Advertisement
Quick Links
Waterproof Battery to Battery Charger 60A-180A models
BBW1260 60A 12V to 12V
BBW12180 180A 12V to 12V
New model from March 2015
For latest instructions regarding
this model refer to
sterling-power.com
Revised
February 2015
S
TERLI G
P
OWER
- User Manual
BBW12120 120A 12V to 12V
4
technology
RoHS
ProDigital
compliant
IP68
Waterproof
Electronics
Fan is IP65
e
24
Magnetic field
warning:
There is a small magnet fitted in the lid of this
product under the label marked 'magnetic
area'. With the vast majority of installations
this will have no effect on anything, however,
this magnet may influence a magnetic
susceptible product such as a magnetic
compass. Please check your magnetic
sensitive products after installation of this
device. If there is an adverse effect then you
can peel back the lower section of the label on
the lid of the product and remove the magnet.
languages
Regenerative
B
raking riendly
F
R.B.F
Smart Alternator
Regenerative
Braking Friendly
Absorption
Condi
H Charge
Float
Sterling Power Products
V
12.2
In / Unit
Out / Rem
Audible alarm on/off
Batt.
hold >3 sec
Temp
Volts
Unit on/off
Menu
Select
Change
hold > 3 sec
Fault
Optional
remote control
instructions inside
1 x temp sensor
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Sterling Power BBW1260
Summary of Contents for Sterling Power BBW1260
-
Page 1: User Manual
Unit on/off Menu Select Change hold > 3 sec Fault Optional remote control instructions inside BBW1260 60A 12V to 12V BBW12120 120A 12V to 12V IP68 Waterproof Electronics Fan is IP65 1 x temp sensor Magnetic field warning: There is a small magnet fitted in the lid of this product under the label marked ‘magnetic... - Page 2 Copyrights © 1993-2013 Sterling Power Ltd. chemistry profiles between 14.0-15.5V - consult All Rights Reserved battery manufacturer). A rule of thumb: Higher voltages result in faster charging and lower voltage Contents Page result in slower charging. After a period of time, calculated by the software, when the auxiliary Page 2 - About the battery to battery charger.
- Page 3 12V 120A model 12V 60A model Negative Negative Fan Power Fan Power Positive Positive Aluminium Aluminium Heat sink Heat sink 40 mm 40 mm Aluminium Heat sink 40 mm 19 18 1) Main positive DC power output to auxiliary battery. 2) Low Voltage ( regenerative braking ) ->...
- Page 4 Basic Battery installation drawing remote control Absorption Condi Negative H Charge Float Sterling Power Products Positive 12.2 In / Unit Out / Rem Audible alarm on/off Batt. hold >3 sec Temp Volts Menu Unit on/off Heat sink Select Change hold >...
- Page 5 Installation Please note, as soon as you do this, any pre-stored battery type setting is removed and we start from Set this unit as you would any other high power battery battery type 1 (GEL USA refer to table on the RHS). charger.
- Page 6 To setup battery type: (from first install) the input negative and follow the same instructions. battery must be over 10.0V x 2 for 24V. Battery type information: Please choose your battery type before installing so you are ready for the setup. If the unit is already installed then there Non sealed lead acid or open lead acid batteries, is a slight change at the start of the instructions.
- Page 7 Unit operational mode Standby, sleep and off modes Standby - only happens when Sleep - the unit goes into sleep mode Off - to remove power in ignition mode, when the when a low input voltage threshold has from unit completely ignition is off and the input been breached.
- Page 8 Miscellaneous information unmitigated disaster as far as the auxiliary battery charging system is concerned. Battery temperature sensing: In order to increase efficiency of vehicle’s fuel Simply connect one of the enclosed temperature sensors consumption, on vehicle’s start up, the idea is to only to a battery terminal post (negative or positive) and to the charge the battery with enough power to safely restart 2x small terminals marked battery temperature.
- Page 9 Page 9...
- Page 10 Other application ideas see fig 1-4 ( previous page) battery. The charger can also transform a single output charger into a dual output. Fig 1: Most common installation, simply connect the Fig 3: This option shows a situation on many boats charger between the starter battery and the secondary or camper vehicles where there may be 3x battery (house/bow thruster) bank.
- Page 11 Temp Menu Change button Short hold = switch between H Charge Float Quick press = back light on. voltages you want to select Sterling Power Products Short hold = switch between long press switch buzzer on/off 12.2 temperatures. (temporary). In / Unit...
- Page 12 We will make the best effort to repair or replace the product, if found to be defective within the terms of the warranty. Sterling Power will ship the repaired or warranty replacement product back to the purchaser, if purchased from us in England or USA Please review the documentation included with your purchase.
Need help?
Do you have a question about the BBW1260 and is the answer not in the manual?
Questions and answers