Related Manuals for Black Box MEDIACENTO IPX 4K
Summary of Contents for Black Box MEDIACENTO IPX 4K
- Page 1 STEP X - Name of Step QUICK START GUIDE VX-HDMI-4KIP-TX, VX-HDMI-4KIP-RX MEDIACENTO IPX 4K 24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM...
-
Page 2: Step 1 - Check The Package Contents
STEP 1 - Check the Package Contents VX-HDMI-4KIP-TX PACK AGE CONTENTS VX-HDMI-4KIP-RX PACK AGE CONTENTS • (1) MEDIACENTO IPX 4K TRANSMITTER • (1) MEDIACENTO IPX 4K RECEIVER • (1) 5-VDC, 3-A POWER SUPPLY • (1) 5-VDC, 3-A POWER SUPPLY • (1) IR BLASTER CABLE •... - Page 3 STEP 2A - Transmitter (TX) Front Panel 2 3 4 TABLE 2. TRANSMITTER FRONT PANEL COMPONENTS NUMBER IN COMPONENT DESCRIPTION DIAGRAM ABOVE Serial over IP RS-232 extension port, connects to source DB9 connector device Power ON Status LED Lights steady when power on sequence is completed Link LED Indicates LAN Link status Set/Reset button...
- Page 4 STEP 2A (CONTINUED) - Transmitter (TX) Front Panel 2 3 4 TABLE 2 (CONTINUED). TRANSMITTER FRONT PANEL COMPONENTS NUMBER IN COMPONENT DESCRIPTION DIAGRAM ABOVE IR Emitter connector Used for emitting signal of IR extension over IP IR Receiver connector Used for receiving signal of IR extension over IP Audio connector Connects to analog audio output (speaker) Audio connector...
- Page 5 STEP 2B - Transmitter (TX) Back Panel TABLE 3. TRANSMITTER BACK PANEL COMPONENTS NUMBER IN COMPONENT DESCRIPTION DIAGRAM ABOVE SFP cage Fiberoptic module for link between TX and RX installs here RJ-45 connector Used for LAN Link between TX and RX/Gigabit Ethernet switch HDMI IN connector Connects to HDMI source for HDMI extension over IP HDMI OUT connector...
- Page 6 STEP 3A - Receiver (RX) Front Panel 2 3 4 TABLE 4. RECEIVER FRONT PANEL COMPONENTS NUMBER IN COMPONENT DESCRIPTION DIAGRAM ABOVE DB9 connector Serial over IP RS-232 extension port, connects to sink device Power ON Status LED Lights steady when power on sequence is completed Link LED Indicates LAN Link status SFP LED...
- Page 7 STEP 3A (CONTINUED) - Receiver (RX) Front Panel TABLE 4 (CONTINUED). RECEIVER FRONT PANEL COMPONENTS NUMBER IN COMPONENT DESCRIPTION DIAGRAM AT LEFT CH+/CH- pushbuttons Press to change video channel IR Emitter connector Used for emitting signal of IR extension over IP IR Receiver connector Used for receiving signal of IR extension over IP Audio connector...
- Page 8 STEP 3B - Receiver (RX) Back Panel TABLE 5. RECEIVER BACK PANEL COMPONENTS NUMBER IN COMPONENT DESCRIPTION DIAGRAM ABOVE SFP cage Fiberoptic module for link between TX and RX installs here RJ-45 connector Used for LAN Link between TX and RX/Gigabit Ethernet switch HDMI OUT connector Connects to HDMI sink for HDMI extension over IP 5-VDC jack...
-
Page 9: Step 4 - Network Setup And Hardware Switching
STEP 4 - Network Setup and Hardware Switching NETWORK SETUP AND HW SWITCHING 7. Plug-in a DC power adapter to all transmitters 1. Power on the Gigabit Switch and enable and receivers. The units power on. Jumbo Frame (8k) and IGMP v2. 8. -
Page 10: Step 5 - Remote Control
STEP 5 - Remote Control USING THE REMOTE CONTROL To use the 99-channel IR remote controller, follow steps A through C below. A. Press “CH+” or “CH-“ to scroll to the next or previous available video channel. B. Press the number key “1” – “0” and “ENTER” to directly change to the specific video channel. -
Page 11: Reset To Factory Default
4. Click on the “Support” tab on the product page, and select the document you wish to download. If you have any trouble accessing the Black Box site to download the manual, you can contact our Technical Support at 877-877-2269... - Page 12 STEP X - Name of Step COPYRIGHT 2017 BLACK BOX CORPORATION. ALL RIGHTS RESERVED.