Phone: (800) 519-7221 * (214) 744-2400 many other goodies. We pride ourselves on taking excellent care of our customers. Fax: +421-32-7401109 Fax: (214) 744-2401 You can join thousands of XRAY fans and enthusiasts in our online community at: Email: info@teamxray.com Email: xray@rcamerica.com www.teamxray.com Failure to follow these instructions will be considered as abuse and/or neglect.
Page 3
Therefore we ask you, if at all possible, to purchase • For the best performance, it is very important that great care is taken to ensure XRAY products at your hobby dealer and give them your support like we do. If the free movement of all parts.
Page 4
Allen 1.5mm Socket 7.0mm Allen 2.0mm EQUIPMENT INCLUDED INCLUDED XRAY offers wide range of optional Follow Set-Up Book To ensure that you always have access HUDY Premium Silicone Oils Graphite Grease SAMPLE OF tuning parts which are listed in a...
Page 5
XB2 TECH TIPS DRIVE SHAFT PIN SERVICING To enjoy the longest possible lifespan of the drive shafts and diff outdrives, it is extremely important to properly service the drive shaft pins. Inspect the pins after every 3 hours of runtime. If the pins show any wear, replace them with new pins.
Page 7
DIFFERENTIAL DIFF GREASE (HUDY #106211) 930508 BB 5x8x2.5 CUTAWAY VIEW NOTE ORIENTATION Square shape orientation BEARING OIL on TOP side. (HUDY #106230) Round shape orientation on BOTTOM side. DIFF GREASE (HUDY #106211) 930120 B 2.4 DIFF GREASE (HUDY #106211) THREAD LOCK IMPORTANT: When you build the differential, do not tighten it fully initially;...
Page 8
BALL DIFF BREAK-IN & SET-UP INFO The differential is factory pre-assembled including all greases, but is NOT ready to race immediately. BEFORE RACING, follow these steps to properly break in the differential. INITIAL BALL DIFFERENTIAL BREAK-IN Loosen the adjustment screw ¼ turn (90° CCW). ¼...
Page 9
BALL DIFF BREAK-IN & SET-UP INFO SLIPPER CLUTCH & BALL DIFFERENTIAL ADJUSTMENT It is critical that the slipper clutch and ball diff tension be set so FIRST SLIPPER CLUTCH ALWAYS SLIPS that the slipper clutch always slips FIRST before the ball diff. The ball diff should NEVER slip as this will damage diff balls and diff washers.
3. REAR SUSPENSION 323081-M 902312 323320 362315 323120-M 323310 357330 323110-M 362315 321100 REAR SHOCK TOWERS #323081-M MEDIUM (INCLUDED) #323081-H HARD (OPTION) REAR SUSPENSION ARMS 903306 #323110-M RIGHT - MEDIUM (INCLUDED) #323120-M LEFT - MEDIUM (INCLUDED) 903322 #323110-H RIGHT - HARD (OPTION) #323120-H LEFT - HARD (OPTION)
Page 14
Outer position = 1° or 0.75mm from center. The XRAY rear alu lower suspension holders provide great range of adjustment for the rear suspension. Using different combinations of eccentric bushings, fine adjustment of rear anti-squat, rear toe-in, rear roll center, and rear track-width can be obtained. For more information about the influence of rear anti-squat, rear toe-in, rear roll center and rear track width on car handling, please refer to HUDY Set-up Book (#209100).
Page 15
REAR SUSPENSION 902312 SH M3x12 NOTE ORIENTATION REAR SHOCK TOWERS #323081-M MEDIUM (INCLUDED) #323081-H HARD (OPTION) MEDIUM - For very-low & low traction HARD - For medium & high traction 903306 SFH M3x6 NOTE ORIENTATION 903322 SFH M3x22 3x6mm 3x22mm...
Page 16
3. REAR DRIVETRAIN 902312 363520 DRIVE SHAFT COLLAR #365470 COMPOSITE (INCLUDED) #365471-K ALU - BLACK (OPTION) 302665 #365471-O ALU - ORANGE (OPTION) 323042-M REAR UPRIGHTS 362610 #323350-M MEDIUM (INCLUDED) 362651 #323350-H HARD (OPTION) 302665 902310 #323351 (OPTION) 980210 362280 362652 365320 WHEEL HUBS 12MM 362280...
Page 17
REAR DRIVETRAIN 940510 BB 5x10x4 940512 BB 5x12x4 BEARING OIL REAR UPRIGHTS (HUDY #106230) 5x10x4mm #323350-M MEDIUM (INCLUDED) #323350-H HARD (OPTION) #323351 (OPTION) MEDIUM - For very-low & low traction 5x12x4mm HARD - For medium & high traction - For very-high traction OPTIONAL OFF-SET HEX HUB EFFECTS 980210...
Page 18
REAR DRIVETRAIN Ensure that the rear upright moves freely. If it does not move freely, use sandpaper to thin both wheelbase 306219 LONGER WHEELBASE (INITIAL SETTING) SHIM 3x6x2 adjustment shims. Adjustment Shim IN FRONT OF HUB moves hub rearward. 902254 SH M2.5x4 3x6x2mm SHORTER WHEELBASE...
4. FRONT ASSEMBLY 930306 322571 902306 303141 940510 303141 321290 940510 322511 321260-M 902312 322550 930306 321260-M 903308 321265 321262-M 322311 903308 902308 903310 FRONT LOWER ARM MOUNT 903308 #322310 ALU 26º (OPTION) 903308 #322311 COMPOSITE 26º (INCLUDED) #322312 BRASS 26º (OPTION) #322313 ALU 23°/29°...
Page 20
FRONT ASSEMBLY NOTE ORIENTATION 903308 SFH M3x8 903308 SFH M3x8 903308 SFH M3x8 903310 SFH M3x10 903318 SFH M3x18 FRONT LOWER CHASSIS BRACE #321262-M MEDIUM (INCLUDED) 3x10mm #321262-H HARD (OPTION) MEDIUM - For very-low, low & medium traction. Generates more traction. HARD - For high- &...
Page 21
FRONT ASSEMBLY 303141 NOTE ORIENTATION SHIM 3x5x1 3x5x1mm BEARING OIL (HUDY #106230) 902312 STEERING PLATE SH M3x12 NOTE ORIENTATION #322571 COMPOSITE (INCLUDED) #322570 (OPTION) COMPOSITE - easy to drive, more forgiving, less steering 3x5x1mm - more aggressive, more steering, more precise steering 930306 BB 3x6x2.5 STEERING ARMS...
Page 23
FRONT SUSPENSION NOTE ORIENTATION 902254 LEFT ARM = RIGHT ARM SH M2.5x4 NOTE SUSPENSION ARM ORIENTATION #322110-M MEDIUM (INCLUDED) #322110-H HARD (OPTION) #322110-G GRAPHITE (OPTION) MEDIUM - For very-low & low traction HARD - For medium & high traction TIGHTEN GRAPHITE - For high &...
Page 24
FRONT SUSPENSION OPTIONAL OFF-SET HEX HUB EFFECTS ➊ Different off-set hex hubs are used to 902205 increase or decrease the track-width. SH M2x5 LESS OFF-SET Rear - more traction Front - more steering 981210 MORE OFF-SET P 2x10 Rear - less traction ➌...
Page 25
FRONT SUSPENSION ROLL CENTER LINKS NOTE ORIENTATION 39.5mm 6mm THREAD 8mm THREAD THREAD THREAD ROLL CENTER LINKS NOTE ORIENTATION 362280 CON. SHIM 3x6x2 CONICAL SHIM 3x6x2mm 8mm THREAD DETAIL INITIAL SETTING NOTE ORIENTATION DETAIL 6mm THREAD INITIAL SETTING ROLL CENTER 8mm THREAD STEERING LINKS NOTE ORIENTATION...
Page 27
SHOCK ABSORBERS Downstop shim. THICKER shim used, INITIAL SETTING GREATER downstop is achieved. EXTREMELY IMPORTANT 306219 IMPORTANT SHIM 3x6x1 Always use same shim thickness on right 2mm 3mm and left side to achieve same downstop. ➋ ➋ 3x6x1mm ➊ 3x6x1mm ➊...
Page 28
SHOCK ABSORBERS FRONT SHOCKS (SHORT) IMPORTANT REAR SHOCKS (LONG) Both FRONT SHOCKS must be the same overall length. Both REAR SHOCKS must be the same overall length. SHORT FRONT SHOCKS LONG REAR SHOCKS Short Springs Long Springs ALTERNATE SHOCK REBOUND SETTING (50% AND 100%) The default shock rebound setting is 0% (as described on page 25).
BODY MOUNT, BATTERY MOUNT - V2 & WING SHIM (2) 32 9700 XRAY XB2 BODY 32 9701 XRAY XB2 BODY - LIGHT (OPTION) 36 2650 BALL END 4.9MM WITH THREAD 6MM (2) 36 5718~23 ALU PINION GEAR HARD COATED 18~23T/48 (OPTION)
Page 30
FINAL ASSEMBLY LONG 901312 SB M3x12 6mm THREAD 6mm THREAD SHORT 1.5mm NOTE Use appropriate servo arm: ORIENTATION 902308 K - (23T) KO Propo / JR / Sanwa / Multiplex SH M3x8 H - (24T) Hitec F - (25T) Futaba NOTE ORIENTATION LONG...
Page 31
FINAL ASSEMBLY NOTE ORIENTATION 902312 SH M3x12 FRONT SHOCK TOWERS #322080 GRAPHITE (OPTION) #322081-M MEDIUM (INCLUDED) #322081-H HARD (OPTION) MEDIUM - For very-low & low traction HARD - For medium & high traction GRAPHITE - For high & very-high traction NOTE ORIENTATION INITIAL SETTING...
Page 32
FINAL ASSEMBLY XRAY PINIONS DETAIL #365718 18T / 48P #365719 19T / 48P 902306 SH M3x6 #365720 20T / 48P #365721 21T / 48P #365722 22T / 48P #365723 23T / 48P PINION (NOT INCLUDED) Adjust the motor so the pinion meshes with the spur gear properly.
Page 34
FINAL ASSEMBLY 3x10mm 901304 3x12mm SB M3x4 902310 SH M3x10 BATTERY STRAP 902312 SH M3x12 #326112-M MEDIUM (INCLUDED) #326112-H HARD (OPTION) BATTERY (NOT INCLUDED) FOAM SPACER (INITIAL SETTING) REAR BATTERY POSITION: more traction on rear supspension, less steering The foam battery spacer can FRONT BATTERY POSITION: be installed either in front less traction on rear suspension, more corner speed...
Page 35
FINAL ASSEMBLY VELCRO™ TAPE WITH DOUBLE-SIDED TAPE (Strong side tape) (Soft side tape) OPTIONAL WING SHIM #293561 ALU REAR WING SHIM SILVER (OPTION) #293561-O ALU REAR WING SHIM ORANGE (OPTION) 903308 SFH M3x8 LEXAN™ REAR WING #323510 1.0mm THICK (INCLUDED) #323511 1.5mm THICK (OPTION)
Page 36
LEFT MOTOR POSITION ASSEMBLY MOTOR POSITION ASSEMBLY Follow these steps to change your motor position to the LEFT side. Use the solidly-colored optional parts shown in the exploded view. 324121 364131 365881 364131 364140 902340 364131 324120 940512 324190 323011 325000 980320 364180...
Page 37
LEFT MOTOR POSITION ASSEMBLY PAGE 9 / STEP 1 981310 P 3x10 INITIAL SETTING DETAIL 3x10mm 980320 3x20mm P 3x20 3x10mm PAGE 10 / STEP 1 930308 BB 3x8x4 NOTE ORIENTATION GRAPHITE GREASE (HUDY #106210) 303141 3x5x1mm SHIM 3x5x1 GRAPHITE GREASE 3x5x1mm (HUDY #106210) NOTE ORIENTATION...
Need help?
Do you have a question about the XB2 and is the answer not in the manual?
Questions and answers