Genie Super-Straddle Operator's Manual
  1. Manuals
  2. Brands
  3. Genie Manuals
  4. Lifting Systems
  5. Super-Straddle
  6. Operator's manual
Genie Super-Straddle Operator's Manual

Genie Super-Straddle Operator's Manual

Hide thumbs Also See for Super-Straddle:
Table of Contents

Advertisement

Quick Links

See also: Service Manual

Advertisement

Table of Contents
loading

Related Manuals for Genie Super-Straddle

Summary of Contents for Genie Super-Straddle

  • Page 2: Table Of Contents

    Only trained and authorized personnel shall be permitted to operate this machine. This manual should be considered a permanent part of your machine and should remain with the machine at all times. If you have any questions, call Genie Industries. Contents Page Introduction ..............1 Symbols and Hazard Pictorials Definitions ....

  • Page 3: Introduction

    Second Edition • First Printing Introduction Owners, Users and Operators: Genie appreciates your choice of our machine for your application. Our number one priority is user safety, which is best achieved by our joint efforts. We feel that you make a major contribution to...
  • Page 4 The winch on the Super Straddle is only intended to hazards. Obey all safety lift the Genie AWP to the appropriate height. It is messages that follow this symbol not intended to lift people. to avoid possible injury or death.

  • Page 5: Symbols And Hazard Pictorials Definitions

    Insert outriggers. operator’s manual. pins. Crush hazard Keep away from Straddle socket Base frame Telescoping base moving parts. plug frame 0 m/ Maximum wind Pull gray tab to Outrigger load Indoor Use Only speed. release pin. Part No. 133409 Super-Straddle...

  • Page 6: General Safety

    Operator's Manual Second Edition • First Printing General Safety 133389 Safety signs and locations 133397 Decals with symbols 133389 133404 82487 133389 A 133397 82487 82487 133390 133404 133389 133396 133390 133391 133396 133391 133391 133396 133390 Super-Straddle Part No. 133409...

  • Page 7: Work Area Safety

    Tip-over Hazards for allowable side force and number of occupants in the Genie AWP operator’s manual. Do not use the Super-Straddle except with a Genie AWP. Some Genie AWP outriggers are rated for outdoor use. When using these outriggers with the...
  • Page 8 Be sure all decals are in place and legible. Be sure the Genie AWP operator’s, safety, and responsibilities manuals are complete, legible and in the storage container located on the AWP platform.

  • Page 9: Assembly And Disassembly

    3 Be sure that the telescoping tubes are inserted Assembly and Disassembly and pinned to the same length in the straddle platform. To move the Super-Straddle through a doorway or 4 Move the end frame to set it up after shipping, follow these instructions. marked Base Frame...
  • Page 10 3 Remove the telescoping tubes from the straddle platform and carry them to the assembly area. 4 Two people should carefully lift the straddle platform onto its side casters and roll it through the doorway. 5 Follow the assembly procedure. Super-Straddle Part No. 133409...

  • Page 11: Legend

    Operator's Manual Second Edition • First Printing Legend 1 Winch 11 Genie AWP outrigger 2 Frame retaining pin 12 Caster swivel lock 3 Electrical cord 13 Caster brake 4 Coil cord 14 Caster 5 Straddle socket plug 15 Ladder 6 Genie AWP...

  • Page 12: Inspections

    Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer's specifications and the requirements listed in the responsibilities manual. Super-Straddle Part No. 133409...
  • Page 13 Cracks in welds or structural components Dents or damage to machine Excessive rust, corrosion or oxidation Be sure that all structural and other critical components are present and all associated fasteners and pins are in place and properly tightened. Part No. 133409 Super-Straddle...
  • Page 14 3 Always perform function tests prior to use. Know and understand the function tests before going on to the next section. 4 Inspect the workplace. 5 Only use the machine as it was intended. Super-Straddle Part No. 133409...
  • Page 15 Inspections base frame decal Setup 7 Push the base frame carefully 1 Position the through all four Super-Straddle on a straddle sockets. firm, level surface. This may require 133405 A two people. Be sure 2 Apply the brakes to the straddle sockets...
  • Page 16 Super-Straddle to be inserted into the first set of holes. Do not raise the straddle platform past the first set of holes. 15 To insert a frame retaining pin, align the holes and lift up on the gray tab on the pin retaining interlock box.
  • Page 17 Second Edition • First Printing Inspections Test Retaining Pin Interlock Test Outrigger Interlock 19 At the platform controls of the Genie AWP, pull 25 Pull out the red Emergency Stop button at the out the red Emergency Stop button. platform controls.
  • Page 18 2 Always perform a pre-operation inspection. 3 Always perform function tests prior to use. 4 Inspect the workplace. Know and understand the workplace inspection before going on to the next section. 5 Only use the machine as it was intended. Super-Straddle Part No. 133409...
  • Page 19 • conductors hazardous locations • inadequate surface support to withstand all • load forces imposed by the machine wind and weather conditions • the presence of unauthorized personnel • other possible unsafe conditions • Part No. 133409 Super-Straddle...
  • Page 20 Use the appropriate inspection to verify that all decals are legible and in place. Part No. Description Quantity 62938 Cosmetic - Genie Super-Straddle 82487 Label - Read the Manual 133389 Label - Tip-over Hazard, Limit Switches 133390...
  • Page 21 Operator's Manual Second Edition • First Printing Inspections 133407 133389 Serial label 133397 82487 133405 82487 133390 133404 133412 133389 133420 133396 133406 133391 62938 133391 133412 133420 133396 133390 Part No. 133409 Super-Straddle...

  • Page 22: Operating Instructions

    5 Only use the machine as it was intended. inspection before using the machine. Use only Genie AWP with an X outrigger pattern. Super-Straddle Part No. 133409...
  • Page 23 8 Install frame retaining pins at Genie AWP outriggers. each corner of the Super-Straddle and release 4 Push the Super-Straddle into position next to the the tension on the winch object to be straddled. Two people are required cable. To insert frame...
  • Page 24 Lowering the Straddle Platform Super-Straddle casters are slightly off the ground. Use the bubble level on the Genie AWP 1 Fully lower the Genie AWP. to level the straddle platform. The bubble 2 Slightly raise the outriggers.

  • Page 25: Specifications

    Caster diameter 15.2 cm (four 4-position swivel locks with brake) Adjustable outriggers (required from Genie AWP) Load capacity of Super-Straddle is the same as the load capacity of the Genie AWP being used. Weight 263 kg Winch, rated load 680 kg...
  • Page 26 Genie North America Phone 425.881.1800 Toll Free USA and Canada 800.536.1800 Fax 425.883.3475 Genie Australia Pty Ltd. Phone +61 7 3375 1660 Fax +61 7 3375 1002 Genie China Genie Scandinavia Phone +86 21 53852570 Phone +46 31 575100 Fax +86 21 53852569...

Table of Contents