Phoenix Contact FL SWITCH 2005 User Manual
  1. Manuals
  2. Brands
  3. Phoenix Contact Manuals
  4. Switch
  5. FL SWITCH 2005
  6. User manual

Phoenix Contact FL SWITCH 2005 User Manual

Hide thumbs Also See for FL SWITCH 2005:
Table of Contents

Advertisement

Quick Links

FL SWITCH 2000
User manual
Order No. —

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FL SWITCH 2005 and is the answer not in the manual?

Questions and answers

Related Manuals for Phoenix Contact FL SWITCH 2005

Summary of Contents for Phoenix Contact FL SWITCH 2005

  • Page 1 FL SWITCH 2000 User manual Order No. —...

  • Page 2: Table Of Contents

    UM EN FL SWITCH 2000 Revision: Order No.: — This user manual is valid for: Designation Order No. Designation Order No. FL SWITCH 2005 2702323 FL SWITCH 2206-2FX SM 2702331 FL SWITCH 2008 2702324 FL SWITCH 2206-2FX ST 2702332 FL SWITCH 2105...
  • Page 3 How to contact us Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be found on the Internet at: phoenixcontact.com Make sure you always use the latest documentation.
  • Page 4 The receipt of technical documentation (in particular user documentation) does not constitute any further duty on the part of Phoenix Contact to furnish information on modifications to products and/or technical documentation. You are responsible to verify the suitability and intended use of the products in your specific application, in particular with regard to observing the applicable standards and regulations.
  • Page 5 4.2.1 Learning addresses ................25 4.2.2 Prioritization ..................26 Configuration and diagnostics in web-based management ............27 Requirements for the use of WBM............... 27 Functions/information in WBM................28 5.2.1 Information area of WBM ..............29 5 / 20 107065_en_01 PHOENIX CONTACT...
  • Page 6 Technical data for devices in the 2200 version ............ 78 11.4 Technical data for devices in the 2300 version ............ 81 11.5 Ordering data ...................... 85 Appendix for document lists......................89 List of figures ....................... 89 List of tables ......................93 Index........................95 6 / 20 PHOENIX CONTACT 107065_en_01...

  • Page 7: Factoryline Switch 2000 Range

    The Managed Switches in the 2000 version are Ethernet Switches which are suitable for in- dustrial use. They are available in the following versions: – With five 10/100 Mbps RJ45 ports (FL SWITCH 2005) – With eight 10/100 Mbps RJ45 ports (FL SWITCH 2008) The Managed Switches in the 2100 version are Gigabit Ethernet Switches which are suit- able for industrial use.

  • Page 8: Dimensions Of The Fl Switch 2000

    FL SWITCH 2000 1.1.1 Dimensions of the FL SWITCH 2000 Figure 1-1 Dimensions of the FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

  • Page 9: Elements Of The Devices

    FL SWITCH 2204-2TC-2SFX (2 Fast-Ethernet combo ports for 100 Mbps SFP mod- ules, ports 3 and 7) – FL SWITCH 2304-2GC-2SFP (2 Gigabit combo ports for 100 Mbps and 1000 Mbps SFP modules, ports 3 and 7) 107065_en_01 PHOENIX CONTACT...

  • Page 10: Status And Diagnostic Indicators

    LNK/ACT Green Link active Flashing Data transmission (at port top) Link not active Green/ Green: 100 Mbps orange Orange (for 2100/2300 version only): 1000 Mbps (at port bottom) 10 Mbps if Link LED is active PHOENIX CONTACT 107065_en_01...

  • Page 11: Mounting And Installation

    DIN rail. Push the module from the front towards the mounting surface (A2). Figure 2-1 Snapping the device onto the DIN rail • Once the module has been snapped on properly, check that it is fixed securely on the DIN rail. 107065_en_01 PHOENIX CONTACT...

  • Page 12: Installing The Devices

    US2 prevents this error message. It is possible to deactivate monitoring in web-based management or via SNMP. Operation with one power supply 1 2 3 4 5 Figure 2-3 Operating the device with one power supply (example) PHOENIX CONTACT 107065_en_01...

  • Page 13: Redundant Operation With Two Power Supplies (Example)

    US GND 1 2 3 4 5 Figure 2-5 Connecting a relay to the digital alarm output Please note that the relay must be suitable for the operating voltage. Use the RIF-0-RPT- 24DC/21 (Order No. 2903370), for example. 107065_en_01 PHOENIX CONTACT...

  • Page 14: Grounding

    SFP modules, the user can specify whether the switch has multimode or single- mode FO ports, for example. The SFP modules are available separately as accessories, see “Technical data and order- ing data” on page 75. PHOENIX CONTACT 107065_en_01...

  • Page 15: Elements Of The Sfp Modules

    Ensure correct mechanical alignment of the SFP modules. Figure 2-7 Inserting the SFP modules (example) Removing the SFP modules • Remove the FO connector before removing the SFP module. • Turn the release latch to the side and pull out the SFP module. 107065_en_01 PHOENIX CONTACT...

  • Page 16: Using The Sd Card

    FL SWITCH 2000 2.2.5 Using the SD card The switch is provided with a Phoenix Contact SD card, thereby enabling quick configura- tion. The slot for the SD card is located on the back of the device. Figure 2-8 Position of the SD card slot...

  • Page 17: Startup And Function

    LEDs of port X1 and X2 will flash. The active state is indicated alternately by the flashing of all four LEDs. • When Smart mode is started, the switch is initially in the “Exit without changes” state. 107065_en_01 PHOENIX CONTACT...

  • Page 18: Factoryline Switch 2000 Range3.2.2Selecting The Desired Setting

    Select the “Operating with a default IP address” Smart mode as described in “Using Smart mode” on page 17. The switch assigns an IP address to the PC via DHCP. The switch can now be accessed via IP address “192.168.0.254”. Set the desired IP address via web-based management. PHOENIX CONTACT 107065_en_01...

  • Page 19: Operating In Unmanaged Mode

    Internet. You can use any of these programs for address assignment. This section explains IP address assignment using the “FL NETWORK MANAGER Basic” (Order No. 2702889) and “IP Assignment Tool” software tools from Phoenix Contact. Notes on BootP During initial startup, the device sends BootP requests without interruption until it receives a valid IP address.

  • Page 20: Bootp Server

    BootP request in the BOOTP/DH- CP SERVER window and select “Add to BOOTP/DHCP reservations”. • Now enter the IP address to be assigned in the BOOTP/DHCP reservations window. The IP parameters are immediately transferred to the device. PHOENIX CONTACT 107065_en_01...

  • Page 21: Assigning The Ip Address Using Ipassign.exe

    Enter order number 2702323 in the search field, for example. The BootP IP addressing tool can be found among the various product-related downloads. • Double-click on the “IPAssign.exe” file. • In the window that opens, click on the “Run” button. 107065_en_01 PHOENIX CONTACT...
  • Page 22 The following information is displayed in the window which opens: – IP address of the PC – MAC address of the selected device – IP parameters of the selected device (IP address, subnet mask, and gateway address) – Any incorrect settings PHOENIX CONTACT 107065_en_01...
  • Page 23 The window that opens informs you that IP address assignment has been successfully com- pleted. It gives an overview of the IP parameters that have been transmitted to the device with the MAC address shown. To assign IP parameters for additional devices: • Click on the “Back” button. 107065_en_01 PHOENIX CONTACT...
  • Page 24 FL SWITCH 2000 To exit IP address assignment: • Click on the “Finish” button. If required, the IP parameters set here can be changed in web-based management (see Section “Network” on page 39). PHOENIX CONTACT 107065_en_01...

  • Page 25: Frame Switching

    “Clear” button. The aging time is set using the “dot1dTpAgingTime” MIB object (OID 1.3.6.1.2.1.17.4.2). The available setting range is 10 - 825 seconds. For static con- figuration, an aging time of 300 seconds is recommended. 107065_en_01 PHOENIX CONTACT...

  • Page 26: Prioritization

    Quality of Service affects the forwarding and handling of data streams and results in individ- ual data streams being given differential treatment (usually preferential). QoS can be used, e.g., to guarantee a transmission bandwidth for individual data streams. The switch uses QoS in connection with prioritization. PHOENIX CONTACT 107065_en_01...

  • Page 27: Configuration And Diagnostics In Web-Based Management

    In order to make changes, you must log into the device. To do so, click on the “Login” button. By default upon delivery, the user name is “admin” and the password is “private”. Figure 5-1 Login window 107065_en_01 PHOENIX CONTACT...

  • Page 28: Functions/Information In Wbm

    FL SWITCH 2000 Functions/information in WBM WBM is split into the following areas: – Information: general device information – Configuration: device configuration – Diagnostics: device-specific diagnostics Figure 5-2 Start page for web-based management (example) PHOENIX CONTACT 107065_en_01...

  • Page 29: Information Area Of Wbm

    – Description Files (SNMP) – IP Assignment Tool (see “Assigning the IP address using FL NETWORK MANAGER Basic” on page 19) 107065_en_01 PHOENIX CONTACT...
  • Page 30 Figure 5-4 “Device Status” web page 5.2.1.3 Technical Data Here you will find the technical data for your device, such as specifications for the power supply. Figure 5-5 “Technical Data” web page PHOENIX CONTACT 107065_en_01...

  • Page 31: Figure 5-6 "Local Diagnostics" Web Page

    The “Event Table” can be downloaded from the device in CSV format. Figure 5-7 “Alarm & Events” web page 5.2.1.6 Port Table You will find a list of the current states of the individual ports on this page. 107065_en_01 PHOENIX CONTACT...

  • Page 32: Figure 5-8 "Port Table" Web Page

    MAC Address Table You will find a list of the current devices in the network on this page. The list can be down- loaded from the device in CSV format. Figure 5-9 “MAC Address Table” web page PHOENIX CONTACT 107065_en_01...

  • Page 33: Configuration Area Of Wbm

    “System” web page The connection to the device is interrupted for the boot phase. Firmware Update Clicking on the “Update Firmware” link opens a pop-up in which the parameters for the firm- ware update must be entered. 107065_en_01 PHOENIX CONTACT...

  • Page 34: Figure 5-11 "Firmware Update Via Http" Pop-Up

    TFTP server IP address: Here, set the IP address of the computer on which the TFTP server is active. – Remote firmware filename: Here, set the name of the firmware file which is to be transferred to the device. PHOENIX CONTACT 107065_en_01...
  • Page 35 Update status: indicates the current transfer status. Start transfer: click on the “Start” button to start the transfer of the configuration. Configuration name: here you should enter the name under which you want to save the con- figuration on the PC. 107065_en_01 PHOENIX CONTACT...

  • Page 36: Figure 5-13 "Advanced Configuration" Pop-Up

    Transfer via HTTP: select “HTTP” as the transfer method. Clicking on “Browse” allows you to select the desired file on your PC. You can upload the desired file directly to the PC via your browser by selecting “HTTP Upload”. Figure 5-13 “Advanced Configuration” pop-up PHOENIX CONTACT 107065_en_01...

  • Page 37: Figure 5-14 "Advanced Configuration" Pop-Up

    Root CA: clicking on the “cacert.cer” link loads the Root CA certificate for the installation in the browser. Advanced Configuration: clicking on the “File transfer” link opens the “Advanced Configura- tion” pop-up (see “Pop-up: Advanced Configuration” on page 35). Figure 5-15 “Security Context” pop-up 107065_en_01 PHOENIX CONTACT...

  • Page 38: Figure 5-16 "Administrator Password" Configuration Area

    The basic settings can be made in Quick Setup. Figure 5-17 “Quick Setup” web page Automation Profile: select a profile which is optimized for the desired operating mode. IP Assignment: select the type of IP address assignment. PHOENIX CONTACT 107065_en_01...

  • Page 39: Figure 5-18 "Network" Web Page

    IP Address Assignment: select the type of IP address assignment. – STATIC: static IP address – BOOTP: assignment via the Bootstrap protocol – DHCP: assignment via a DHCP server If you have chosen “STATIC”, now make the following settings: IP Address: set the desired IP address. 107065_en_01 PHOENIX CONTACT...

  • Page 40: Figure 5-19 Acd Status Information On The "Device Status" Page

    Disable: transmission of CLI commands via the network is deactivated – Enable: transmission of CLI commands via the network is activated For additional information on using the CLI, refer to “Configuration and diagnostics via Command Line Interface (CLI)” on page 57. PHOENIX CONTACT 107065_en_01...

  • Page 41: Figure 5-21 "Port Configuration" Web Page

    Status: the port can be activated/deactivated here. Name: you can assign the port a name. Type: describes the physical properties of the port. Link: displays the current link status of the port. Negotiation Mode: indicates the current auto negotiation status. 107065_en_01 PHOENIX CONTACT...
  • Page 42 Link Monitoring: here you can set whether the link behavior is to be monitored at the se- lected port. Default Priority: set the priority for incoming data packets at this port here. Flow Control: flow control for the selected port can be enabled and disabled here. PHOENIX CONTACT 107065_en_01...

  • Page 43: Figure 5-22 "Port Configuration Table" Web Page

    Clicking on the “Configure Port Settings for a VLAN” button takes you to the “VLAN Port Configuration” page (see “VLAN Configuration” on page 71). 5.2.2.6 VLAN Configuration For additional information on “VLAN”, refer to “Virtual Local Area Network (VLAN)” on page 71. Figure 5-23 “VLAN Configuration” web page 107065_en_01 PHOENIX CONTACT...

  • Page 44: Figure 5-24 "Multicast Filtering" Web Page

    FL SWITCH 2000 5.2.2.7 Multicast Filtering Figure 5-24 “Multicast Filtering” web page For additional information on “Multicast”, refer to “Multicast filtering” on page 69. 5.2.2.8 Network Redundancy Spanning-Tree Configuration Figure 5-25 “Spanning-Tree Configuration” configuration area RSTP Mode: PHOENIX CONTACT 107065_en_01...
  • Page 45 The manager function is only available for the 2200/2300 versions provided that the SD card is inserted and has a MRP master license (MRM) (see “Ordering data” on page 85). Ring Port 1: select the first MRP ring port here Ring Port 2: select the second MRP ring port here 107065_en_01 PHOENIX CONTACT...

  • Page 46: Figure 5-26 "Rstp Port Configuration" Web Page

    Designated Port ID: indicates the port via which the BPDUs are sent from the designated bridge. The value is based on the port priority (2 digits) and the port number. Designated Cost: displays the path costs of this segment to the root switch. Protocol Version: displays the protocol version. PHOENIX CONTACT 107065_en_01...

  • Page 47: Figure 5-27 "Rstp Port Configuration Table" Web Page

    (10 Mbps = 2000000; 100 Mbps = 200000). 5.2.2.9 Security Figure 5-28 “Security” web page Secure UIs: clicking on the “Security Context” link opens the pop-up of the same name (see page 37). 107065_en_01 PHOENIX CONTACT...

  • Page 48: Figure 5-29 "Dhcp Service" Web Page

    Network Mask: set the subnet mask that is assigned to the DHCP clients here. – Router IP: set the router/default gateway IP address that is assigned to the DHCP cli- ents here. – DNS IP: set the DNS IP address that is assigned to the DHCP clients here. PHOENIX CONTACT 107065_en_01...

  • Page 49: Figure 5-30 "Dhcp Port Local Service" Pop-Up

    System Uptime: displays the time that has elapsed since the IP address was assigned to the client. – Local Port: indicates the port to which the client is connected. – State: indicates the status of the client. – Lease count: displays the number of assigned IP addresses. 107065_en_01 PHOENIX CONTACT...

  • Page 50: Figure 5-31 "Local Events" Web Page

    Power Supply lost: in the event that US1 or US2 is lost – Monitored link down: under “Advanced”, select the ports to which link down behavior should be reported. – MRP Ring Failure: indicates an error message in the event of an MRP ring error. PHOENIX CONTACT 107065_en_01...

  • Page 51: Figure 5-32 "Quality Of Service" Web Page

    Port Configuration Table: clicking on the “Configure Flow control for multiple ports at once” link opens the “Port Configuration Table” web page where flow control can be configured for all ports. Figure 5-32 “Quality of Service” web page 107065_en_01 PHOENIX CONTACT...

  • Page 52: Diagnostics Area Of Wbm

    Operating Mode: indicates the current MRP device status. MRP Manager Function: indicates whether an MRP manager license (MRM) is available. The following fields are only available after selecting “Manager” as the operating mode. Ring Status: indicates the current status of the MRP ring. PHOENIX CONTACT 107065_en_01...

  • Page 53: Figure 5-34 "Mrp Diagnostic" Web Page

    “MRP Diagnostic” web page 5.2.3.4 Current VLANs For additional information, refer to “Current VLANs” on page 74. 5.2.3.5 Current Multicast Groups For additional information, refer to “Multicast filtering” on page 69. 5.2.3.6 Port Mirroring Figure 5-35 “Port Mirroring” web page 107065_en_01 PHOENIX CONTACT...

  • Page 54: Figure 5-36 "Trap Manager" Web Page

    Test Trap Connection: the connection to the trap server is tested by clicking on the “Send Trap” button. The table lists the SNMP traps which can be sent by the device. Here you can select the actions for which SNMP traps should be sent. PHOENIX CONTACT 107065_en_01...

  • Page 55: Figure 5-37 "Port Counter" Web Page

    5.2.3.9 Port Utilization Figure 5-38 “Port Utilization” web page Here you will find an overview of the port utilization for this device as a percentage. For a detailed overview, click on the graph of an individual port. 107065_en_01 PHOENIX CONTACT...

  • Page 56: Figure 5-39 "Sfp Diagnostics" Web Page

    Serial No: the serial number of the SFP module used is displayed in this column. RX Power (dBm): the incoming power level is displayed in this column. TX Power (dBm): the outgoing power level is displayed in this column. PHOENIX CONTACT 107065_en_01...

  • Page 57: Configuration And Diagnostics Via Command Line Interface (Cli)

    “Assigning IP parameters via BootP” on page 19 and “Network” on page 39. Figure 6-1 Configuration of a Telnet connection in PuTTY Figure 6-2 Command terminal in PuTTY 107065_en_01 PHOENIX CONTACT...

  • Page 58: Basic Principles For Using Cli Commands

    Denotes the mandatory selection of a value from a given list of values | Vertical bar choice1 | choice2 Separates mutually exclusive selection options [{}] Braces within square [{choice 1 | choice 2}] Denotes a selection within an optional parameter brackets PHOENIX CONTACT 107065_en_01...

  • Page 59: Command Syntax

    Table 6-2 Structure of CLI commands Command Description Display available commands Typing a question mark (?) after each entry displays all the available command names or parameters from this point on. 107065_en_01 PHOENIX CONTACT...

  • Page 60: Auto-Completion Of Commands

    The Autocomplete command is an additional way of writing a command, provided enough letters have already been entered to clearly identify the command name. As soon as enough letters have been entered, press space or TAB to automatically complete the words. PHOENIX CONTACT 107065_en_01...

  • Page 61: Using The Cli Network Scripting Ui

    The following examples illustrate the correct syntax for entering commands via the CLI Net- work Scripting UI: Example: changing the device name http://192.168.10.42/php/command.php?usr=admin&pwd=private&cmd=device-identity name Switch2000 Example: displaying the network parameters and changing the user password http://192.168.10.42/php/command.php?usr=admin&pwd=private&cmd=show network | users passwd private2 107065_en_01 PHOENIX CONTACT...
  • Page 62 FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

  • Page 63: Simple Network Management Protocol (Snmp)

    SNMP objects, which are then assigned to a private manufacturer area in the large SNMP object tree. Manufacturers are then responsible for their own private (enterprise) areas, i.e., they must ensure that only one object (object name and parameters) 107065_en_01 PHOENIX CONTACT...
  • Page 64 The descriptions of the individual SNMP objects are located in the respective MIBs and can be downloaded from the Phoenix Contact e-shop. Note that the MIB is located in a firm- ware’s respective software package (zip file).

  • Page 65: Link Layer Discovery Protocol (Lldp)

    The switch manages a maximum of 50 items of neighborhood information, all other infor- mation is ignored. If several neighbors are displayed on one switch port, then at least one other switch/hub, which does not support or has not activated LLDP, is installed between this switch and the neighbor indicated. 107065_en_01 PHOENIX CONTACT...

  • Page 66: Link Layer Discovery Protocol" Web Page

    For devices in the 2000/2100 version, LLDP can be activated or deactivated globally for all ports. Devices in the 2200/2300 version also offer a port-based configuration option for sending and receiving LLDP telegrams. The LLDP can be configured on the “Service” page in WBM (see “Service” on page 40). PHOENIX CONTACT 107065_en_01...

  • Page 67: Lldp Topology" Web Page

    MAC address of the connected neighboring device – IP address Indicates the management IP address of the neighbor. – Remote Port Indicates the port number of the neighboring switch that is used to connect the neighbor to the local switch. 107065_en_01 PHOENIX CONTACT...
  • Page 68 FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

  • Page 69: Multicast Filtering

    Extension BUQ (Block Unknown at Querier): select here whether unknown multicast pack- ets should be blocked at the querier. 107065_en_01 PHOENIX CONTACT...

  • Page 70: Current Multicast Groups" Web Page

    Static Query Ports: select which ports are static query ports. Clicking on the “Current multicast groups” link opens the “Current Multicast Groups” web page as a pop-up. The device can manage up to 50 dynamic multicast groups. Figure 9-2 “Current Multicast Groups” web page PHOENIX CONTACT 107065_en_01...

  • Page 71: Virtual Local Area Network (Vlan)

    Tagged: in “Tagged” mode, the switch forwards the data packets depending on the VLAN assignment. Clicking on the “Static VLAN Configuration” button takes you to the “Static VLAN Configu- ration” page. Up to 8 (2000/2100 version) or up to 32 (2200/2300 version) static VLANs can be set up here. 107065_en_01 PHOENIX CONTACT...
  • Page 72 -: not a member of the VLAN Use the “Delete” button to delete the VLAN selected in the list. VLAN 1 cannot be deleted. Clicking on the “VLAN port configuration” button takes you to the “VLAN Port configuration” page. PHOENIX CONTACT 107065_en_01...

  • Page 73: Vlan Port Configuration" Web Page

    Clicking on the “VLAN Port Table” button takes you to the VLAN port table. Pop-up: VLAN Port Configuration Table Figure 10-4 “VLAN Port Configuration Table” web page Clicking on the “Current VLANs” link opens the “Current VLANs” web page as a pop-up. 107065_en_01 PHOENIX CONTACT...
  • Page 74 FL SWITCH 2000 Current VLANs This page lists the current VLANs and displays the ports for each VLAN, which are either “Tagged” or “Untagged”. Figure 10-5 “Current VLANs” web page PHOENIX CONTACT 107065_en_01...

  • Page 75: 11 Technical Data And Ordering Data

    At 100 Mbps: 148800 pps Supported MIBs MIB II and private SNMP objects from Phoenix Contact Housing dimensions (width x height x depth) in mm 45 x 130 x 115 (depth from top edge of DIN rail) Permissible operating temperature 0°C to 60°C...

  • Page 76: Technical Data For Devices In The 2100 Version

    Test intensity 1, criterion A Additional certifications RoHS 11.2 Technical data for devices in the 2100 version General data Function Ethernet/Fast Ethernet/Gigabit Switch; conforms to standard IEEE 802.3/802.3u/802.3ab Switch principle Store and forward Address table 8192 MAC addresses PHOENIX CONTACT 107065_en_01...
  • Page 77 At 1000 Mbps: 1488100 pps Supported MIBs MIB II and private SNMP objects from Phoenix Contact Housing dimensions (width x height x depth) in mm 45 x 130 x 115 (depth from top edge of DIN rail) Permissible operating temperature 0°C to 60°C...

  • Page 78: Technical Data For Devices In The 2200 Version

    64-byte packet size, half duplex At 100 Mbps: 148800 pps Supported MIBs MIB II and private SNMP objects from Phoenix Contact Housing dimensions (width x height x depth) in mm 45 x 130 x 115 (depth from top edge of DIN rail) PHOENIX CONTACT...

  • Page 79: Fl Switch 2206-2Fx St

    1.3 A (FL SWITCH 2208) 1.4 A (FL SWITCH 2207-FX) 1.4 A (FL SWITCH 2207-FX SM) 1.5 A (FL SWITCH 2206-2FX) 1.5 A (FL SWITCH 2206-2FX SM) 1.5 A (FL SWITCH 2206-2FX ST) 1.5 A (FL SWITCH 2206-2FX SM ST) 107065_en_01 PHOENIX CONTACT...

  • Page 80: Fl Switch 2206-2Fx Sm St

    850/1310 nm (depending on the device/SFP module used) Properties of the combo ports Number Up to 2 Transmission speed 100 Mbps Wavelength Depends on the SFP module used Maximum transmission length Depends on the SFP module used PHOENIX CONTACT 107065_en_01...

  • Page 81: Technical Data For Devices In The 2300 Version

    II 3 G Ex nA IIC T4 Gc IECEx ULD 16.0018X  11.4 Technical data for devices in the 2300 version General data Function Ethernet/Fast Ethernet/Gigabit Switch; conforms to standard IEEE 802.3/802.3u/802.3ab Switch principle Store and forward Address table 8192 MAC addresses 107065_en_01 PHOENIX CONTACT...
  • Page 82 At 1000 Mbps: 1488100 pps Supported MIBs MIB II and private SNMP objects from Phoenix Contact Housing dimensions (width x height x depth) in mm 45 x 130 x 115 (depth from top edge of DIN rail) Permissible operating temperature -40°C to 70°C...
  • Page 83 Test intensity 3, criterion B Air discharge: Test intensity 3, criterion A Indirect discharge: Test intensity 3, criterion A Noise immunity according to EN 61000-4-3 (IEC 1000-4-3) Requirements according to DIN EN 61000-6-2 (electromagnetic fields) Test intensity 3, criterion A 107065_en_01 PHOENIX CONTACT...
  • Page 84 EN 60079-0:2012+A11:2013 EN 60079-15:2010 Field of application: II 3 G Ex nA IIC T4 Gc IECEx ULD 16.0018X  Differences between this version and previous versions of the user manual Rev. 00: initial version Rev. 01: devices added PHOENIX CONTACT 107065_en_01...

  • Page 85: Ordering Data

    Products Description Order designation Order No. Pcs./Pkt. Managed Switch with five 10/100 Mbps RJ45 ports FL SWITCH 2005 2702323 Managed Switch with eight 10/100 Mbps RJ45 ports FL SWITCH 2008 2702324 Managed Switch with five 10/100/1000 Mbps RJ45 ports FL SWITCH 2105...
  • Page 86 Patch cable, CAT6, pre-assembled, 1.0 m long FL CAT6 PATCH 1,0 2891385 Patch cable, CAT5, pre-assembled, 1.0 m long FL CAT5 PATCH 1,0 2832276 HOTLINE: If there are any problems that cannot be solved using this documentation, please call our hotline: PHOENIX CONTACT 107065_en_01...
  • Page 87 Technical data and ordering data + 49 5281 9-462888 107065_en_01 PHOENIX CONTACT...
  • Page 88 FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

  • Page 89: A Appendix For Document Lists

    Login window ..................27 Figure 5-2: Start page for web-based management (example) ......28 Figure 5-3: “Help & Documentation” web page ............. 29 Figure 5-4: “Device Status” web page ..............30 Figure 5-5: “Technical Data” web page ..............30 107065_en_01 PHOENIX CONTACT...
  • Page 90 Figure 5-37: “Port Counter” web page ..............55 Figure 5-38: “Port Utilization” web page ..............55 Figure 5-39: “SFP Diagnostics” web page .............. 56 Section 6 Figure 6-1: Configuration of a Telnet connection in PuTTY ........57 PHOENIX CONTACT 107065_en_01...
  • Page 91 “Static VLAN Configuration” web page ..........72 Figure 10-3: “VLAN Port configuration” web page ........... 73 Figure 10-4: “VLAN Port Configuration Table” web page ........73 Figure 10-5: “Current VLANs” web page ..............74 Section 11 Appendix A 107065_en_01 PHOENIX CONTACT...
  • Page 92 FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

  • Page 93: List Of Tables

    Section 6 Table 6-1: Structure of CLI commands ..............58 Table 6-2: Structure of CLI commands ..............59 Section 7 Section 8 Table 8-1: Event table for LLDP................66 Section 9 Section 10 Section 11 Appendix A 107065_en_01 PHOENIX CONTACT...
  • Page 94 FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

  • Page 95: C 3 Index

    Housing dimensions ......... 75, 77, 78, 82 Humidity............ 75, 77, 79, 82 Default IP address............18 Default Priority............. 42 IEEE 802.1D ............... 26 Degree of protection ......... 75, 77, 79, 82 ifMIB................63 Delivery state .............. 17 IGMP Query Version ........... 69 107065_en_01 PHOENIX CONTACT...
  • Page 96 Path Cost ..............46 snmpMIB ..............63 pBridgeMIB ..............63 Snoop Aging Time ............69 Port Counter..............55 Source and destination addresses......25 Port ID ................. 46 Static Query Ports ............70 Port Mirroring ............43, 54 PHOENIX CONTACT 107065_en_01...
  • Page 97 Switch principle ......... 75, 76, 78, 81 Tagged................ 71 Topology Change............52 Traffic classes ............. 26 Transparent..............71 Trap ................63 Trap Manager ............. 54 Tree structure of the MIB..........64 User name ..............17 Utilization ..............55 VLAN/priority tag............26 107065_en_01 PHOENIX CONTACT...
  • Page 98 FL SWITCH 2000 PHOENIX CONTACT 107065_en_01...

This manual is also suitable for:

Fl switch 2008Fl switch 2105Fl switch 2108Fl switch 2205Fl switch 2207-fxFl switch 2208 ... Show all

Table of Contents