Page 1
USER MANUAL 2kW Bathroom Downflow Fan Heater IG9041 Batch code: Please read these instructions carefully before use and retain for future reference Before switching on your appliance, always check for any damage which may have been caused in transit...
IMPORTANT SAFETY INSTRUCTIONS Read and follow all of the instructions even if you feel you are familiar with the product, and find a place to keep this manual handy for future reference. Important: This appliance is intended for use in a domestic environment only.
Page 4
• Do not use the appliance if the power cord or plug is damaged. Do not replace the power cord or any other parts yourself. • The appliance should not be used if it has been dropped or if there are visible signs of damage.
SPECIFICATION Model IG9041 Brand Igenix Wattage (W) 1800-2000W Frequency (Hz) 50/60Hz Voltage (V) 220-240V Thermostatic Cut Off Overheating Protection Pull Cord Length Approx. 50-60cm Power Settings 1000W High 2000W IP Rating IP23 Product Dimensions (mm) (H)230 x (W)125 x (D)245...
MOUNTING INSTRUCTIONS Mounting the Appliance: 1) Select a spot on the wall to mount the appliance; ensure there is a minimum of 200mm clearance either side of the unit, and at least 1.8m clearance from the bottom of the unit to the floor (fig.1) fig.1: 200mm 200mm...
Page 8
4) Loosely screw the top bracket into the top wall plug using the screw (provided) (fig.5) fig.5: 5) Hang the appliance onto the screws (fig.6) fig.6: 6) Ensure the appliance is fixed onto the top bracket, then tighten the screw to secure the unit to the wall (Fig.7) fig.7:...
Page 9
Mounting Area: This product is suitable for mounting in Zone 3 (the safe zone) of a bathroom (or similar), only if a permanent connection to the mains supply is made in accordance of the building regulations. If in doubt, consult a qualified electrician. SAFE ZONE ZONE ZONE...
OPERATING INSTRUCTIONS Once the unit has been installed correctly (following the instructions on pages 7-9): • Plug into the mains socket; the unit will be in standby mode and ‘0’ will be displayed within the power setting display. • Pull the cord downwards to select the desired power: •...
TROUBLE SHOOTING GUIDE If you experience difficulties with the appliance, please check the suggestions below before contacting customer services on 01473 271272: Problem Possible Cause Possible Solution The appliance does not The appliance is not properly Plug the appliance in firmly. work.
MAINS PLUG FUSE REPLACEMENT (Class II) Remove the central screw on the plug and open the shell. Take out the fuse and replace with a new fuse of the same Amp. Install the shell again and tighten the screws. DISPOSAL INFORMATION The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in normal unsorted...
lgenix Warranty Terms & Conditions This product is guaranteed for a period of 12 months as standard from the date of purchase against mechanical and electrical defects. You can extend your warranty for a further 12 months by registering your product. Upon registration we will cover your product for a period of 24 months from the original purchase date against any mechanical or electrical defects.
Page 15
Terms & Conditions of our warranty policy are shown on the opposite page. They are also available on our website. www.igenix.co.uk To register your product, please complete all sections of the form below and return to us at the following address: lgenix, 38 Bluestem Road, Ransomes Europark, Ipswich, IP3 9RR.
Page 16
38 Bluestem Road, Ransomes Europark, Ipswich, IP3 9RR Tel. 01473 271 272 Disclaimer: Igenix operate a policy of continual improvement and development. We therefore reserve the right to change/alter the specification and appearance of our appliances without prior notice. All diagrams and images shown in this manual are for illustration purposes only.
Need help?
Do you have a question about the IG9041 and is the answer not in the manual?
Questions and answers