Lionel Command Control Gantry Crane Owner's Manual
  1. Manuals
  2. Brands
  3. Lionel Manuals
  4. Toy
  5. Command Control Gantry Crane
  6. Owner's manual

Lionel Command Control Gantry Crane Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

78-2097-250
9/16
Lionel
Lionel
Command Control
Command Control
Gantry Crane
Gantry Crane
Owner's Manual
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Command Control Gantry Crane and is the answer not in the manual?

Questions and answers

Related Manuals for Lionel Command Control Gantry Crane

Summary of Contents for Lionel Command Control Gantry Crane

  • Page 1 78-2097-250 9/16 Lionel Lionel Command Control Command Control Gantry Crane Gantry Crane Owner’s Manual Owner’s Manual...
  • Page 2 CAB-1 or CAB-2 Remote Controller. ElectroCouplers™, basic sounds, and multiple unit lash-ups are all at your fingertips as you walk around your layout. The following Lionel marks are used throughout this Owner’s Manual and are protected under law. All rights reserved. ®...

  • Page 3: Table Of Contents

    Assigning a new ID# to your Gantry Crane Operating the Gantry Crane Capabilities of the Gantry Crane Operating the Gantry Crane CAB-2 Remote Controller commands CAB-1 and CAB-1L Remote Controller commands Maintenance and Service Storing the Gantry Crane Lionel Limited Warranty Policy & Service...

  • Page 4: Gantry Crane Basics

    Gantry Crane basics Preparing the Gantry Crane for operation hen you are ready to store your Gantry Crane, be sure to use the supplied elastic band to keep tension on the hook line. Use your remote to position the boom to fit in the foam cavity. Note Always keep light tension on the hook when handling the Gantry Crane.

  • Page 5: Assigning A New Id To Your Gantry Crane

    Gantry Crane basics Assigning a new ID to your Gantry Crane s your fleet of LEGACY or TMCC equipped locomotives and equipment grows, you will want to assign each unit a unique ID#. Use your CAB-1, CAB-1L, or CAB-2 Remote Controller. When using the Legacy system the CAB-2 MUST be set to CAB-1 mode.
  • Page 6 Gantry Crane basics Operating the Gantry Crane o operate the crane, you will need to use a Command Base and Remote Controller (LEGACY CAB-2, CAB-1L, or CAB-1; all available separately). Operating the Cab Motor Press ENG and 1 on the CAB-1, CAB-1L, or CAB-2 controller to select the Cab motor. Cab-1 or Cab-1L remote LEGACY remote Rotate the THROTTLE knob clockwise on the CAB-1, CAB-1L, or...
  • Page 7 Gantry Crane basics Operating the Gantry Crane continued Operating the Roll Motor Press 2 on the CAB-1, CAB-1L, or CAB-2 controller to select the Roll motor. Cab-1 or Cab-1L remote LEGACY remote Rotate the THROTTLE knob clockwise on the CAB-1, CAB-1L, or CAB-2 controller to make the Gantry Crane roll forward.
  • Page 8 Gantry Crane basics Capabilities of the Gantry Crane our Gantry Crane’s hook and electromagnet are capable of lifting approximately 4 oz (1/4 lb). The electromagnet automatically turns off after 60 seconds. The electromagnet cannot be turned on again for 8 seconds. Operating the Hook Motor Press the BOOST key on the CAB-1, CAB-1L, or CAB-2 controller to raise the hook.

  • Page 9: Operating The Gantry Crane

    Operating the Gantry Crane The LEGACY CAB-2 Remote Controller se your CAB-2 Remote Controller to operate your Gantry Crane. Sets the throttle knob to control the roll motion of the cab. Sets the throttle knob to rotate the cab. Toggles the electromagnet on and off.

  • Page 10: Operating The Gantry Crane

    Operating the Gantry Crane CAB-1 & CAB-1L Remote Controller commands se your CAB-1 Remote Controller to operate the Gantry Crane. Sets the throttle knob to rotate the cab. Sets the throttle knob to control the roll motion of the crane. Moves the crane back and forth along the gantry track or rotates the cab.

  • Page 11: Maintenance And Service

    Maintenance and Service Storing the Gantry Crane hen you are ready to store your Gantry Crane, be sure to use the supplied elastic band to keep tension on the hook line. Position the boom manually using the rotating knob at the rear of the crane cab to fit in the foam cavity.

  • Page 12: Lionel Limited Warranty Policy & Service

    Lionel LLC or any Lionel Authorized Service Station MUST be accompanied by the original receipt for purchase (or copy) from an Authorized Lionel Retailer*, will at the discretion of Lionel LLC, be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a suitable replacement is not available, Lionel will offer to replace the product with a comparable model (determined by Lionel LLC), if available.

Table of Contents