Page 1
Operating Instructions Translation of the original operating instructions Tool Carrier 5500 Grizzly 5500 345 - Steering brake clutch - Brake central - Petrol engine Vanguard 19L2 Before commissioning the machine, read operating instructions and observe warnings and safety instructions! Operating Instructions No.
Machine identity card (in connector cover on the outside of Tyre air pressure the cardboard box). Open (unlocked) The completed machine identity card is to be sent back to Agria- Closed (locked) Werke. Clockwise agria- Service = contact your agria-workshop...
Designation of Parts Fig. A Fig. B agria Tool Carrier 5500 Grizzly...
Page 5
12 Pawl for F-R shifting 13 Lever for F-R shifting 14 Pawl for differential lock 15 Lever for differential lock 16 Hand lever for steering brake clutch, right 17 Pawl for parking brake 18 Lever for brake central agria Tool Carrier 5500 Grizzly...
Repair wellbeing of humans, animals and plants. The trained mechanics of your agria workshop carry out expert maintenance and repair. You should only carry out major main- tenance work and repairs on your own,...
Due use includes compliance with mowed, ensure that the engine is turned manufacturer’s instructions on opera- off. tion, maintenance and repair. Any unauthorized changes to the ma- chine render manufacturer liability null and void. agria Tool Carrier 5500 Grizzly...
Page 8
For operation in enclosed areas, ensure Never adjust the operating handles dur- that a safety distance is kept to enclo- ing work – danger! sures to prevent damage to tools. agria Tool Carrier 5500 Grizzly...
Page 9
If machine is equipped with igni- springs. tion key, remove the key. For all other Do not transport the dismounted cutter versions, remove spark plug connector. bar without protective strips. agria Tool Carrier 5500 Grizzly...
Page 10
Snow Clearing Only use original agria spare parts. All Ensure snow dozer is mounted cor- other commercial spare parts must cor- rectly! Wear slip-proof shoes.
Page 11
Read and observe enclosed instruc- tions. Before you dispose of opened and seemingly empty pressurised tins (e.g. agria Tool Carrier 5500 Grizzly...
Page 12
Do not touch mov- machiner y par ts. Wait until they have come to a complete stop. With engine run- ning, keep at a safe distance from tool carrier. agria Tool Carrier 5500 Grizzly...
Continuous operation possible: up to 30° inclination (58 %) Starter: ......Recoil starter Fuel: commercially available car petrol, octane number see engine operating instructions Fuel tank capacity: ..approx. 3.6 l Fuel consumption: ....3.1 l/h agria Tool Carrier 5500 Grizzly...
3. Devices and Operating Elements The tool carrier agria 5500 Grizzly is a base power machine and is always op- erated with an implement mounted. Therefore, the machine is suited for all common applications in farming and for- estry, as well as for winter service.
Do not fasten safety lever. The safety lever also serves to switch off in an emergency. In an emergency release the safety le- ver for fast engine switch-off. The lever automatically goes to STOP position. agria Tool Carrier 5500 Grizzly...
This may damage the clutch release bearing. Ensure the lever is pulled (pawl is locked in place) when you park the machine with the engine stopped, otherwise clutch problems may result due to cor- rosion. agria Tool Carrier 5500 Grizzly...
The PTO shifting mechanism (B/8), however, is arranged at the tool carrier and is connected upon mounting of the attachment by the ball cup (A/9). PTO-shaft drive is connected PTO-shaft drive is disconnected agria Tool Carrier 5500 Grizzly...
Page 22
3. Devices and Operating Elements agria Tool Carrier 5500 Grizzly...
Page 23
PTO protection cap. Installing the cap: Hold protection cap against mounting flange. Fold both eye bolts into slots of protec- tion device. Evenly tighten both cap nuts. For de-installation proceed in reverse or- der. agria Tool Carrier 5500 Grizzly...
Hand Brake Pull hand lever (B/18) and lock with pawl (B/17) – both drive-wheels are blocked. To release hand brake, unlock pawl (B/17) and release lever (B/18) – B/18 B/17 brake is released. agria Tool Carrier 5500 Grizzly...
Fixing Points For towing away, recovering and tying down and to ensure a safe transport, use the fixing Points at the connection flange and engine food guard. Lashing in other places can lead to damage. agria Tool Carrier 5500 Grizzly...
2 operating hours with 100 Nm. Retighten bolts and nuts in each maintenance. Snow Chains When working with snow chains fitted on wheels, observe manufacturer’s in- structions, make sure there is sufficient clearance between chains and machine parts. agria Tool Carrier 5500 Grizzly...
Page 27
0190 111 20x8.00-10 grass tyre grass mainte- 3490 511 nance 21x11.00-8 Terra tyre mowing 3490 611 on soft + Interme- (boggy) diate flange ground 5519 031 For mowing on extremely steep slopes, we recommend using twin-wheels. agria Tool Carrier 5500 Grizzly...
Page 28
Use a grease gun (Bio lubrication grease). Adjustment of the differential Differential position The differential hubs are factory- set to differential effect, mount- ing of rigid position see fig. Rigid position agria Tool Carrier 5500 Grizzly...
By slightly applying pressure to the rear and front of the engine cowling, have the ball cups engage in the ball heads. To facilitate the installation, you may apply some bio-grease onto the rub- ber cups. agria Tool Carrier 5500 Grizzly...
Tighten cap nuts evenly. For PTO driven attach- ment, press link (6) onto shift lever (4) until it locks into place. Insert circlip and se- cure. For decoupling, proceed in reverse order. agria Tool Carrier 5500 Grizzly...
Check transmission oil level (see page 43) Note: For reasons of transport, the engine is not filled completey with engine oil! Before you operate the engine the first time, fill in engine oil (see page 39)! agria Tool Carrier 5500 Grizzly...
Then pull hard and fast to start the engine. After the start, carefully let rope glide back. Do not let snap. Once the engine has started, let it warm up for some time. Slowly push choke back into operating position, if necessary. agria Tool Carrier 5500 Grizzly...
Set speed control lever to idling po- sition. Pull hand clutch lever and hold. Move F/R drive to position reverse. Slowly release hand clutch lever while pressing the throttle. agria Tool Carrier 5500 Grizzly...
Cutter bar Rotary mower * 25 m * 25 m Flail mower * 20 m Safety Mulcher * 20 m Band rake Baler mountainpress Sweeper Snow dozer Stone burier Power harrow Surface conditioner Weed brush agria Tool Carrier 5500 Grizzly...
Starting the Engine on Slopes Keep the mowing drive and travel- ling drive in engaged mode; braking effect. Move the hand clutch lever and safety shifting lever to “Start” position. Start engine. agria Tool Carrier 5500 Grizzly...
Page 37
• Switch the traction drive to idle. The machine stops while the knives continue moving. This removes the debris from the mowing system. • Switch off the PTO shaft drive • Switch off the engine • Install the knife protection bar agria Tool Carrier 5500 Grizzly...
If the tank is to be emptied, this is to be accomplished outdoor. Let the engine cool down, before you store the machine in closed areas. Replace for safety reasons worn out or damaged parts. agria Tool Carrier 5500 Grizzly...
Clean filling- and drain plug and sur- rounding parts. Change the oil and dispose of prop- erly. Check sealing washer for good condition and exchange, if necessary! - For engine oil quality refer to “Specifi- cations”. agria Tool Carrier 5500 Grizzly...
Attach fastener (E). Install the cover and secure it with the fastener (A). Make sure that the fastener is firm. Replace immediately damaged filter elements. agria Tool Carrier 5500 Grizzly...
Clean fan system at least once per year, preferably before the season starts. Take off fan case and clean cooling fins on both, cylin- der and cylinder head, clean guiding plates and fan wheel, both serving for good air circulation. agria- Service agria Tool Carrier 5500 Grizzly...
Page 42
With speed control lever at idling, the engine should continue running smoothly. agria- Service Idling Speed Governor Keep governor spring, speed control lever and linkages free from dirt and plant trash at all times. agria Tool Carrier 5500 Grizzly...
Change oil, collect the old oil in a proper container and dispose of properly. Check and exchange o-rings, if necessary. Tighten the drain plug! For filling quantity and oil quality refer to "Specifications”. agria Tool Carrier 5500 Grizzly...
Page 44
Steering Handle Locking Bolt J, B Occasionally lubricate nipple on locking bolt of steering handle with Bio-lubrica- tion grease. Lubricate at least once a year and after cleaning with air-com- pressed water jets. agria Tool Carrier 5500 Grizzly...
Page 45
1 Stop buffer Re-tighten hexagonal nut (lock). 2 Lock nut for stop buffer 3 Adjustment nut for steering handle central mounting 4 Lock nut 5 Fastening nut for steering handle agria Tool Carrier 5500 Grizzly...
Page 46
A cally come to a stop. agria- Service Check electric conductors and con- nections for good condition, exchange, if necessary. agria- Service agria Tool Carrier 5500 Grizzly...
Screw the set pin (4) in or out (+ -) to a play of idle present in posi- tion 0. 1. Place cable end and set pin back into brack- 2.Fit retaining spring (2). agria Tool Carrier 5500 Grizzly...
To protect the bearings against penetrating dirt, sap and water, there shall be a grease collar at the bearing points. agria Tool Carrier 5500 Grizzly...
Drain the fuel completely from the system or fill the fuel tank and add e) Clutch stabilisator (agria No. 763 50) to the fuel Always park mower tank with hand clutch le- - Observe instructions.
6. Troubleshooting Observe safety instructions! Have all serious malfunctions on the machine or engine repaired by your agria workshop. They have the proper tools. Improper repairs can only add to the damage. Problem Possible cause Possible solution Page Petrol Engine:...
- Worn out clutch Exchange clutch disc Excessive - Loosened screws Tighten fastening screws vibration = For this purpose contact your agria workshop. 7. Decommissioning, Disposal Decommissioning Disposal If the two-wheel tractor is no longer After decommissioning the remaining...
K = Checks and maintenance to be executed by operator W = Maintenance to be executed by professional workshop F = Maintenance should be carried out by your agria workshop BM = Operator’s Manual Engine * = after 2 years...
Need help?
Do you have a question about the Grizzly 5500 Series and is the answer not in the manual?
Questions and answers