Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kontron KFM21_e
Summary of Contents for Kontron KFM21_e
-
Page 2: Table Of Contents
Operation of the OSD Menu................21 Installation Instructions ..................22 Instruction for the Mounting ................. 22 Assembly into a Control Panel................23 Monitor Connecting and Turning On ............... 24 Maintenance and Prevention ................25 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) - Page 3 Contents Main Specifications....................26 Mechanical Specifications ..................27 Electrical Specifications ..................27 Environmental Specifications ................28 EC Directives and Standards ................29 Technical Appendix - Interfaces ...............30 VGA Connector ....................30 DVI-D Connector (Single Link) ................31 S-Video Connector....................32 C-Video (Composite) Connector ................32 Technical Support....................33 Returning Defective Merchandise ................34 21.3"...
-
Page 4: Introduction
Kontron Embedded Computers is aware of such errors or inaccuracies or that Kontron Embedded Computers is unaware of these as a result of gross negligence and Kontron Embedded Computers has failed to eliminate these errors or inaccuracies for this reason. -
Page 5: Symbols Used In This Manual
Introduction Symbols used in this Manual Symbol Meaning This symbol indicates the danger of injury to the user or the risk of damage to the product if the corresponding warning notices are not observed. This symbol indicates that the product or parts thereof may be damaged if the corresponding warning notices are not observed. -
Page 6: Important Instructions
In the event of damage to the device caused by failure to observe the hints in this manual and on the device (especially the safety instructions), Kontron Embedded Computers shall not be required to honor the warranty even during the warranty period and shall be exempted from the statutory accident liability obligation. -
Page 7: Safety Instructions
This chapter also contains information on approval and interference suppression of your KFM21_e. The device has been built and tested by Kontron Embedded Computers in accordance with EN 60950/VDE 0805 and left the company in a perfectly safe condition. - Page 8 ❏ The device is designed to be used in vertical position. ❏ Repairs may only be carried out by a person authorized by Kontron Embedded Computers. ❏ Maintenance or repair on the open device may only be carried out by qualified personnel authorized by Kontron Embedded Computers which is aware of with the associated dangers.
-
Page 9: Fcc Statement
Safety Instructions FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment. -
Page 10: Scope Of Delivery
❏ VGA-cable connector ❏ 16x (M5) nut, DIN934, ST-ZN ❏ 16x 5.3 washer, DIN125 Type Labels and Product Identification The type label of your KFM21_e is attached at the back of the device. Type Label Product Identification KFM21_e 21.3" Industrial LCD Monitor KFM21_e with AC power supply unit 21.3"... -
Page 11: Product Description
Product Description Product Description The KFM21_e is a monitor which is designed for high-performance industrial applications. The solid type of enclosure offers the Monitor KFM21_e a mechanical stability. KFM21_e is proper therefore for industrial use. Excellent image representation, simple menu-driven handling and Plug & Play ability rounds off the qualities of this monitor. -
Page 12: Front Panel
Fig. 2: KFM21_e – with front side mounted operating elements and LED indicator) Fig. 2a: KFM21_e – with front side mounted “LED indicator” (if the OSD menu buttons and the power On/Off button are laterally mounted) 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) -
Page 13: Operating Elements And Led Indicator
4 LED indicator (if the OSD menu buttons and the power On/Off button are rear side mounted) The front panel of the monitor KFM21_e is suitable for the installation into control panels or other cabinets. The protection class IP 65 is ensured at the front side of the monitor. - Page 14 Prerequisite: The AC power cord must be attached to a power supply source. The LED indicator is at the front side for KFM21_e versions with OSD control keys mounted to the right side (rear-mounted); (refer to Fig. 2.a).
-
Page 15: Display
Product Description Display The built-in display is a 21.3" TFT UXGA display with up to 1600 x 1200 resolution and 250 cd/m of luminance (brightness). In front of the display there is installed a protection pane with antireflection properties. This protects the display surface from dirt and scratching also. -
Page 16: Left Side
You can connect one corresponding signal source to each interface at the same time. By means of the OSD-menu function “input select” you can select, which of the signal source shall be represented on the display. 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) -
Page 17: Power Plug
The VGA input is a 15-pin D-SUB connector (female), and allows you to connect an analog graphic card, by use of the supplied VGA-cable connector. Monitor KFM21_e supports at this interface data transfer with up to 1600 x 1200 resolution (UXGA). -
Page 18: Right Side
On/Off button” can be mounted optionally on the right side of the monitor (rear mounted). The “LED indicator” is for this version of the KFM21_e on the front panel (refer to Fig. 2a). (Option) Control Keys of the OSD and Power On/Off Button... -
Page 19: Rear Side
(see chapter “Installation Instructions”). On the rear side of the monitor are attached the type label and the approval marks. Fig. 6: KFM21_e - back-side 1 Threaded bolts for installation into control panels or other cabinets 2 Rubber seal... -
Page 20: Air Openings
(behind the front panel) are not obstructed. Power Supply The monitor KFM21_e is equipped with one “wide range” AC-power supply. The supply tension range can be read off the type label attached on the back of the unit. -
Page 21: Power Cord Connection
Product Description Power Cord Connection Use the power cord suitable for the power supply in your country. Do not remove or alter the grounding prong on the power cord. In situations where a two-slot receptacle is present, have it replaced with a properly grounded three-prong grounding type receptacle. -
Page 22: On Screen Display (Osd)
<Down> (to decrease). 7. Press the button <Menu> to choose the sub menu values. 8. To save a new setting, press the button <Menu> of the KFM21_e. 9. Press the button <Select> to leave (“Exit”) the sub-menu. -
Page 23: Installation Instructions
You find the description of the interfaces being available in the “Left Side” section. Important Instructions! The monitor KFM21_e has to be installed and operated only by trained and qualified personal. Since the device may weigh up to 15 kg, it is advisable to have a colleague assist in the installation. -
Page 24: Assembly Into A Control Panel
Installation Instructions Assembly into a Control Panel At the back side of the monitor KFM21_e there are 16 threaded bolts (each four bolts on every side) used for installation into a control panel or other cabinet. A cutout and 16 drill-holes (Ø 7.5 mm) corresponding the dimension in the hole pattern, have to be prepared first for a panel installation. -
Page 25: Monitor Connecting And Turning On
1. Connect the PC-system’s video signal-output interface to the video signal- input of the KFM21_e by use of the video signal cable (only the VGA cable connector is supplied). 2. Connect the power cord as described in the chapter “Power Cord Connection”. -
Page 26: Maintenance And Prevention
❏ Remove persistent dirt by use of a soft, slightly damp cloth (only use a mild detergent). Use no abrasives, abrasion sponges, steel wool, metal threads, or solvent like alcohol, acetone, washing gasoline to clean the displays protection pane. 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) -
Page 27: Main Specifications
Main Specifications Main Specifications TFT LCD Display Diagonally (Size) 21.3" (432 x 324 mm) Resolution Up to 1600 x 1200 dpi Pixel Pitch 0.270 mm x 0.270 mm Display colors 3x 8-Bit, 16.7 Mio. colors Backlight 6x CCFT Brightness 250 cd/m Viewing angle 170°... -
Page 28: Mechanical Specifications
Frontal: black powder coated Electrical Specifications System Integrated Input Version KFM21_e AC Power Supply 100 - 240 VAC (wide range) 50 - 60 Hz max. 0.6 A 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) -
Page 29: Environmental Specifications
Main Specifications Environmental Specifications Operating Temperature 0 … +50°C (32 122°F Storage / Transit –20 … +65 °C Temperature (–4 … 149 °F Relative Humidity 10 – 85 % (non condensing) Operating Altitude 10,000 ft (3,048 m) Storage / Transit Altitude 25,000 ft (7,620 m) Operating Shock 15 G, 11 ms duration, half sine... -
Page 30: Ec Directives And Standards
Standards Generic emission standard for industrial environments (Emission): EN 61000-6-4: 2001 EUROPE Generic standards – Immunity for industrial environments (Immunity): EN 61000-6-2: 2005 FCC 47 CFR Part 15, Class A 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) -
Page 31: Technical Appendix - Interfaces
Technical Appendix - Interfaces Technical Appendix - Interfaces The following tables show the plug assignments for the external connections of the KFM21_e. VGA Connector Signal Name 15-pin D-SUB-Socket (female) green blue 4 is NC 5–8 Fused VCC DDC Data HSYNC... -
Page 32: Dvi-D Connector (Single Link)
Differential TMDS Data 0– TMDS0+ Differential TMDS Data 0+ TMDS Shield 20–21 Reserved for future use TMDS Shield TMDSSCL– Differential TMDS Clock– TMDSSCL+ Differential TMDS Clock + C5– C6 Ground 21.3" Industrial LCD Monitor KFM21_e – User’s Manual (Version 2.00) -
Page 33: S-Video Connector
Technical Appendix - Interfaces S-Video Connector Signal Name Description 4-pin MiniDIN-Connector (female) Ground Ground Luminance Chrominance C-Video (Composite) Connector Signal Name Description Cinch-Connector (yellow) (female) Ground CVBS Composite video signal 21.3" Industrial LCD MonitorKFM21_e – User’s Manual (Version 2.00) -
Page 34: Technical Support
Be ready to explain the nature of your problem to the service technician. If you have questions about Kontron Embedded Computers or our products and services, you may reach us at the aforementioned numbers, or at: www.kontron.com... -
Page 35: Returning Defective Merchandise
(+49) 8165-77 412 e-mail: service@kontron.com 2. Make sure that you receive an RMA number from Kontron Embedded Computers-Service before returning any merchandise. Clearly write or mark this number on the outside of the package you are returning. 3. Describe the device failure behavior.