Model Coding - Liquiflo H-Series Installation Operation & Maintenance

Liquiflo Installation, Operation & Maintenance Manual
Table 5: Material Data
Component
Pump Housing
Mounting Hardware
Mounting Bracket (Pedestal)
Motor Frames (C-Face)
Bearings
Wear Plates
Gears
Base Metal
Shafts
Coating
Housing Pins (non wetted)
Bearing Pins
Retaining Rings
Keys
O-rings
Magnets
Magnetic
Inner Magnet Casing
Coupling
Outer Magnet Casing
(1)
NOTES:
Teflon is 25% glass-filled PTFE.
(2)
Metallic material will match pump housing material.
1.3

Model Coding

A 15-position Model Code is used to completely describe a specific mag-drive pump. This code is required when
ordering a new pump or a cartridge, repair kit or replacement parts for an existing pump. The table below
describes the Model Code and gives a specific example:
Table 6: Mag-Drive Pump Model Code Description & Example
Position #
1 Pump Model (Size)
2 Pump Model (Capacity)
3 Basic Material & Port Type
4 Drive Gear
5 Idler Gear
6 Wear Plates
7 Bearings
8 Outer Magnet Bore (Motor Frame)
9 Bearing Flush
10 Shaft Coating
11
O-rings
12 Retaining Rings
13
Bearing Pins
14 Magnetic Coupling
15 Containment Can
Suffix Trim Option
NOTE: See the Liquiflo Product Catalog or our Website (www.Liquiflo.com) for complete Model Coding information.
316 Stainless Steel or Alloy-C
18-8 Stainless Steel
Cast Iron, Epoxy Painted
NEMA 56C 143/145TC & 182/ 184TC; IEC 71/80/90/100/112 (B5 Flange)
Carbon-60, Teflon, PEEK or Silicon Carbide
Carbon-60, Teflon, PEEK or Silicon Carbide
316 SS, Alloy-C, PEEK, Ryton, Teflon or Carbon
316 Stainless Steel or Alloy-C
Uncoated, Ceramic Chrome Oxide or Tungsten Carbide
17-4 PH
Teflon, 316 Stainless Steel or Alloy-C
316 Stainless Steel or Alloy-C
316 Stainless Steel or Alloy-C
Teflon, Viton, EPDM, Buna-N, Kalrez or SS/PTFE Encapsulated
MCS & MCA: Ceramic
MCU, MCB, MCC & MCV: Samarium Cobalt (SmCo)
316 Stainless Steel or Alloy-C
Carbon Steel/Epoxy
Pump Model Code Example: H5FS6PEE000000US
Description
6
H&3-Series MAG-DRIVE Gear Pumps
Models H1F-H9F, 31F-39F & 311F
Materials
(1)
(1)
(1)
(2)
(2)
(2)
(2)
(2)
Code
H5
Model H5F (H5= Pump Size; F= Full Capacity
F
S 316 SS Housing and Shafts & NPT Ports
6 316 SS Drive Gear
P PEEK Idler Gear
E Carbon-60 Wear Plates
E Carbon-60 Bearings
0 5/8" (NEMA 56 C Motor Frame)
0 No Bearing Flush (Standard Housings)
0 Uncoated (Bare 316 SS Shafts)
0
Teflon Bearing Pins
0 316 SS Retaining Rings
0
Teflon Bearing Pins
U MCU (75 in-lbs) Magnetic Coupling
S Single-Wall Containment Can
No Trim Options
Selection