Subscribe to Our Youtube Channel
Related Manuals for Genie Super-Straddle
Summary of Contents for Genie Super-Straddle
- Page 1 Operator's Manual Serial Number Range Super-Straddle from SSP-7000 Australia with Maintenance Information Third Edition First Printing Part No. 1298031GT...
-
Page 2: Table Of Contents
Maintenance ............23 Specifications ............24 Copyright © 1992 Terex Corporation Third Edition: First Printing, September 2020 Genie is a registered trademark of Terex South Dakota, Inc. in the U.S.A. and many other countries. These machines comply with AS 1418.10 Super-Straddle Part No. -
Page 3: Introduction
The winch on the Super Straddle is only intended safety, which is best achieved by our joint efforts. to lift the Genie AWP to the appropriate height. It is This book is an operation and daily maintenance not intended to lift people. Before operating the manual for the user or operator of a Genie machine, it’s the operator’s responsibility to read... - Page 4 Operator's Manual Third Edition • First Printing Introduction Related machine movement: Base frame Telescoping base frame Straddle socket plug Swivel caster lock 1. Winch 2. Lifting bar Super-Straddle Part No. 1298031GT...
- Page 5 Bulletin Distribution and Contacting the Manufacturer Compliance At times it may be necessary to contact Genie. When you do, be ready to supply the model Safety of product users is of paramount number and serial number of your machine, along importance to Genie.
- Page 6 You read, understand and obey employer’s safety rules and worksite regulations. You read, understand and obey all applicable governmental regulations. You are properly trained to safely operate the machine. Super-Straddle Part No. 1298031GT...
-
Page 7: Symbol And Hazard Pictorials Definitions
Straddle socket plug Base frame Telescoping base moving parts frame Ladder storage Pull gray tab to Outrigger load Use on X-pattern Do not use on release pin outriggers. pinwheel outriggers. Maximum wind speed Indoor Use Only Part No. 1298031GT Super-Straddle... -
Page 8: General Safety
Operator's Manual Third Edition • First Printing General Safety Gener al Safety Super-Straddle Part No. 1298031GT... -
Page 9: Work Area Safety
Collision Hazards Be aware of overhead obstructions. The Super-Straddle adds 4 ft / 1.2 m to the working height of the Genie AWP being used. Crushing Hazards Keep hands away from end frame plates and moving parts when lowering the Super-Straddle. - Page 10 Be sure all decals are in place and legible. Be sure the Genie AWP operator’s, safety, and responsibilities manuals are complete, legible and in the storage container located on the AWP platform.
-
Page 11: Assembly And Disassembly
Assembly and Disassembly platform. Move the end frame To move the Super-Straddle through a doorway or marked Base Frame to set it up after shipping, follow these instructions. (refer to decal on ... - Page 12 Remove the telescoping tubes from the straddle platform and carry them to the assembly area. Two people should carefully lift the straddle platform onto its side casters and roll it through the doorway. Follow the assembly procedure. Super-Straddle Part No. 1298031GT...
-
Page 13: Legend
Third Edition • First Printing Operator's Manual Legend Legend Winch 11 Genie AWP outrigger Frame retaining pin 12 Caster swivel lock Electrical cord 13 Caster brake Coil cord 14 Caster Straddle socket plug 15 Ladder Genie AWP 16 Side casters... -
Page 14: Inspections
Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer’s specifications and the requirements listed in the responsibilities manual. Super-Straddle Part No. 1298031GT... - Page 15 Cracks in welds or structural components Dents or damage to machine Excessive rust, corrosion or oxidation Verify that all structural and other critical components are present and all associated fasteners and pins are in place and properly tightened. Part No. 1298031GT Super-Straddle...
- Page 16 Setup Position the Super-Straddle on a firm, level surface. 1 alignment spacer Apply the brakes to both 2 straddle socket swivel casters on the base 3 base frame frame.
- Page 17 Genie AWP, Super-Straddle to be inserted into the first set and then insert and of holes. Do not raise the straddle platform push it into the base past the first set of holes.
- Page 18 Third Edition • First Printing Inspections Test Retaining Pin Interlock Test Outrigger Interlock At the platform controls of the Genie AWP, pull 13 Pull out the red Emergency Stop button at the out the red Emergency Stop button. platform controls.
- Page 19 It should be performed by the operator prior to moving the machine to the workplace. It is the operator’s responsibility to read and remember the workplace hazards, then watch for and avoid them while moving, setting up, and operating the machine. Part No. 1298031GT Super-Straddle...
- Page 20 Label – Straddle Socket Plug 133412 Label – Retaining Pin Release 133420 Label – Outrigger Load 1272242 Label – Machine Registration/Owner Transfer 1294685 Instructions – Annual Inspection Shading indicates decal is hidden from view, i.e. under covers Super-Straddle Part No. 1298031GT...
- Page 21 Third Edition • First Printing Operator's Manual Inspections Part No. 1298031GT Super-Straddle...
-
Page 22: Operating Instructions
5 Only use the machine as it was inspection before using the machine. intended. Use only Genie AWP with an X outrigger pattern. Super-Straddle Part No. 1298031GT... - Page 23 See Setup section in the Function Tests section. straddled. Positioning, Raising and Leveling the Super-Straddle Be sure the Genie AWP is fully lowered. Raise the straddle platform just enough to lift the Genie AWP casters off the ground by turning each winch handle in a clockwise rotation.
- Page 24 11 Adjust the outrigger screw jacks so that the pads are in firm contact with the ground and Fully lower the Genie AWP. the Super-Straddle casters are slightly off the ground. Use the bubble level on the Genie Slightly raise the outriggers.
-
Page 25: Maintenance
Scheduled maintenance inspections shall be completed by qualified service technicians, according to the manufacturer’s specifications and the requirements specified in the responsibilities manual. For detailed maintenance and repair procedures, refer to the appropriate Service Manual for your machine. Part No. 1298031GT Super-Straddle... -
Page 26: Specifications
15.2 cm (four 4-position swivel locks with brake) Adjustable outriggers (required from Genie AWP) Load capacity of Super-Straddle is the same as the load capacity of the Genie AWP being used. Weight 580 lbs 263 kg Outrigger floor loading Information...
Need help?
Do you have a question about the Super-Straddle and is the answer not in the manual?
Questions and answers