Sherwood RD-8601 Operating Instructions Manual page 23

Specify the setting condition.
4
When specifying the number of speakers installed.
SPEAKER
SETUP
or
SPK SET
When specifying the subwoofer or the crossover frequency.
ADJUST
or
ADJUST
Start the auto speaker setup procedure.
5
MEMO/ENTER
or
Notes:
• Because the test tones are very loud, ensure there
are no infants or small children in the room.
• For best results, ensure the room is as quiet as
possible during the auto speaker setup procedure.
If there is too much ambient noise, the results may
not be satisfactory.
• Each time this button is pressed, the speaker layout changes
as follows:
POWER ON POWER ON STANDBY
AUD CD CD AUX AUX TV TV
VCR VCR DVD DVD SA SAT CBL CBL
DEVICE SELECT
CH.SEL CH.SEL
T/V T/V
CH/LEVEL CH/LEVEL
MUTE MUTE VOLUME
T.TONE .TONE OSD OSD
MENU MENU SETUP SETUP
ENTER
SLEEP SLEEP DIMMER DIMMER
DISPLAY DISPLA RETURN RETURN
TUNE TUNE TUNE TUNE
PRESET PRESET P .SCAN .SCAN PRESET PRESET
AUTO AUTO DSP DSP STEREO STEREO
SPK SET SPK SET ADJUST ADJUST PARAMATER
TUNER CD AUX TAPE
1 2 3 4
VIDEO 1 VIDEO 2 VIDEO 3
5 6 7 8
EXT. IN
9 0 +10 +10
MACRO MACRO
M1 M1 M2 M2 M3 M3
REMOTE CONTROL RNC-50A REMOTE CONTROL RNC 50A
• Each time the ADJUST UP(▲) or CURSOR RIGHT(▶)
button is pressed, the subwoofer changes as follows:
POWER ON STANDBY
AUD CD CD AUX AUX TV TV
POWER ON VCR VCR DVD DVD STANDBY SA SAT CBL CBL
CD AUX TV
DEVICE SELECT
VCR DVD SAT CBL
CH.SEL CH.SEL
T/V T/V
CH/LEVEL CH/LEVEL MUTE MUTE VOLUME
CH.SEL
.TONE T.TONE T/V OSD OSD
CH/LEVEL MUTE
MENU MENU PTY SELECT PTY SELECT SETUP SETUP
T.TONE RDS OSD
ENTER
• Each time the ADJUST DOWN(▼) or CURSOR LEFT(◀)
MENU SETUP
SLEEP SLEEP SEARCH MODE SEARCH MODE DIMMER DIMMER
DISPLAY DISPLA ENTER RETURN RETURN
TUNE TUNE TUNE TUNE
SLEEP DIMMER
PRESET PRESET .SCAN P .SCAN PRESET PRESET
DISPLAY RETURN
button is pressed, the crossover frequency("CUT") changes
TUNE TUNE
PRESET P .SCAN PRESET
AUTO DSP STEREO STEREO
SPK SET SPK SET ADJUST ADJUST PARAMATER
AUTO DSP STEREO within the range of 40~130 Hz in 10 Hz intervals.
TAPE
TUNER CD AUX
1 2 3 4
SPK SET ADJUST PARAMATER
VIDEO 1 VIDEO 2 VIDEO 3
5 6 7 8
EXT. IN
1 2 3 4
9 0 +10 +10
• In case that the subwoofer setting is "S"(Subwoofer:Yes), if
5 6 7 8
MACRO MACRO
9 0 +10
M1 M1 M2 M2 M3 M3
MACRO
REMOTE CONTROL RNC REMOTE CONTROL RNC-55A 55A
M1 M2 M3 it is possible to adjust the volume and crossover frequency
REMOTE CONTROL RNC-50A
on your subwoofer, set the volume to about medium level
(or slightly less), and set the crossover frequency to the
maximum.
• Loud test tones are output from each speaker.
POWER ON POWER ON STANDBY ANDBY • To stop the auto speaker setup procedure, press the
AUD CD CD AUX AUX TV TV
VCR VCR DVD DVD SAT SA CBL CBL
DEVICE SELECT
CH.SEL CH.SEL
T/V T/V
CH/LEVEL CH/LEVEL MUTE MUTE VOLUME
T.TONE .TONE OSD OSD
MENU MENU SETUP SETUP
ENTER
ENTER
SLEEP SLEEP DIMMER DIMMER
DISPLA DISPLAY RETURN RETURN
TUNE TUNE TUNE TUNE
PRESET PRESET P .SCAN .SCAN PRESET PRESET
AUTO AUTO DSP DSP STEREO STEREO
•After the auto speaker setup procedure has been completed,
SPK SET SPK SET ADJUST ADJUST PARAMATER
TUNER CD AUX TAPE
1 2 3 4
VIDEO 1 VIDEO 2 VIDEO 3
5 6 7 8 "SET MEMO" will be displayed.
EXT. IN
9 0 +10 +10
MACRO MACRO
M1 M1 M2 M2 M3 M3
• If ">ERROR<" is displayed, there may be a problem with
REMOTE CONTROL RNC REMOTE CONTROL RNC-50A 50A
• If retrying the procedure does not fix the problem, turn off
23
ALL : All speakers
3/2 : 2 front, center and 2 surround speakers
2/2 : 2 front and 2 surround speakers
3/0 : 2 front and center speakers
2/0 : 2 front speakers
S No display
(Subwoofer: Yes) (None)
(MEMORY/) ENTER button.
To retry the procedure, press the (MEMORY/) ENTER
button again.
the speaker or microphone connection.
While displaying ">ERROR<", to retry the procedure,
press the ADJUST UP(▲) or CURSOR RIGHT(▶) button
and to exit from the procedure, press the ADJUST
DOWN(▼) or CURSOR LEFT(◀) button.
the power and check the speaker or microphone
connections.