Download Print this page
Danfoss KPU 19 Installation Manual
Danfoss KPU 19 Installation Manual

Danfoss KPU 19 Installation Manual

Advertisement

Quick Links

Installation guide
Thermostat
Type KPU
Application
KPU 19 thermostats are used
for temperature regulation
in refrigeration, freezing, air
conditioning, ventilating and heating
systems.
KPU 19 thermostats are fitted with
Single-Pole Double-Throw (SPDT)
or Single-Pole Single-Throw (SPST)
contact system.
The standard KPU 19 enclosure is rated
NEMA ~ 1.
NEMA ~ 1 is obtained when the
thermostat is mounted on a flat
surface with all unused holes covered.
Product specification
Type
Regulating
Differential
range
[°F]
∆T [°F]
KPU 19
-30
80
3.6
KPU 19
-30
80
3.6
KPU 19
-30
80
3.6
Dimensions [in.]
Thermostat bulb types
remote bulb
remote bulb
remote bulb
remote bulb
Bulb size
Capillary tube
length
[in.]
[in.]
12.6
/
x 4
/
120
3
1
8
2
12.6
/
x 4
/
3
1
8
2
Air coil / Room
12.6
-
sensor
Scale Plate
Mounting Hole
DIFF.
Di . Adjusting
Knob
Terminal Screw
Capillary Tube
Grounding Screw
Conduit Rubber
DKRCC.PI.CA0.F1.22 / 520H10107
air coil/room sensor
air coil/room sensor
air coil/room sensor
air coil/room sensor
Max. bulb
Ambient
temperature
temperature
[°F]
-31
140
-31
80
140
-31
140
Cover
1.7
2.12
Important
The KPU 19 thermostat is designed
only for use as a temperature
regulating operating control. It is the
responsibility of the installer to verify
that other necessary safety controls
are installed and functioning properly
as intended by the original equipment
manufacturer or system design.
Contact
Reset
type
type
[°F]
158
SPDT
Auto.
SPST
158
(close on
Auto.
temp. rise)
140
SPDT
Auto.
0.63
0.59
0.14
0.27
Code no.
060L2150
060L2151
060L2152
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the KPU 19 and is the answer not in the manual?

Questions and answers

Summary of Contents for Danfoss KPU 19

  • Page 1 The standard KPU 19 enclosure is rated manufacturer or system design. NEMA ~ 1. NEMA ~ 1 is obtained when the thermostat is mounted on a flat surface with all unused holes covered.
  • Page 2 Do not make additional holes. the thermostat will not be subject Locking mounting holes must be to damage. Mount the KPU 19 on a fastened at position A as shown in bracket or on a completely flat surface. diagram to the right. Fastening at Mounting on an uneven surface may position “B”...
  • Page 3 Wiring options For Cooling Unit: For Heating Unit: cut-out on temperature decrease cut-out on temperature increase ~LINE ~LINE LOAD LOAD Contact function Example for application and wiring Manual Changeover Switch Cooling Heating Cooling Heating Unit Unit Unit Unit Power Source Power Source Power Source SPDT...
  • Page 4 (hereinafter referred to as “Purposes”), but are not designed and manufactured for the purpose of using the Products for any instrument or system related to human life or health purposes. Therefore, the use of the Products in elds related to items (1) through (3) below is not intended whatsoever. Danfoss shall be held harmless and be indemni ed from any and all damages incurred by use of the Products under item (3).

This manual is also suitable for:

Kpu series