Radio Frequency Exposure - SAR ........................5 WEEE Directive 2002/96/EC, Disposal Of Old Electronic Equipment ............6 Packaging ................................7 6.1 Contents ................................7 6.2 Packaging Box ..............................7 6.3 Production Label ..............................8 Functionality ................................9... -
Page 4: Introduction
GSM, GPRS, UMTS and HSPA connectivity. The Smart SAM3W TCP/IP stack can be turned on/off using an AT command. The Smart SAM3W is designed for both mobile and fixed M2M applications. It has an RJ45 socket for input voltage and the serial RS232 signals, an FME-male for antenna connection, a SIM holder and an LED indicator. -
Page 5: General Features
Smart SAM3W User Guide V1.1 2 General Features Quad-band GSM/GPRS 850/900/1800/1900MHz Dual-band UMTS/HSPA 850/2100MHz (The other option is 900/2100MHz) GPRS class B/Class 10 HSPA Upload 1.8Mbps, down load 3.6Mbps CSD supported Ver1.1... -
Page 6: Safety Precautions
Smart SAM3W User Guide V1.1 3 Safety Precautions The following safety precautions must be observed whenever the Smart SAM3W modem is in operation or in service. Failure to comply with these precautions violates the safety standards of the design, manufacture... -
Page 7: Radio Frequency Exposure - Sar
This is because the transceiver is designed to use minimum power to connect to the network. The Smart SAM3W modem is approved to use in applications where the antenna is placed more than 21cm from the body. -
Page 8: Weee Directive 2002/96/Ec, Disposal Of Old Electronic Equipment
It must be placed at an appropriate collection point for the recycling of electrical and electronic equipments. By ensuring the correct disposal of this equipment, it will help the environment and human’s health. The recycling will help to conserve the natural resources. The Smart SAM3W product is RoHS compliant Ver1.1... -
Page 9: Packaging
The Data cable is 2m long The Label size is 50mm x 33mm The Power supply is available on request. It is recommended that the Smart SAM3W is powered using a 12Vdc/1A power supply. Antennas are also available on request. Please make sure the correct antenna is used to get optimised performance from the Smart SAM3W Ver1.1... -
Page 10: Production Label
352679010 049570 : Intercel Pty Ltd Made by : ASSSMRTS3W Part number The production part number is located at the back of the Smart SAM3W, which includes: The product model The software Version The Hardware Version The IMEI number The manufacturer The part number Ver1.1... -
Page 11: Functionality
7 Functionality 7.1 General The Smart SAM3W modem consists of an RJ45 socket for serial port and input power, an FME male antenna connector and a SIM holder. The LED indicator, located next to the SIM holder, indicates the Smart SAM3W operating status. -
Page 12: Rj45 Socket
Input voltage 5Vdc - 32Vdc Data Carrier Detect DTR/RI Data terminal Ready/Ring Indicator Common Ground Serial Data out of the Smart SAM3W Serial Data into the Smart SAM3W Clear to Send Ready to Send 7.3 FME-Male 50Ω Antenna Connector The FME male antenna connector is a 50Ω impedance antenna connector. The antenna used for the Smart SAM3W must have 50Ω... -
Page 13: Data Cable
The data cable is 2m long. It consists of an RJ45 plug, a DB9-female connector and a 2-wire input power. Signals RJ45 Description Data Carrier Detect Serial Data out of the Smart SAM3W Serial Data into the Smart SAM3W Not used Common Ground Ready to Send... -
Page 14: Electrical Characteristics
Smart SAM3W User Guide V1.1 8 Electrical Characteristics 8.1 Power Consumption (TBC) Idle mode <0.24W 1W – 1.6W GSM/GPRS mode 1W – 2W UMTS/HSPA mode Absolute Peak current 600mA @ 12V 8.2 Receive Sensitivity Band Typical Rx Sensitivity Maximum Rx Sensitivity... -
Page 15: Main Antenna Specifications
Smart SAM3W User Guide V1.1 8.4 Main Antenna Specifications Max cable loss 0.5dBm 50Ω Impedance Max allowed VSWR The maximum antenna gain recommended, for consideration against RF exposure and ERP/EIRP limits, is: In Cellular band : 5dBi In PCS band : 4dBi 8.5 Environmental Characteristics... -
Page 16: Smart Sam3W Tcp/Ip Operation
(SAMMODE=0) or as a smart 3G modem. With the SAMMODE=1 or 2 the TCP/IP stack will take full control of the Smart SAM3W and stay in GSM mode when SAMMODE=2 to allows the modem to receive GSM data call (CSD) or automatically connect to PSD network when SAMMODE=1. Both UDP and TCP are supported,... -
Page 17: Tcp/Ip At$ Commands
Smart SAM3W User Guide V1.1 9.3 TCP/IP AT$ Commands Communications parameters are stored in Flash using AT$PARAMETERS. Parameters are defined as: APN=Access Point Name USERNAME=Username that may required with GPRS login PASSWORD=Password that may required with GPRS login LTCPPORT=Local TCP listening port... - Page 18 Smart SAM3W User Guide V1.1 All parameters can be programmed all at once. AT$PARAMETERS=APN=telstra.extranet,USERNAME=intercel,PASSWORD=mach,LTCPPORT=10000,RT CPIP=203.45.1.236,RTCPPORT=10000,TCPMODE=,LUDPPORT=20000,RUDPIP=203.45.1.236,RUDPPO RT=20000,POLLPERIOD=60,SBREAKTIME=100,MBREAKTIME=5,BAUDRATE=115200,DATALEN=8,PAR ITY=NONE,SAMMODE=0 Saved parameters to flash... Or a few parameters or one at a time. AT$PARAMETERS=APN=telstra.extranet,USERNAME=intercel,PASSWORD=mach Saved parameters to flash... AT$PARAMETERS=LTCPPORT=10000,RTCPIP=203.45.1.236,RTCPPORT=10000,TCPMODE=,LUDPPO RT=20000,RUDPIP=203.45.1.236,RUDPPORT=20000 Saved parameters to flash...
- Page 19 Smart SAM3W User Guide V1.1 AT$PARAMETERS? $PARAMETERS: APN: telstra.extranet USERNAME: intercel PASSWORD: mach LTCPPORT: 10000 RTCPIP: 203.45.1.236 RTCPPORT: 10000 TCPMODE: 0 LUDPPORT: 20000 RUDPIP: 203.45.1.236 RUDPPORT: 20000 BAUDRATE: 115200 DATALEN: 8 PARITY: NONE POLLPERIOD: 60 SBREAKTIME: 100 MBREAKTIME: 5 SAMMODE: 0...
-
Page 20: Csd Call Escape Sequence
Smart SAM3W User Guide V1.1 AT$RESET SAM Reset... 9.4 CSD Call Escape Sequence During CSD call to the Smart SAM3W modem, send three consecutive EscEscEsc hex number sequence 0x1B 0x1B 0x1B to switch the modem between data mode and remote AT commands mode. Ver1.1... -
Page 21: Firmware Upgrade
Smart SAM3W User Guide V1.1 10 Firmware Upgrade 10.1 Firmware Upgrade For The 3G Module The module’s firmware can be upgraded over the USB port using the dedicated Upgrade Program running on PC. The Module’s driver must be installed on the PC beforehand. - Page 22 Smart SAM3W User Guide V1.1 Notes Ver1.1...
- Page 23 Should Buyer purchase or use intercel...