Using The Osd; Current Status Display; Osd Menu Settings - Sherwood RD-8601 Operating Instructions Manual

Using the OSD

This unit incorporates an OSD(On-screen display) function to provide information about basic operation of this unit and to simplify
the setup procedures.
The OSD function uses a monitor TV connected to this unit as a display and has two kinds of display modes such as current status
display and menu screen.
■Notes: • Any on-screen display shown on the monitor TV will not be recorded.
• Because this unit cannot support the OSD function for the progressively scanned video signal, the OSD for current status
and menu settings may be displayed abnormally or may not be displayed.

CURRENT STATUS DISPLAY

This mode shows the status corresponding to each operation.
• The on-screen display will automatically disappear in several seconds.
• For examples, there are 2 status displays as follows.
Notes
• When watching a movie earnestly, if you want to turn off the current status display function, set the OSD auto display mode to
Off(For details, refer to "When selecting the AUTO OSD" on page 41)
※Current status display function might not operate as expected if :
• You view a movie via MONITOR COMPONENT OUTs while component video signals are input into this receiver.
• You view a movie via MONITOR COMPOSITE OUT while S-Video signals and composite video signals are input into this receiver.
When selecting the desired input source
V I D EO 1 ( OP T I CA L 1 )
Input source Signal input

OSD Menu Settings

• The OSD menu allows you to perform the setup procedures easily. In most situations, you will only need to set this once during
the installation and layout of your home theater, and it rarely needs to be changed later. The OSD menu consists of 5 main menus :
speaker setup, function select, surround mode, CH level setup and auto OSD. Some of these menus are divided into sub-menus.
• The OSD menu settings are performed easily with the CURSOR control(▲, ▼, ◀, ▶), OSD and ENTER buttons.
■Notes :
• In such a case of making only COMPONENT VIDEO connections between this receiver and video component, while viewing a
movie via the MONITOR COMPONENT OUTs, if the OSD menu operation is performed, the picture is automatically turned off
and only the OSD menu is displayed.
• When S-Video signals and composite video signals are input into this receiver, even though the OSD menu operation is performed,
the OSD menu cannot be displayed via MONITOR COMPOSITE OUT.
Turn the menu screen on.
1
• The main menu will be shown.
• To turn the menu screen off, press this button again.
POWER ON STANDBY
AUD CD CD AUX AUX TV TV
VCR VCR DVD DVD SA SAT CBL CBL
DEVICE SELECT
OSD
CH.SEL CH.SEL
T/V T/V
CH/LEVEL CH/LEVEL MUTE MUTE VOLUME
T.TONE .TONE OSD OSD
MENU MENU PTY SELECT PTY SELECT SETUP SETUP
RDS
ENTER
SLEEP SLEEP SEARCH MODE SEARCH MODE DIMMER DIMMER
SETUP
DISPLA DISPLAY RETURN RETURN
TUNE TUNE TUNE TUNE
PRESET PRESET P .SCAN .SCAN PRESET PRESET
AUTO AUTO DSP DSP STEREO STEREO
SPK SET SPK SET ADJUST ADJUST
PARAMA ARAMATER TER
TUNER CD AUX TAPE
1 2 3 4
VIDEO 1 VIDEO 2 VIDEO 3
5 6 7 8
EXT. IN
9 0 +10 +10
MACRO MACRO
M1 M1 M2 M2 M3 M3
REMOTE CONTROL RNC-55A REMOTE CONTROL RNC 55A
POWER ON STANDBY
CD AUX TV
VCR DVD SAT CBL
CH.SEL
T/V
CH/LEVEL
MUTE
T.TONE OSD
MENU PTY SELECT SETUP
RDS
ENTER
When selecting the TEST TONE mode
F L
C F R
SW
S L S B SR
F L - - - - - - - - - - - - - - 0
• When adjusting overall volume, the volume level display will be shown.
• The test tone display will be shown until the test tone mode is canceled.
MA I N MENU
SP E A K ER S E T UP
F UNC T I ON S E L E C T
SURROUND MODE
CH L E V E L
AU TO OSD
: MOV E
O S D : E ND
• In the bottom of the display, "OSD" stands for the OSD
button. "ENTER" for "ENTER", "▲", "▼", "◀", and
"▶" for CURSOR UP(▲), DOWN(▼), LEFT(◀) and
RIGHT(▶).
40
Channel level or
master volume
display
S E T U P
: ON
E N T E R : S E L .