Table of Contents
Advertisement
Quick Links
HAMMER DRILL / DRIVER
18 VOLT
Model 91007
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
®
Copyright 2004 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Chicago Electric 91007
Summary of Contents for Chicago Electric 91007
- Page 1 HAMMER DRILL / DRIVER 18 VOLT Model 91007 OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com ® Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
-
Page 2: Product Specifications
Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. SKU 91007 PAGE 2... -
Page 3: Electrical Safety
Do not use a power tool while tired or under the influ- ence of drugs, alcohol, or medication. A moment of inattention while operat- ing power tools may result in serious personal injury. SKU 91007 PAGE 3... - Page 4 Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. SKU 91007 PAGE 4...
-
Page 5: Grounded Tools: Tools With Three Prong Plugs
The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.) SKU 91007 PAGE 5... -
Page 6: Double Insulated Tools: Tools With Two Prong Plugs
Underwriters Laboratories, Inc., the CanadianStandard Association, and the National Electrical Code. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) FIGURE B SKU 91007 PAGE 6... -
Page 7: Extension Cords
2.1 – 3.4 3.5 – 5.0 5.1 – 7.0 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE C SKU 91007 PAGE 7... -
Page 8: Specific Safety Rules
Make sure to unplug the Battery Charger from its outlet before leaving the work area. Use eye protection. Always wear ANSI approved safety impact eye goggles when working with this product. Proper Battery Care: Battery (28) leakage may occur under extreme usage or SKU 91007 PAGE 8... - Page 9 Severe heat is most destructive to a Battery. The more heat generated, the faster the Battery loses power. A Battery that gets too hot can be permanently damaged. Never over-discharge a Battery by using the tool even after tool SKU 91007 PAGE 9...
- Page 10 (California Health & Safety Code 25249.5, et seq. ) SKU 91007 PAGE 10...
- Page 11 Once the Battery (28) is fully charged, disconnect the Battery Charger (33) from the electrical outlet. Then, disconnect the Charger Plug from the Battery (See Figure E.) NOTE: If charging more than one Battery (28), allow the Battery Charger (33) to cool down before reusing. SKU 91007 PAGE 11...
- Page 12 Use the Forward/Reverse Switch only after the Hammer Drill/Driver has come to a complete stop. (See Figure F.) CHUCK SLEEVE IMPACT CLUTCH (6) TORQUE ADJUSTER (17) CHUCK (4) FORWARD/REVERSE SWITCH (29) TRIGGER SWITCH (26) CARRYING STRAP (31) BATTERY (28) FIGURE F SKU 91007 PAGE 12...
- Page 13 Press the Forward/Reverse Switch (29) for the direction of rotation desired. (See Figure F.) Set the Torque Adjuster (17) to the desired position. (See Figure F.) SKU 91007 PAGE 13...
- Page 14 Remove the Drill Bit (34) from the Hammer Drill/Driver, and store the Drill Bit in its Carrying Case (37). Store the Hammer Drill/Driver in its Carryng Case (37), and store the Carrying Case in a safe, clean, dry location. SKU 91007 PAGE 14...
-
Page 15: Inspection, Maintenance, And Cleaning
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 91007 PAGE 15... -
Page 16: Parts List
Carrying Case Bit Holder Plate ASSEMBLY DIAGRAM 24 25 21 22 14 15 12 13 10 11 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 91007 PAGE 16...
Need help?
Do you have a question about the 91007 and is the answer not in the manual?
Questions and answers