Summary of Contents for Shimano SRD
- Page 1 ROWING SRD Footstretcher Assembling Manual Shimano,Inc © 2009 Shimano, Inc. ALL RIGHTS RESERVED...
-
Page 2: Table Of Contents
(10) Fixing the Frame Unit ………………………..…………………….P12 (11) Adjusting the Height of the Binding Units ……….……………….P13 (12) Adjusting the position of the SRD Footstretcher System ………P14 (12) -1/2/3 How you can measure the position …..………………….P15 (14) Adjusting the Heel Plates …..…………………………..………. P17 (15) Adjusting the Step-in Position …..…………………..…………. -
Page 3: Check Contents In The Box
U it （left） （right） Binding Unit Binding Unit （left） （right） KF-R600 Lower Fitting Attachment Pipe • These are all in the package. • Binding units are fixed on the Frame Units in the package. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 4: Genuine Boat Parts Applied To Srd
ROWING (2) Genuine Boat Parts Applied to SRD Upper Pipe Mounting(left) Mounting(left) Upper Pipe Mounting(right) Upper Pipe(25mm φ) • These genuine parts should be applied from your boat to mount SRD Footstretcher. Lower Mounting © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 5: Tools
Ａ：Hexagon Wrenches(3mm will be used mainly) Ｂ：Angle Meter Ｃ：Tape Measure Ｄ：String Ｅ：Tool(s) each boat manufacturer recommend to fix the Footstretcher system. In this photo 10mm Wrench is shown. Ｆ L Ｆ：Long Aluminum Rectangle Pipe l Pi Ｇ：Level © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 6: Installing Attachment Pipe
・Let the Lower Pipe go through the Lower Pipe. the Lower Pipe metal fitting cramps, then tighten temporarily. (You do not have to il (Y ・Install the Lower Pipe. tighten these firmly before the procedure (6) ) © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 7: Installing The Upper Pipe
(↑) (↑) (↑)and slide down the Binding (↑)and slide down the Binding and install the upper pipe. Unit. With this operation it will be easier to manipulate the Upper Pipe. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 8: Temporary Assemble
ROWING (6) Temporary Assemble • Put your SRD Footstretcher on the boat by using tools the boat manufacturer recommends. • CAUTION: Do not too much loosen the bolts on the Binding Units shown on procedure (5)-1, otherwise the unit might... -
Page 9: Adjusting The Footstretcher Angle
Frame Unit. 50° *All the bolts on Footstretcher system has to be fastened when you try to check the precise angle, otherwise the measurements will be inaccurate measurements will be inaccurate. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 10: Checking The Space
(8) Checking the Space • Allow 1CM space between the edge of the SRD Footstretcher system and the inside of the hull. It is easier to check whether the space is enough or not by moving a small stick such as a pencil around the Footstretcher. -
Page 11: Adjusting The Stance
(8)again to make sure there is the enough space. • If you are setting SRD Footstretcher on the single scull, we recommend to have the stance as wide as the space against the hull allows the space against the hull allows. -
Page 12: Fixing The Frame Unit
Fasten all the bolts to hold the upper and lower pipes firmly. • With this operation you will completely set the angle of the SRD Footstretcher System. So check the Footstrecher angle again as shown at procedure (7) ． © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 13: Adjusting The Height Of The Binding Units
The lowest point of the top surface ,usually edge of the holes (X), should be measured to check the height of the seat. k th h i ht f th © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 14: Adjusting The Position Of The Srd Footstretcher System
ROWING (12) Adjusting the position of the SRD Footstretcher System • Loosen the 3 mounting bolts and adjust the position of the Footstretcher System by sliding forward and backward on the gear rails gear rails. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 15: 1/2/3 How You Can Measure The Position
Footstretcher and the SRD System. *The Boat should be laid on the slings in completely horizontal way horizontal way. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... - Page 16 1-2 fists. • If this space is too much open, move the Footstretcher system toward the stern. If too narrow toward the bow too narrow, toward the bow. © 2009 Shimano, Inc. ALL RIGHTS RESERVED...
-
Page 17: Adjusting The Heel Plates
Loosen the bolt and slide the Heel Plates up and down on the Binding Unit. • This part is set to support the heel of the shoes Readj st to determine the best shoes. Readjust to determine the best position. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 18: Adjusting The Step-In Position
ROWING (15) Adjusting the Step-in Position • You can adjust the range of swinging motion by the adjustment bolt which locates on the reverse side of the swing arm. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 19: Adjusting The Binding Tension
ROWING (16) Adjusting the Binding Tension • You can adjust the Binding Tension by the You can adjust the Binding Tension by the adjustment bolt which is shown with the orange arrow. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 20: Installing The Cleats
• Set the cleat nut on the holes Set the cleat nut on the holes Then tighten the bolts. ti ht th b lt provided on the SRD shoes. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... -
Page 21: Adjusting The Position Of The Cleats
(18) Adjusting the position of the Cleats • You can adjust the position of the Cleats by sliding along of the Cleats by sliding along the holes of the Cleats, and the shoes. © 2009 Shimano, Inc. ALL RIGHTS RESERVED... - Page 22 ROWING (18) Now you are ready • Now your SRD Footstretcher system is ready to go. • When you get on the boat, hook the front of the cleat on the binding first ( ) , then press down on the heel plate(↓).
- Page 23 The Systems photographed in this document are all prototypes, so the look and the spec is subject to be changed without any notice. • Use this document just as a reference when the SRD System is newly introduced. For your safety, read carefully the technical service instruction attached with the products. © 2009 Shimano, Inc. ALL RIGHTS RESERVED...