Troubleshooting; Usb Black Box Port; Test Entrapment Sensors - Max 1500 PRO Installation Manual

This page and the next 3 pages can help troubleshoot problems that might occur after installation is complete.

usb black box port

Download a simple .txt file to troubleshoot gate operator errors and view event history.
BATTERY
BATTERY VOLTAGE
INPUT
E 1/2 F
ERROR
BATTERY
BATTERY
INPUT
BACKUP MODE
BATTERY
LEAVE OPEN
IN USE
OPEN 1 TIME
REPLACE
LEAVE
BATTERY
BATTERY
POWER / CLOSED
TEST
POWER
SOLAR IN
ERD SENSITIVITY
14 12 14 12
16 16
MIN MIN
ERD
1 9 1 9
MAX MOTOR MAX
MODULE
SENSE SENSE
OVER
3 7 3 7
PORT
LOAD
OPENING CLOSING
OBD PORT
RESET /
BLACK BOX
MANUAL MATRIX III
OFF
RELEASE
SWING / SLIDE
1
2
3
ALARM
4
5 PROGRAMMING MOTION CONTROL
ID PLUG 6
ERROR
1
2
3
ID
4
5
PLUG
6
7
OPEN STOP CLOSE
8 PROGRAM
9
10
OFF
QUICK
EXIT PWR OPEN
SOLAR MODE CLOSE
LEFT
EXIT LOOP
OFF ON
GND
OFF ON
GATE
CENTER LOOP
LOOP PWR
GATE SPEED
SAFETY LOOP OPERATOR
MIN MIN
FAULTS
MAX MAX
PRIMARY SECONDARY
24VDC OUTPUT
GND OPENING CLOSING
12VDC OUTPUT
GND
LINK
OK
PRIMARY/
SECONDARY
LINK

test entrapment sensors

Troubleshoot entrapment protection sensors:
1. Press and HOLD the STOP button & then the OPEN button together until beeping is heard, learn mode begins.
NOTE: DO NOT press the OPEN button before the STOP button or learn mode will NOT function.
2. LEDs should be ON if an entrapment sensor is detected in EACH input.
If LEDs are NOT on, sensors have a problem.
Possible problems:
• Photocells are out of alignment
• Photocells are wired wrong - N.C. or N.O. depending on which
photocells are used, see specific mfg instructions.
• Sensor is bad
3. Press STOP button again within 5 min. to end learn mode, beeping stops.
NOTE: If STOP button is not pressed within 5 min. learn mode automatically end after 5 min.

troubleshooting

MATRIX III
MOTOR
INPUTS
MOTOR
POSITION
INPUTS
CLOSE
TIMER
SLIDER
ERD
LIMIT
MOTOR
OVER
SWING
MIN MAX
LOAD
OFF
LIMIT
ON/OFF
BATTERY
JOG
GATE OPEN
COM
GATE CLOSED
GND
LEFT RIGHT
NO
MAG
LOCK COM
NC
MAGLOCK
OPEN
DELAY
RIGHT
OPEN ONLY NC
M A
PHOTO CLS NC
F l a
OFF 2.5 sec OPEN/CLS NC
1.5 sec 12VDC OUT
s h
GND
OPEN ONLY 10K
UL
ENTRAP CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
GND
1. Plug MAX USB flash drive into OBD port. OBD LED will flash while file is downloading.
Remove flash drive after LED stops flashing (up to 5 minutes to download).
2. Plug flash drive into any computer USB port OR smart phone using a USB phone adapter.
The most recent 8000 events can be viewed. No special software required.
S m
a r t
P h o
n e
n e
h o
C o m
B P
U S
e r
a p t
d
A d
i r e
q u
R e
O R
X
D r i
v e
O O O O O OPEN ONLY
PHOTO CLS P P P P
OPEN/CLS
12VDC OUT
OPEN ONLY
CLS ONLY
OPEN/CLS
12VDC OUT
UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7a
19
Event History Text Document Sample
Event type clarifica on:
INFO: informa onal message only
WARNING: unusual event but doesn't cause system malfunc on
ERROR: abnormal event, could cause system malfunc on
ENTRAP: entrapment detec on event
Event Report:
Fri 07/11/2014 10:59:41
Fri 07/11/2014 10:59:41
Fri 07/11/2014 10:59:37
Fri 07/11/2014 10:59:36
Fri 07/11/2014 10:58:54
Fri 07/11/2014 10:58:53
p u t
e r
Fri 07/11/2014 10:57:40
Fri 07/11/2014 10:57:38
Fri 07/11/2014 10:57:34
Fri 07/11/2014 10:57:21
Fri 07/11/2014 10:57:21
Fri 07/11/2014 10:56:46
Fri 07/11/2014 10:56:36
Fri 07/11/2014 10:56:36
Fri 07/11/2014 10:56:36
Fri 07/11/2014 10:56:33
Fri 07/11/2014 10:56:33
Fri 07/11/2014 10:56:33
Fri 07/11/2014 10:56:33
MOTION CONTROL
OPEN STOP
NC
Factory Learned Input
NC
Factory Learned Input
Unlearned Input
NC
Monitored Power
GND
10K
Unlearned Input
10K Unlearned Input
Unlearned Input
10K
GND
MOTION CONTROL
OPEN STOP CLOSE
INFO : Cycle Counter
ENTRAP : SEC_MC: First ERD Detected
INFO : Radio Input Deac vated
INFO : Radio Input Ac vated
INFO : PRI_MC: Fully Open Posi on Learned
INFO : SEC_MC: Fully Open Posi on Learned
INFO : PRI_CIO: Communica on Established
ENTRAP : PRI_MC: Photo Cell Deac vated
ENTRAP : PRI_MC: Photo Cell Ac vated
INFO : Radio Input Deac vated
INFO : Radio Input Ac vated
WARNING: PRI_MC: Tamper Reported
INFO : SEC_MC: Fully Open Posi on Unknown
INFO : PRI_MC: Fully Open Posi on Unknown
WARNING: PRI_MC: Tamper Reported
ENTRAP : PRI_MC: Photo Cell Deac vated
ENTRAP : PRI_MC: Photo Cell Ac vated
ENTRAP : PRI_MC: Photo Cell Deac vated
ENTRAP : PRI_MC: Photo Cell Ac vated
CLOSE
IMPORTANT: Sensing
devices MUST be
powered by Matrix III
or they will NOT be
MONITORED.