Advertisement
1988-92 Mazda MX-6 (Coupe)
1988-92 Mazda 626 (Sedan)
Radio Removal:
1. Remove ashtray and pocket. (Pocket slides out.)
2. Remove four Phillips head sheet metal screws securing
the radio trimpanel, two from the ashtray location and
two from the pocket location.
3. Carefully, remove the radio trimpanel, disconnect the
illumination light, the lighter plug, then
remove the trimpanel.
4. Remove four Phillips head sheet metal screws securing
the radio/EQ, pull radio out, disconnect antenna lead,
wire harnesses, then remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
1986-92 Mazda RX-7
Radio Removal:
1. Carefully, pry up on the shifter
trimplate to release snap clips
BRACKET C
and move trim towards rear
HOLE 7 WITH SPACER
of car.
2. Remove ashtray and extract
two screws from behind the
ashtray.
3. Gently, pull bottom of radio trimpanel
away from dash.
4. Reach behind right lower corner of the
trim panel and disconnect the slip-on
terminal and the twist-type light socket
from the cigarette lighter.
5. Gently, pull bottom of the ventilation duct
trim away from the dash to access metal
clips which are located on each side of the
duct. Insert a thin metal strip (feeler gauge,
metal ruler, etc.) along each side of the trim
to release the clips.
6. Remove two screws from behind the duct
trim at the top of the radio trimpanel.
Carefully (evenly) pull the radio trimpanel
away from the dash to release the metal
clips and remove the radio trim.
7. Remove four screws which secure radio to dash, slide radio out of dash cavity, disconnect wiring harness and antenna
lead. Remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
1984-85 Mazda RX-7 (Coupe)
Radio Removal:
1. Using panel removal tool, carefully pry up on
edges of trimpiece which covers
shift lever to release snapclips, lift
USE BRACKET 4
trimpiece up and rotate trim 90
WITH SPACER
degrees.
2. Remove two Phillips head sheet metal screws
from bottom of radio trimpanel.
3. Remove two air-conditioning control knobs, then
remove two shaftnuts from air-conditioning shafts.
4. Remove radio trimpanel.
5. Remove four Phillips head sheet metal screws
which secure radio equalizer assembly to dashboard,
then slide radio assembly out of dash.
6. Disconnect power antenna, speaker and all electrical
connections, then remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
SCOSCHE STEREO INSTALLATION COMPONENTS
USE BRACKET 3 WITH SPACER
PANEL A
USE BRACKET 5
FRONT VIEW
TRIM PANEL E
CUT OFF AT THE SECOND CUT LINE FROM TOP.
CUTLINES ARE ON THE BACK OF PANEL
BRACKET C
BRACKET B
HOLE 7 WITH
HOLE 7 WITH SPACER
SPACER
CUT
TOP VIEW
PANEL A
FRONT VIEW
PANEL B
CUT
BRACKET G
HOLE 4
BRACKET G
BRACKET F
BRACKET F
HOLE 4
HOLE 4
HOLE 4
USE BRACKET 4 WITH SPACER
PANEL A
FRONT VIEW
PANEL B
USE BRACKET A HOLE 4
DIN RADIO INSTALLATION (DETACHABLE FACE/PULLOUT)
Before installing a DIN radio, the shaft support sections of panel A or C need to
be removed. Remove the front panel shaft sections as shown. Following the
USE BRACKET 5
cut lines with side cutters, an X-acto knife, a hacksaw blade or wire cutters
and cut out the two sections. Use caution with sharp tools
and cut away from yourself. Insert the DIN radio's mounting
sleeve and bend the tabs as shown.
SIDE VIEW
1986-93 Mazda B2000
Radio Removal:
1. Remove ashtray, then remove one 10mm
hex head screw from behind.
2. Remove two Phillips head sheet
BRACKET B
metal screws from each side
HOLE 7 WITH
of console.
SPACER
3. Pull console away from mounting
position and disconnect four
electrical plugs.
4. Radio is secured to console from
behind. Remove four Phillips head sheet
metal screws which secure radio/bracket assembly to console
shell and two from above radio. Slide radio assembly out of console shell.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
BOTTOM VIEW
1990-97 Mazda Miata
Radio Removal:
1. Open the center console
storage opening and extract
the two screws from this location.
2. Pull out the ashtray and remove the
single screw from this location.
3. Remove one screw from each side of
center console (two screws total), located
along front portion of console.
4. Take off the shift knob and remove
the center console from the car.
5. Extract the single screw from the lower
left side of the radio console.
6. Carefully pop out the air vents, gently pry at each side to release the spring type securing clips.
7. Remove one screw from behind each vent location (two screws total).
8. Remove the radio console trim panel.
9. Extract the four screws securing the factory radio to the dash. Pull the unit out of the cavity, disconnect all connectors,
then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
1989-95 Mazda MPV (Van)
SIDE VIEW
Radio Removal:
1. Remove the ashtray, then extract two screws
from this location.
BOTTOM VIEW
2. Carefully release the trim panel fasteners and
pull back the trim panel, disconnect the lighter
connectors and remove the trim.
3. Extract four screws securing the radio to the
dash - two located at the top and two at the
CUT
bottom.
4. Pull the radio out of the cavity, disconnect the
wire harness, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
MOUNTING THE RADIO
CUT BRACES OUT
DIN CUT LINES
RADIO'S
(REAR VIEW OF KIT)
SUPPLIED
TRIMPLATE
DIN RADIO
CAUTION:
REAR SUPPORT AVAILABLE
SEPARATELY. REAR SUPPORTING
THE RADIO ADDS TO THE
INSTALLATIONS STRUCTURAL
INTEGRITY.
PANEL A
USE BRACKET 4
BRACKET F
USE HOLE 5
PANEL B
CUT
FRONT VIEW
USE BRACKET S WITH HOLE 1
USE
BRACKET R
WITH HOLE 1
PANEL A
FRONT VIEW
PANEL B
USE BRACKET A WITH HOLE 6
USE BRACKET 1
PANEL A
FRONT VIEW
TRIM PANEL E
CUT OFF AT THE SECOND CUT LINE FROM THE TOP.
CUTLINES ARE ON THE BACK OF THE PANEL
REAR SUPPORT STRAP
MOUNTING
PANELS A & B
BEND TABS
OUTWARD
RADIO SLEEVE
USE
BRACKET 4
SIDE VIEW
CUT
BRACKET G USE HOLE 6
USE BRACKET R
WITH HOLE 1
TOP VIEW
USE BRACKET S
WITH HOLE 1
CUT
USE BRACKET A
WITH HOLE 6
SIDE VIEW
SIDE VIEW
STEREO DASH KITS
Advertisement
