Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bona Bona Belt AMO110001.3
Summary of Contents for Bona Bona Belt AMO110001.3
- Page 1 Bona Belt AMO110001.3 - AMO110000.3 Operating Manual...
- Page 2 If anything is unclear, turn to your reseller with confidence or directly to Bona AB. Keep this manual for future reference. This manual is an English translation of the original version in Italian. For a new manual contact:...
-
Page 3: Table Of Contents
Setting the drum lever Setting the height of the handle shaft Changing the sanding drum Dust collection Routine Maintenance Troubleshooting (for the user) Safety Regulation when using Bona Belt Service, Maintenance and Spare Parts Service and maintenance Spare Parts Warranty Declaration of Conformity... -
Page 4: Machine Specifications
Machine Specifications Bona Belt Manual Motor Type: 1 phase Voltage (±10%): 230 V Frequency: 50 Hz Power: 2.2 kW Rated Current: 12.9 A Recommended fuses: Class C 16 A Insulation class: Protection class: IP54 Abrasive Drum Speed: 1750 rpm normal load... -
Page 5: Machine Symbols Key
Read and follow all 'CAUTION' alerts on this machine or in this manual. Failure to read the Bona Edge machine manual before operating, adjusting or performing maintenance operations on the machine could cause injury or damage to persons or objects. - Page 6 Operator Safety (Cont.) Bona Belt Manual Sanding may create an explosive environment. Cigarettes, cigars, pipes, lighters, pilot flames, or any other source of fire may create an explosion, if lit during sanding operations. All sources of ignition should be removed entirely from the work area.
-
Page 7: Storage
Operator Safety (Cont.) Performing maintenance or replacing the dust bag may cause injury to the operator or people nearby, if the machine is connected to the power supply. Always unplug the machine when not in use. DO NOT use solvents or other flammable products to clean this machine. Dry use only. -
Page 8: Introduction
If a situation arises which has not been described in this manual, contact your distributor or Bona Representative. The Bona Belt wood flooring sander is suitable for the dry sanding of wood floors. Any other use without the consent of the manufacturer is prohibited. -
Page 9: Commencing Operation
Commencing Operation Instructions for assembly Assembly a new machine Push together the handle shaft with the shaft holder. Screw and tighten the locking wheel. Put together the upper and lower control rod and pass the sliding Lift the control lever to the uppermost position. sleeve over the lower control rod.. -
Page 10: Dismantling The Machine
Commencing Operation (Cont.) Bona Belt Manual Instructions for assembly (cont.) If the machine has been disassembled before transport then assemble the motor as follows: Grab hold of the motor's carry handle. Place the motor on the Roll on and tighten the driving belt using the eccentric tightener. Lift machine frame and fasten the motor's hinge in the rear holder. -
Page 11: Instructions For Electrical Connection
Commencing Operation (Cont.) Instructions for electrical connection This machine only operates with the voltage and frequency shown on the machine data plate. Before connecting the cable to the power supply ensure the correct voltage and frequency are available. DO NOT expose the machine to rain. This machine is intended for dry use only. Keep the machine in a dry building and DO NOT use it in damp or wet places. -
Page 12: Instruction On Removing Sawdust Generated During Use
Commencing Operation (Cont.) Bona Belt Manual Instruction on removing sawdust generated during use Sawdust can ignite spontaneously and cause injury or damage. It must be disposed of appropriately. Always empty the sawdust into metal containers which are located outside the building. -
Page 13: Instructions On Correct Machine Use
Instructions on Correct Machine Use Read this manual carefully and become familiar with the machine. The equipment is suitable for industrial use (e.g. in hotels, schools, hospitals, offices, factories and shops). The following information highlights particularly hazardous situations for the operator and/or machine. Understand when these conditions may be present. -
Page 14: The Machine's Field Of Application
The Machine's Field of Application Bona Belt Manual The machine is intended for sanding wooden floors, parquet flooring and cork floors. Either when the floor is newly laid and untreated or when the floor is used and treated with finishes or oil. -
Page 15: Machine Adjustment Procedures
Machine Adjustment Procedures Regulation drum pressure Using the control wheel, the drum pressure can be regulated at high, medium and low in accordance with the following: Highest position = low drum pressure ~23 kg Medium position = medium drum pressure ~27 kg Lowest position = high drum pressure ~32 kg... -
Page 16: Adjusting The Sanding Belt
Machine Adjustment Procedures (Cont.) Bona Belt Manual Changing the sanding belt (Cont.) Remove the existing belt and insert the new belt Pull the tool out directly with a tug the sanding with the arrow marking in rotation direction belt will tighten automatically. - Page 17 Machine Adjustment Procedures (Cont.) Adjusting the sanding belt (Cont.) Put on fine sanding paper (100-120). Turn the fine adjustment screw counter clockwise until it stops. Remove the plastic plug protecting the large Start the machine. adjustment screw; stick a screwdriver in the hole in the machine frame.
-
Page 18: Setting The Drum Lever
Machine Adjustment Procedures (Cont.) Bona Belt Manual Setting the drum lever When correctly set, the sanding drum grinds equally across the drum width. If this is not the case, then do the following: Loosen the lock nut on the threaded rod. -
Page 19: Changing The Sanding Drum
Machine Adjustment Procedures (Cont.) Setting the height of the handle shaft (Cont.) Put the machine backward so that it rests on the Loosen the nut that holds the control rod against the slewing tilt support. bracket using a wrench. Thread up the control rod to the corresponding Lift up the control lever. -
Page 20: Dust Collection
Remove the lock pin from the sander belt plate and lift up the belt protector. Dust collection For minimal dust discharge Bona's original dust bags shall always be used. The dust bag must be emptied when it is filled to max 1/3. -
Page 21: Routine Maintenance
Routine Maintenance Before performing any service and maintenance the power cable must be removed from the wall socket. Check that the power cable holds an area of at least: EU: 1-phase 3x2.5 mm² (ASO904014) NOTE! Before restarting, the motor must cool for 3-4 minutes. The Poly-V belts must be stretched. - Page 22 Routine Maintenance (Cont.) Bona Belt Manual Regularly clean the sanding drum, tensioning device, the hole for the tool and the machine wheel. The driving belts should be adjusted now and then using the tensioning screw so that the sanding effect is not reduced. If the sanding result still is unsatisfactory the belt tensioner device should be cleaned.
-
Page 23: Troubleshooting (For The User)
Troubleshooting (for the user) Faults Causes Solutions PROBLEM CAUSES SOLUTIONS Voltage too low Check the power supply and fuses Problem with power supply Check the breaker and condensers The machine does not start If the machine has cut off due to overload protec- Allow the machine to cool for several minutes before tion restarting... -
Page 24: Safety Regulation When Using Bona Belt
Safety Regulation when using Bona Belt Bona Belt Manual When using electrical machines basic safety regulations should always be followed in order to reduce the risk of fire, electrical accidents and personal injury. Therefore, read all of the instructions before the machine is used. Then save the instructions! - Page 25 Safety Regulation when using Bona Belt (Cont.) Remove service tools before starting the Use personal safety equipment machine. Use a P2 face mask. Use approved ear protection. Check to ensure no tools are on the machine when starting or running the machine.
-
Page 26: Service, Maintenance And Spare Parts
When you contact Bona or staff approved by Bona in the event of a fault or to order spare parts, always specify the type and serial number of your machine. This information is located on the data plate of the machine. -
Page 27: Warranty
In the event of a warranty claim, the machine or the agreed part must be returned to us or our dealer for warranty testing and for potential warranty repair or replacement. During the factory warranty period, service or repairs may only be carried out upon approval by a manager at Bona and only performed by staff at Bona AB or approved staff at Bona AB . -
Page 28: Declaration Of Conformity
Declaration of Conformity Bona Belt Manual 2006/42 EC, 2014/30 EU, 2011/65 EU, 2012/19 EU KUNZLE & TASIN S.r.l. Registered Headquarters Business Management and Production Site Via Circonvallazione Est. 2/6 Via Cajkovskij, 14 27023 Cassolnovo (PV) - Italy 20092 – Cinisello Balsamo (MI) - Italy... -
Page 29: Disposal
Disposal Smaltimento di apparecchiature da rottamare da parte di privati nell’Unione Europea. Questo simbolo che appare sul prodotto o sulla confezione indica che il prodotto non deve essere smaltito assieme ad altri rifiuti domestici. Gli utenti devono provvedere allo smaltimento delle apparecchiature da rottamare, portandole al luogo di raccolta indicato per il riciclaggio delle apparecchiature elettriche ed elettroniche. - Page 30 Additional Notes Bona Belt Manual bona.com...
- Page 31 Additional Notes...
- Page 32 2016 Edition bona.com...