XB2 was designed around a no compromise platform; the attention to detail creates a low maintenance, have any difficulties, problems, or questions, please do not hesitate to contact the XRAY support team at extra long life electric buggy. The ultra-low center of gravity (CG) and optimized weight balance makes info@teamxray.com.
Page 3
Please support your local hobby shop. We at XRAY Model Racing Cars support all local hobby dealers. Therefore we ask you, if at all possible, to purchase XRAY products at your hobby dealer and give them your support like we do. If you have difficulty finding XRAY products, please check out www.teamxray.com to get advice, or contact us via email at info@teamxray.com, or contact the XRAY distributor in your country.
Reamer (HUDY #107600) or (HUDY #107601) Socket 7.0mm Allen 2.0mm EQUIPMENT INCLUDED INCLUDED XRAY offers wide range of optional HUDY Premium Silicone Oils Graphite Grease Follow Set-Up Book To ensure that you always have access SAMPLE OF tuning parts which are listed in a...
Page 5
XB2 TECH TIPS DRIVE SHAFT PIN SERVICING To enjoy the longest possible lifespan of the drive shafts and diff outdrives, it is extremely important to properly service the drive shaft pins. Inspect the pins after every 3 hours of runtime. If the pins show any wear, replace them with new pins. Press out the worn pins.
Page 6
1. DIFFERENTIAL 325061 941014 325012 930126 365080 325053 930120 930508 #324901 GEAR DIFFERENTIAL FOR 2.5mm PIN - SET 325022 #325326 941014 REAR DRIVE SHAFT 73mm WITH 2.5mm PIN 365080 HUDY SPRING STEEL™ 325072 305092 30 5092 BALL DIFFERENTIAL SPRING 32 5072 ALU BALL DIFFERENTIAL NUT 32 5002 BALL ADJUSTABLE DIFFERENTIAL FOR 2.5mm PIN SET - SPRING STEEL™...
Page 7
1. DIFFERENTIAL 930508 BB 5x8x2.5 NOTE ORIENTATION Square shape orientation on TOP side. DIFF GREASE (HUDY #106211) BEARING OIL (HUDY #106230) Round shape orientation on BOTTOM side. 930120 2.4mm carbide balls (12x) B 2.4 DIFF GREASE (HUDY #106211) Use HUDY Ball-Bearing Grease #106220 - STANDARD #106221 - BLUE 941014...
Page 8
BALL DIFF BREAK-IN & SET-UP INFO BEFORE RACING, follow these steps to properly break in the differential. FULLY TIGHTEN Loosen the adjustment screw 1/2 turn (180° CCW). ½ (180° CCW) LOOSEN THE ADJUSTMENT SCREW HOLD THE SPUR GEAR HOLD THE LEFT ROTATE THE WHEEL IN THE REAR WHEEL DIRECTION OF TRAVEL...
2. REAR TRANSMISSION GEAR BOX GEAR BOX FRONT MOTOR POSITION MIDDLE MOTOR POSITION (For HIGH TRACTION track) (For LOW TRACTION track) Top shaft in LOWER position Top shaft in HIGHER position MIDDLE Motor Position FRONT Motor Position 324011 303141 324225 902310 324012 323016...
Page 10
2. REAR TRANSMISSION GEAR BOX FRONT MOTOR POSITION (For HIGH TRACTION track) 981310 P 3x10 3x10mm 980320 P 3x20 3x20mm 3x10mm #323015-G COMPOSITE FRONT-MID MOTOR GEAR BOX (3 GEARS) GRAPHITE - NARROW - SET BEARING OIL (HUDY #106230) 940613 BB 6x13x5 930308 BB 3x8x4 GRAPHITE GREASE...
Page 11
2. REAR TRANSMISSION BEARING OIL (HUDY #106230) Bearing with BLUE rubber covers 902316 902320 SH M3x16 SH M3x20 940512 BB 5x12x4 902310 SH M3x10 "CLICK" GRAPHITE GREASE (HUDY #106210) 903308 SFH M3x8...
3. REAR SUSPENSION GEAR BOX GEAR BOX FRONT MOTOR POSITION MIDDLE MOTOR POSITION (For LOW TRACTION track) (For HIGH TRACTION track) 323081-M 902310 902316 323550 902320 902312 323080 902325 For Front motor Gear box assembly For Middle motor Gear box assembly follow instructions on page 19 .
Outer position = 1° or 0.75mm from center. The XRAY rear alu lower suspension holders provide great range of adjustment for the rear suspension. Using different combinations of eccentric bushings, fine adjustment of rear anti-squat, rear toe-in, rear roll center, and rear track-width can be obtained. For more information about the influence of rear anti-squat, rear toe-in, rear roll center and rear track width on car handling, please refer to HUDY Set-up Book (#209100).
Page 17
3. REAR SUSPENSION GEAR BOX FRONT MOTOR POSITION (For HIGH TRACTION track) ALTERNATIVE 1 SHOCKS MOUNTED IN FRONT OF REAR SHOCK TOWER (INITIAL SETTING) 902310 SH M3x10 902316 SH M3x16 ALTERNATIVE 2 SHOCKS MOUNTED BEHIND REAR SHOCK TOWER DO NOT USE FOR BASIC SET-UP 902320 SH M3x20 For the rear shock position cut...
Page 18
3. REAR SUSPENSION GEAR BOX MIDDLE MOTOR POSITION (For LOW TRACTION track) NOTE ORIENTATION 902312 SH M3x12 REAR SHOCK TOWERS #323081-M MEDIUM INCLUDED #323081-H HARD OPTION MEDIUM - For very-low & low traction HARD - For medium & high traction VIEW 903306 DETAIL...
Page 20
- 0 slots OPTION ➒ #365354 -0.75mm - Lightw. OPTION 10x15x4mm ➏ OPTIONAL HEX HUB EFFECTS Different offset hex hubs are used to increase or decrease the track-width. XRAY BALL-BEARING 5x12x4mm LESS OFFSET MORE OFFSET #940512 5x12x4 OIL OPTION 941014 ➑...
Page 21
3. REAR DRIVETRAIN Ensure that the rear upright moves freely. If it does not move freely, use sandpaper to thin both 306219 LONGER WHEELBASE wheelbase adjustment shims. SHIM 3x6x1 Adjustment Shim IN FRONT OF HUB moves hub rearward. 3x6x2mm 306219 SHIM 3x6x2 3x6x1mm 902254...
4. FRONT ASSEMBLY STEERING PLATE #322570 OPTION #322571 COMPOSITE INCLUDED 930306 322571 STEERING ARMS 902306 303141 #322510 OPTION 940510 #322511 COMPOSITE INCLUDED 303141 321290 FRONT LOWER CHASSIS BRACE #321262-M MEDIUM OPTION #321262-H HARD INCLUDED 940510 322511 SIDE CHASSIS GUARDS 321260-M #321260-M MEDIUM INCLUDED 902312...
Page 23
4. FRONT ASSEMBLY NOTE SIDE CHASSIS GUARDS ORIENTATION #321260-M MEDIUM INCLUDED 903308 #321260-H HARD OPTION SFH M3x8 MEDIUM - For low & medium traction HARD - For high traction 903308 SFH M3x8 For low traction tracks is recomended do not use these screws (L=R) 3x8mm 902308 3x8mm...
Page 24
4. FRONT ASSEMBLY STEERING PLATE NOTE ORIENTATION 303141 #322570 OPTION SHIM 3x5x1 #322571 COMPOSITE INCLUDED COMPOSITE - Easy to drive, more forgiving, less steering 3x5x1mm - More aggressive, more steering, more precise steering BEARING OIL (HUDY #106230) STEERING ARMS NOTE ORIENTATION #322510 ALU OPTION 902312...
5. FRONT SUSPENSION 902308 362290 322290 980210 960030 902205 325240 362291 359050 362651 322250-H 359050 365353 STEERING BLOCK 302665 322610 #322250-M MEDIUM OPTION #322250-H HARD INCLUDED #322250-G GRAPHITE OPTION 302665 302665 SUSPENSION ARM 362651 #322110-M MEDIUM OPTION #322110-H HARD INCLUDED 322610 362651 362280...
Page 26
5. FRONT SUSPENSION NOTE ORIENTATION SUSPENSION ARM #322110-M MEDIUM OPTION 902254 LEFT ARM = RIGHT ARM SH M2.5x4 #322110-H HARD INCLUDED NOTE #322110-G GRAPHITE OPTION ORIENTATION MEDIUM - For very-low & low traction 961025 HARD - For medium & high traction S 2.5 GRAPHITE - For high &...
Page 30
6. SHOCK ABSORBERS ➋ ➌ There are two different thickness shims, use them as shown. Use the same procedure when 965023 ➊ C 2.3 building both front and rear shocks. THICK Shim 970080 2 holes (1.6mm) O 8x1 O-ring THIN Shim INITIAL PISTON 972031 O 3x2.1...
Page 31
6. SHOCK ABSORBERS DEFAULT SHOCK REBOUND SETTING 0% REBOUND Follow the steps below to set the shock rebound to the default setting of 0%. FRONT (SHORT) TIGHTEN FULLY 350cSt 902205 REAR (LONG) SH M2x5 300cSt 3~5x UP & DOWN ➊ ➋...
LEXAN REAR WING - LOW TRACTION 36 1320 BODY MOUNT, BATTERY MOUNT - V2 & WING SHIM (2) 32 9706 XRAY XB2 BODY - LOW TRACTION 36 2650 BALL END 4.9mm WITH THREAD 6mm (2) 32 9910 2WD FRONT WHEEL AERODISK WITH 12mm HEX - WHITE (2)
Page 33
7. FINAL ASSEMBLY LONG Install the pivot balls with Professional 901312 SB M3x12 Multi Tool (HUDY #183011) 6mm THREAD 6mm THREAD SHORT 1.5mm HUDY ALU SERVO HORNS NOTE Use appropriate servo arm: #293497 ORIENTATION 902308 K - (23T) KO Propo / JR / Sanwa / Multiplex #293498 SH M3x8 H - (24T) Hitec...
Page 34
7. FINAL ASSEMBLY NOTE ORIENTATION 902312 SH M3x12 #322080 GRAPHITE SHOCK TOWER FRONT 4.0mm FRONT NOTE ORIENTATION DETAIL NOTE ORIENTATION INITIAL SETTING SHORT SHOCK 902322 DETAIL SH M3x22 INITIAL SETTING 960030 NUT M3 ALU NUTS M3 #296530-B ALU BLUE OPTION #296530-K ALU BLACK OPTION #296530-O ALU ORANGE OPTION...
7. FINAL ASSEMBLY BATTERY STRAP 901304 #326112-M MEDIUM INCLUDED SB M3x4 #326112-H HARD OPTION 3x10mm 3x12mm 902310 SH M3x10 902312 SH M3x12 Battery pack (NOT INCLUDED) BATTERY WEIGHT #326180 50g OPTION #326181 35g OPTION Foam spacer (INITIAL SETTING) REAR BATTERY POSITION: more traction on rear supspension, less steering FRONT BATTERY POSITION: The foam battery spacer can be installed...
Page 40
7. FINAL ASSEMBLY LESS TRACTION MORE TRACTION REAR WING SHIM #293561 SILVER OPTION BODY REAMER (HUDY #107600) 903308 #293561-O ORANGE OPTION SFH M3x8 LEXAN REAR WING #323510 1.0mm V1 OPTION #323511 1.5mm V1 OPTION #323513 1.0mm V2 INCLUDED #323514 1.5mm V2 OPTION GEAR BOX GEAR BOX FRONT MOTOR POSITION...
Page 41
When you have finished cutting, peel off the external protective films. ➑ GEAR BOX GEAR BOX FRONT MOTOR POSITION MIDDLE MOTOR POSITION XRAY LEXAN BODY #329700 0.75mm OPTION #329701 0.5mm OPTION #329706 0.75mm ALPHA 2 INCLUDED #329707 0.75mm BETA 2 OPTION #329708 0.50mm BETA 2...
Page 42
7. FINAL ASSEMBLY 960240 N M4 REAR wheel (WIDE) (NOT INCLUDED) FRONT wheel (NARROW) (NOT INCLUDED) #321190 #323512 FRONT LEXAN® WING XB2 GRAPHITE FRONT WING HOLDER ALTERNATIVE 1 UPPER POSITION ALTERNATIVE 2 LOWER POSITION 902306 #902304 962030 M3x4 323512 NOTE ORIENTATION #902314 M3x14 Countersunk holes...
MAINTENANCE SHOCK MAINTENANCE The most important maintenance task for keeping consistent shock performance is refilling and bleeding them correctly. If built correctly, it will not be necessary to re-build them often. Replacing warped/hard o-rings, scarred piston rods, or shaved/split/loose composite upper and lower ball joints are also important. •...
Page 44
RC AMERICA, 2030 Century Center Blvd #15, Irving, TX 75062, USA PHONE: 214-744-2400, FAX: 214-744-2401, xray@rcamerica.com...
Need help?
Do you have a question about the XB2D 2019 and is the answer not in the manual?
Questions and answers