Specifi Cations - Behringer ULTRADRIVE PRO DCX2496 User Manual

30 ULTRADRIVE PRO DCX2496/ULTRADRIVE DCX2496LE User Manual
With two DCX2496 units you can even realize today's most popular surround format:
5.1. In addition to the speaker cabinets and power amps (or active speakers as in
the simplifi ed illustration shown here), all you need is a surround decoder to play
back pre-produced 5.1 material such as DVDs, or a mixing console with six outputs
(e.g. stereo out plus four subgroups). In the latter case, you can create highly
sophisticated surround mixes even without a special surround sound decoder.
The preset "5.1 FRONT" has been optimized for the L-C-R front speakers
with 2 speaker ways each (see also chapter 5.3). The three signals required
"Front-Left, Front-Center, Front-Right" are routed via the three inputs (A, B, C)
to the fi rst DCX2496.
On the second DCX2496, the preset "5.1 REAR" should be used as a starting
point. It supplies the two rear surround speakers (also 2-way systems) plus the
monophonic sub-bass channel ("LFE" = "Low Frequency Enhanced") with the
input signals "Rear-Left, Rear-Right and Sub-bass", using connectors In A, B, C.
The sixth output of the second ULTRADRIVE PRO is not used in this application,
but is left available for additional eff ects or as a mono delay line.
This scenario does not apply to the DCX2496LE.

7. Specifi cations

Analog Inputs (A, B, C)
Type electronically balanced
Connector XLR
Max. input level +22 dBu
Input impedance approx. 35 kΩ @ 1 kHz
Crosstalk -72 dB @ 0 dBu
Digital Input (A) - DCX2496
Connector XLR
Format S/PDIF or AES/EBU
Input level 0.3 to 10 Vpp
Input impedance approx. 110 Ω
Sampling frequency 32 to 96 kHz
Special feature Sample Rate Converter
Microphone Input (C) - DCX2496
Type electronically balanced
Connector XLR
Max. input level -23 dBu
Input impedance approx. 670 Ω @ 1 kHz
Phantom supply +15 V
Analog Outputs (1, 2, 3, 4, 5, 6)
Type electronically balanced
Connector XLR
Max. output level +22 dBu
Output impedance approx. 100 Ω @ 1 kHz
Crosstalk -100 dB @ 10 dBu
System Data
Sampling frequency 96 kHz
Signal delay < 1 ms Analog input to analog output
Frequency response 10 Hz to 45 kHz (-3 dB) typ.
Dynamic range 112 dB
THD+N Ratio 0,007% @ 0 dBu
0,004% @ 10 dBu
31 ULTRADRIVE PRO DCX2496/ULTRADRIVE DCX2496LE User Manual
Converters
A/D Converter CS5381
Resolution 24-Bit Delta-Sigma
Oversampling 64x
Dynamic range 120 dB typ.
D/A Converter AK4393
Resolution 24-Bit Delta-Sigma
Oversampling 64x
Dynamic range 120 dB typ.
Serial Interface (DCX2496)
RS-232
Type 9-pin sub-D connector
Transmission type 115200 bauds, 8 data bits,
1 stop bit, no parity
RS-485 (2x)
Type RJ-45 connector
Transmission type 38400 bauds, 8 data bits,
1 stop bit, no parity
Power Supply
Mains Voltage
USA/Canada 120 V~, 60 Hz
Europe/U.K./Australia 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
General export model 100 - 240 V~, 50 - 60 Hz
Power consumption approx. 12 W
Fuse 100 to 240 V~: T 1 A H
Mains connector Standard IEC receptacle
Dimensions/Weight
Dimensions (H x D x W) 45 x 483 x 208 mm
(1.75 x 19 x 8.1")
Weight approx. 2 kg (4.4 lbs)
Shipping Weight approx. 3.2 kg (7 lbs)