Video and audio over ethernet standalone transmitter,
video and audio over ethernet pc card transmitter,
video and audio over ethernet receiver (29 pages)
Connects to the servswitch dkm dvi-d
kvm switch. (2 pages)
Summary of Contents for Black Box ME806A
Page 1
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) SUPPORT FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 INFORMATION Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: info@blackbox.com...
Page 2
FCC AND IC RFI STATEMENTS FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is...
Page 3
SHM-B PARALLEL-T, SHM-B PARALLEL -R NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
Page 4
E: El aparato ha sido tirado o su cubierta ha sido dañada. TRADEMARKS USED IN THIS MANUAL BLACK BOX and the logo are registered trademarks of Black Box Corporation. IBM, PC/AT, and PS/2 are registered trademarks, and PC/XT is a trademark, of International Business Machines Corporation.
SHM-B Parallel-R SHM-B Parallel-T (ME807A) (ME806A) • The SHM-B Parallel-T accepts parallel data from the PC, converts it to serial data, and sends the serial data over twisted-pair cable to the SHM-B. The SHM- B receives the serial data, converts it to RS-232 specifications, and sends the data to the RS-232 serial printer.
Page 9
SHM-B PARALLEL-T, SHM-B PARALLEL -R The SHM-B Parallel performs data transmission at bit rates from 1200 to 19,200 baud. It can be configured for either 7- or 8-bit word length and Even, Odd, or No parity. The SHM-B Parallel features advanced optically-isolated integrated circuitry, which eliminates damaging ground-loop currents and substantially reduces signal noise for improved data integrity.
CHAPTER 3: Installation 3. Installation 3.1 Standalone and Rackmount Versions The SHM-B Parallel is available in a standalone version and a rackmount version. The standalone transmitter and receiver are packaged in small, lightweight ABS plastic cases and equipped with wallmount transformers, for use on a desktop or shelf.
Page 11
SHM-B PARALLEL-T, SHM-B PARALLEL -R Remove the SHM-B card from the case or rack, exposing the terminal connector on the card. (For instructions on opening the standalone unit’s case, see step 2 in Section 3.6.) Strip ⁄ ⁄ inch of the insulation from the end of all four of the cable wires.
Page 12
CHAPTER 3: Installation SHM-B PARALLEL-T SHM-B TRANSMITTER RECEIVER Figure 3-3. Parallel-to-Serial Installation NOTE When operating serial to parallel or parallel to serial, the serial device has to run hardware flow control. Software flow control (X-ON/X-OFF, etc.) is not supported. 2. Test the Cabling To test the 4-wire cable and connections, remove the cable connecting the PC to the transmitter.
Page 13
SHM-B PARALLEL-T, SHM-B PARALLEL -R DB25 Centronics Connector Connector SHM-B Parallel-T Printer SHM-B Parallel-R 4-Wire IBM PC Twisted-Pair 25-Pin Straight-Through PC/Centronics Cable Cable (ECM25C) (EYN600) Figure 3-4. IBM PC to Printer Connection If your PC or other device (such as a mainframe computer) has a Centronics connector on the parallel output port, use the Centronics-to-DB25 female cable described in Table 3-1 to connect to the SHM-B Parallel transmitter.
SHM-B PARALLEL-T, SHM-B PARALLEL -R In the idle condition, the TD and the RD LEDs will light green. When transmitting, they will light green and red. When the printer cannot accept any more data, the Busy LED on the transmitter and on the receiver will light red and the data transmission will stop.
Page 16
CHAPTER 3: Installation installed. To remove the faceplate and expose the card, apply pressure at the top front of the unit to separate the top and the bottom halves of the case, then push on the rear connector to force out the front panel and printed circuit assembly.
SHM-B PARALLEL-T, SHM-B PARALLEL -R 4. Troubleshooting Before installing the SHM-B Parallel, verify that the source of the parallel data works correctly with the destination equipment when no modem link is installed. This isn’t always possible, but be certain that all equipment is plugged-in and powered on, and that all cables are securely connected.