Table of Contents
Advertisement
A. 1007 STANDARD EQUIPMENT - Roll Groover complete with groove
and drive rolls for 2" - 12" steel pipe, Steel/CTS Dual Guide Roll
Assembly, one and one-half horsepower electric motor drive with
foot switch. Two stage hydraulic hand pump, mounting base with
footed support legs. Complete set-up and operating instructions; 2" - 6"
rolls on tool, 8" - 12" rolls stored in box, and three depth gauges
covering the range of 2" through 12" pipe are mounted on the tool.
Shipped in closed wood crate that can be used for storage or rental
tool return.
Shipping Weight: 620 lbs.
B. OPTIONAL EQUIPMENT – (See Section IX for part numbers)
Steel Pipe:
• 2"-12" Schedule 10, 10S; 40,40S Rolls: Consisting of 2"-6" and
8"-12" roll sets.
• 14"-16" Steel Grooving Rolls (Model 1007 only)
CTS Copper System:
• 2"-8" CTS Copper System Grooving Rolls, 2"-4" CTS Depth
Gauge, and 5"-8" CTS Depth Gauge.
Other:
• Optional 230 volt, 60Hz, 15 amp, single phase electrical panel
with motor is available for the 1007 Roll Groover.
C. GROOVER CAPABILITY
Pipe Material
In.
DN(mm)
Steel
Stainless Steel
Copper
1. All wall thicknesses shown are the maximum wall thicknesses for the indicated pipe material.
2. Minimum wall thickness for each pipe material and size is:
Steel:
2" - 12" Schedule 10
Stainless Steel:
2" - 12" Schedule 10S, 40S
Copper:
2" - 2
/
1
D. Grooving Times – This chart shows approximate grooving times with the groover set-up for the proper size and groove diameter and the pipe properly
positioned on the groover. The times shown are average times from the start of rotation of the pipe in the grooving rolls to completed groove.
M
odel
2
2
⁄
1
2
50
65
0:20
0:20
*"RIDGID" is a registered trade mark of Ridgid Tool of Elyria, Ohio.
SECTION II - GROOVER DESCRIPTION
G
roover
2
2
⁄
3
1
2
50
65
80
K, L, M & DWV
" - Type M
3" - 8" - Type DWV
2
1007/3007 S
teel
Pipe Size (In./DN(mm))/Max Steel Pipe Wall Thickness
3
4
5
80
100
125
0:25
0:30
1:00
A. 3007 STANDARD EQUIPMENT – Roll Groover complete with groove
and drive rolls for 2" - 12" steel pipe, Steel/CTS Dual Guide Roll
Assembly, two stage hydraulic hand pump, mounting base with
footed support legs for direct attachment to your Ridgid* 300 Power
Drive. Complete set-up and operating instructions; 2" - 6" rolls on
tool; 8" - 12" rolls stored in box, and three depth gauges covering
the range of 2"-12" pipe are mounted on the tool. Required Ridgid
300 Power Drive not included.
Shipped in closed wood crate that can be used for storage or rental
tool return.
Shipping Weight: 330 lbs.
C
apability
Pipe Size/Wall Thickness (Schedule)
4
5
6
100
125
150
Schedule 10, 40
Schedule 10S, 40S
P
G
T
(Minutes: Seconds)
ipe
rooving
imes
6
8
150
200
1:20
1:35
1,2
8
10
12
200
250
300
10
12
14
250
300
350
1:50
2:20
2:40
1007/3007 RGM-11.13
14
16
350
400
STD.
16
400
3:00
5
Advertisement
Table of Contents
