CyberPower RMCARD205 Quick Start Manual
Remote management card
Hide thumbs
Also See for RMCARD205:
- User manual (83 pages) ,
- Quick start manual (8 pages) ,
- Quick start manuals (2 pages)
Table of Contents
Advertisement
Remote Management Card
Remote Management Card
RMCARD205
RMCARD305
SAVE THESE INSTRUCTIONS
Please read this guide and follow the instructions for installation and use.
Copyright © 2017 Cyber Power Systems, Inc. All rights reserved.
QUICK START GUIDE
R M
C A
C y
R D
3 0 5
b e r
U n
i v e
r s a
P o
l
w e
L i n
r
k
T x /
R x
R M
C A
R D
2 0 5
U n
i v e
r s a
l
L i n
k
T x /
C y
R x
b e r
P o
w e
r
K01-0000449-02
Advertisement
Table of Contents
Related Manuals for CyberPower RMCARD205
Summary of Contents for CyberPower RMCARD205
- Page 1 QUICK START GUIDE Remote Management Card Remote Management Card RMCARD205 RMCARD305 3 0 5 b e r i v e r s a L i n T x / 2 0 5 i v e r s a L i n...
-
Page 2: Table Of Contents
Table of Contenets INTRODUCTION............1 Overview ................1 System Requirements ........... 1 Unpacking ................1 Front Panel .................2 LED Status Indicator............2 INSTALLATION ............3 Step 1. Hardware Installation ........3 Step 2. Configure the IP Address ......4 WEB INTERFACE ............6 Login User Account ............ -
Page 3: Introduction
INTRODUCTION Overview The CyberPower Remote Management Card allows a UPS/ATS PDU system and environmental sensor to be managed, monitored, and configured. After installing the hardware and configuring an IP address, the user can access, monitor, and control the UPS/ATS PDU from anywhere in the world! Simply use a web browser or SSH client to access your UPS/ATS PDU. -
Page 4: Front Panel
Front Panel RMCARD205 RMCARD205 Universal Link Tx/Rx 1. Universal Port 2. Ethernet Port RMCARD305 3. Tx/Rx Indicator 4. Link Indicator RMCARD305 Universal Link Tx/Rx LED Status Indicators Link LED Condition The Remote Management Card is not connected to the Network / or the Remote... -
Page 5: Installation
INSTALLATION Step 1. Hardware Installation NOTE: The CyberPower Remote Management Card is hot-swappable, so you do not need to turn o the device to install it. RMCARD305 RMCARD205 1. Remove the two retaining screws of the expansion slot, and then remove the cover. -
Page 6: Step 2. Configure The Ip Address
Step 2. Configure the IP Address for the CyberPower Remote Management Card Method 1: Using the Power Device Network Utility 1. Install the Power Device Network Utility available for download at www.CyberPower.com. 2. After installation completes, run the “Power Device Network Utility”. - Page 7 Method 2: Using a Command Prompt NOTE: These instructions are for Windows OS. For other OS please refer to RMCARD User’s Manual available for download at CyberPower Systems o cal website: www.CyberPower.com. 1. Obtain the MAC address from the label on the Remote Management Card.
-
Page 8: Web Interface
WEB INTERFACE Login User Account You will need to enter a User Name and Password to login to the interface, and can select a preferred language after login. There are two user account types. 1. Administrator - Default username: cyber - Default password: cyber 2. -
Page 9: Using Upgrade And Configuration Utility Tool
Using Upgrade and Configuration Utility Tool (Bulk Firmware Upgrade Tool) 1. Install the CyberPower Upgrade and Configuration Utility tool available for download at www.CyberPower.com. 2. After installation completes, run the “Upgrade and Configuration Utility”. 3. The main window of the Upgrade and Configuration Utility tool program is shown in Figure 5. - Page 10 5. Select the devices you wish to upgrade by checking their respective checkbox and select “Upgrade Firmware”. NOTE: You can upgrade the firmware of multiple devices that use the same firmware files (Bulk firmware upgrade). 6. Select the Firmware and Data files and click “OK”, as shown in Figure 6.
- Page 11 8. If the firmware upgrade is implemented, you will see the Result in the main window, as shown in Figure 8. Figure 8. Firmware upgrade success in the main window...
-
Page 12: Reset To Factory Default Setting/Recover From A Lost Password
RESET TO FACTORY DEFAULT SETTING/RECOVER FROM A LOST PASSWORD To reset the CyberPower Remote Management Card to its factory default setting (including web log-in user name and password), please follow these steps: RESET JUMPER RMCARD205 RESET JUMPER RMCARD305 1. Remove the card from the UPS/ATS PDU without turning the UPS/ATS PDU o . -
Page 13: Rmcard Adapter Guide
RMCARD ADAPTER GUIDE Remove the adapter to convert an RMCARD305 to an RMCARD205 1. Remove the two screws from the adapter holding the card in place. 2. Remove the card from the adapter. 3. Remove the screw holding the RMCARD305 front panel to the card. - Page 14 Add the adapter to convert an RMCARD205 to an RMCARD305 1. Remove the screw holding the front panel to the card and remove the RMCARD205 front panel. 2. Screw on the RMCARD305 front panel to the card. 3. Install the card into the adapter.
-
Page 15: Software Support
NOTE: The RMCARD Adapter Kit is not included with the RMCARD205. Please contact CyberPower for ordering information or Technical Support. NOTE: RMCARD205 is designed for the 43x18mm (1.69x0.71 inch) SNMP card expansion port of CyberPower PR, OR, and 1-3kVA OL series UPS, and ATS PDU. -
Page 16: Troubleshooting
► Ensure the network connection is good. Address using method 2. Ensure the PC being used is on the same 1 or method 2 local network subnet as the CyberPower device you are trying to communicate with. 3. Ensure the Jumper on the Reset Pin is correctly installed. -
Page 17: Conformance Approvals
Reglement sur le materiel brouilleur du Canada. European Union This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. For warranty and additional information, please visit: www.cyberpower.com. - Page 18 Cyber Power Systems, Inc. www.cyberpower.com For USA and Canada: 4241 12th Ave East, Suite 400 Shakopee, MN 55379 Toll-free: (877) 297-6937 For all other regions: Please visit our website for local contact information. Copyright © 2017 Cyber Power Systems, Inc. All rights reserved.