Global FREEFIT Installation Manual & Operating Instructions page 8

GLOBAL Contract
FREEFIT INSTALLATION GUIDE
Using Controls
Wheel Controls
How to set memory:
Calibrate
Run/Drive the table to the position you will store,
sitting or standing.
If the height reading displays incorrect height, the
(This device have 5 memories position memories)
height from the table top needs to be
calibrated.
Press menu button + "stand" icon 1 time to come
Measure the distance between the floor and the top
to set memory menu.
of the table top.
Press and hold M button for at least 8
seconds...
Use arrow up and down to navigate to set memory
setting. ...until three dashes are displayed
---
Release Release the M button
Use the Up or Down button to
CAL
navigate to CAL (Calibrate)
Select by pressing the M button
Press Menu/Enter, and the value are stored.
Change the current height reading by using
or
the Up or Down button to the measured height
Store the current height reading and return to
Menu by pressing the M button
The display confirm by flashing 3 times and then
returns to normal mode.
Units
Calibrate:
Change between metric or imperial units
Measure the distance between the floor and the top
of the table sheet.
Press menu button + "stand" icon 2 times to come
to calibrate menu.
Press and hold M button for at least 8
seconds...
...until three dashes are displayed
---
CAL
Release Release the M button
Use the Up or Down button to navigate to
Un (Units).
Press Menu/Enter to confirm
Select by pressing the M button
CM OR " Choose CM (centimeter) or " (inch) with the Up
or Down button
Adjust the figures to the selected value with the
Select value and return to Menu by pressing
arrows up or down.
the M button
28
Press Menu/Enter, and the value are stored.
8
Upper Limit
Set an Upper Limit when planning over-head storage
---
Release
U . L .
1
5
Performing a Forced Reset
If Standard Reset (page 6) does not initiate
a reset, perform a Forced Reset
---
Release
RES
0
.
Upper limit:
Set the upper limit if there are limited
space in height.
Press menu button + "stand" icon 3
times to come to set memory menu.
Press and hold M button for at least 8
seconds...
...until three dashes are displayed
UL
Release the M button
Press Menu/Enter to confirm.
Use the Up or Down button to
navigate to U.L. (Upper Limit)
Select by pressing the M button
Adjust the figures to the chosen level
Calibrate Upper Limit by using the Up or
or
with the arrows up or down. Down buttons
Select value and return to Menu by pressing
the M button
50 0
.
Press Menu/Enter, and the value are
stored.
Please note that the figures count
from the table top surface.
Lower limit:
Set the lower limit if there are device/
Press and hold M button for at least 8
equipment which could create a risk
seconds...
of pinching or risk for table damages.
...until three dashes are displayed
Press menu button + "stand" icon 4
times to come to set memory menu.
Release the M button
Use the Up or Down button to navigate to
RES. (Reset)
LL
Select by pressing the M button
Activate Reset/Homing by
pressing the Down button
Press Menu/Enter to confirm
Adjust the figures to the chosen level
with the arrows up or down.
27 5
.
Press Menu/Enter, and the value are
stored.
Please note that the figures count from
the table top surface/ calibrated level.
• August 2014
Units:
Lower Limit
Choose between metric or imperial
system.
Set a Lower Limit when planning storage under the table
Press menu button + "stand" icon 5
times to come to set memory menu.
Press and hold M button for at least 8
seconds...
...until three dashes are displayed UN
---
Release Release the M button
Press Menu/Enter to confirm.
Use the Up or Down button to navigate to L.L
L . L .
(Lower Limit)
Select by pressing the M button
Adjust the figures to the chosen level
Calibrate Lower Limit by using the Up or
with the arrows up or down.
or
Down button
Select value and return to Menu by pressing
the M button
Press Menu/Enter, and the value are
stored.
Reset Away:
Software Version
Press menu button + "stand" icon 6
times to come to set memory menu.
Display Software Version
RES
Press Menu/Enter, and the value are Press and hold M button for at least 8
seconds...
stored.
...until three dashes are displayed
---
Release Release the M button
Use the Up or Down button to navigate to SOF
Press 'down" and hold until the columns
SOF
(Software Version)
have gone to the lowest position.
Select by pressing the M button
Do reset if any parts have been changed
Software Version Software Version will appear on the display
of if you discover interference between
displayed
the columns.
Return to Menu by pressing the M button
Error codes:
3
1. Hard stop
2. Back off
3. Soft top
4. Waiting for button
5. Waiting for button release.
6. Motor lost
Overheating. Thermometer flashing,
wait 10 minutes for motor cooling.
globalcontract.com •Page
globalfurnituregroup.com
9