Scosche MA2030 Installation Instructions

IN-DASH INSTALLATION KIT FOR
1984-UP MAZDA VEHICLES
INTRODUCTION / PRELIMINARY
Thank you for purchasing the Scosche MA2030 Kit. This kit was manufactured with the highest of quality
standards.
CAUTION:
DISCONNECT YOUR VEHICLE'S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT
ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER OVER A TEST LIGHT TO CHECK
WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE'S COMPUTER AND/
OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIR BAG WIRING - AIR BAGS CAN ACCIDENTALLY DEPLOY
CAUSING SERIOUS INJURY OR DEATH.
NOTES:
•
See your vehicle's instructions for any special tools your installation might require.
•
Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting instructions.
PRELIMINARY PARTS LIST
Your kit includes:
• 1 Mounting Panel A • 1 Mounting Panel B
• 1 Trim Panel G • 1 Trim Panel E
• 2 Spacers • Mounting Hardware
ASSEMBLING THE KIT
This kit can be assembled in several different configurations, first refer to the applications
list to find your vehicle and then follow the listed directions.
ATTACHING THE PANELS
Some installations require two or more panels to be attached together. To attach panels
together, simply line up the tabs and slots between the kit panels and press them together.
(See illustration A.)
ATTACHING THE BRACKETS
Some installations require that you attach
specific brackets to the mounting panels.
Before attaching bracket to the top,
bottom, or sides of the mounting panels,
there are molded-on numbered tabs that will
have to be removed. Use cutters or
simply bend the tabs back and forth until they
come off. (See illustration B.)
USE THE SHADED TABS AND
CUT OFF THE REMAINING
ILLUSTRATION B
PANEL A
PANEL B
• 1 Mounting Panel C • 1 Trim Panel F
• 1 Panel Spacer D • 20 Brackets (A-S)
• Instruction Book
ILLUSTRATION A
PANEL B
NUT
BRACKET A
CINCH STUDS
BRACKET O
NUT
BRACKET O
HOLE #2
CINCH STUDS
MA2030 MA2030 MA2030 MA2030 MA2030
DIN RADIO INSTALLATION (DETACHABLE FACE/PULLOUT)
Before installing a DIN radio, the shaft support sections of panel A or C need to
be removed. Remove the front panel shaft sections as shown. Following the
cut lines with side cutters, an X-acto knife, a hacksaw blade or wire cutters
and cut out the two sections. Use caution with sharp tools
and cut away from yourself. Insert the DIN radio's mounting
sleeve and bend the tabs as shown.
1986-93 Mazda B2000
Radio Removal:
1. Remove ashtray, then remove one 10mm
hex head screw from behind.
2. Remove two Phillips head sheet
metal screws from each side
of console.
3. Pull console away from mounting
position and disconnect four
electrical plugs.
4. Radio is secured to console from
behind. Remove four Phillips head sheet
metal screws which secure radio/bracket assembly to console
shell and two from above radio. Slide radio assembly out of console shell.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
1990-97 Mazda Miata
Radio Removal:
1. Open the center console
storage opening and extract
the two screws from this location.
2. Pull out the ashtray and remove the
single screw from this location.
3. Remove one screw from each side of
center console (two screws total), located
along front portion of console.
4. Take off the shift knob and remove
PANEL A
the center console from the car.
5. Extract the single screw from the lower
left side of the radio console.
6. Carefully pop out the air vents, gently pry at each side to release the spring type securing clips.
7. Remove one screw from behind each vent location (two screws total).
8. Remove the radio console trim panel.
9. Extract the four screws securing the factory radio to the dash. Pull the unit out of the cavity, disconnect all connectors,
then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
1989-95 Mazda MPV (Van)
Radio Removal:
1. Remove the ashtray, then extract two screws
from this location.
2. Carefully release the trim panel fasteners and
pull back the trim panel, disconnect the lighter
connectors and remove the trim.
3. Extract four screws securing the radio to the
dash - two located at the top and two at the
bottom.
4. Pull the radio out of the cavity, disconnect the
wire harness, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
MOUNTING THE RADIO
CUT BRACES OUT
DIN CUT LINES
RADIO'S
(REAR VIEW OF KIT)
SUPPLIED
TRIMPLATE
DIN RADIO
CAUTION:
REAR SUPPORT AVAILABLE
SEPARATELY. REAR SUPPORTING
THE RADIO ADDS TO THE
INSTALLATIONS STRUCTURAL
INTEGRITY.
PANEL A
USE BRACKET 4
BRACKET F
USE HOLE 5
PANEL B
CUT
FRONT VIEW
USE BRACKET S WITH HOLE 1
USE
BRACKET R
WITH HOLE 1
PANEL A
FRONT VIEW
PANEL B
USE BRACKET A WITH HOLE 6
USE BRACKET 1
PANEL A
FRONT VIEW
TRIM PANEL E
CUT OFF AT THE SECOND CUT LINE FROM THE TOP.
CUTLINES ARE ON THE BACK OF THE PANEL
REAR SUPPORT STRAP
MOUNTING
PANELS A & B
BEND TABS
OUTWARD
RADIO SLEEVE
USE
BRACKET 4
SIDE VIEW
CUT
BRACKET G USE HOLE 6
USE BRACKET R
WITH HOLE 1
TOP VIEW
USE BRACKET S
WITH HOLE 1
CUT
USE BRACKET A
WITH HOLE 6
SIDE VIEW
SIDE VIEW