Troubleshooting Guide - Shark EP602 Owner's Manual

FAMILIARISEZ-VOUS AVEZ VOTRE ASPIRATEUR
TRANSFORMER VAC
22
Spécifications techniques
Tension : 120 V., 60 Hz.
Puissance : 10 amps
*Les illustrations peuvent différer du produit lui-même.
1. Poignée
2. Tube télescopique
3. Bouton de verrouillage
4. Boyau souple
5. Bouton 1 de relâche de la
coupelle
6. Poignée de la coupelle
7. Coupelle à poussière
8. Boîtier principal
9. Surveille-filtre Intelli-
Sense MC
10. Couvercle du filtre
d'échappement
11. Commutateur marche/arrêt
12. Cordon d'alimentation
13. Bouton de relâche de la
brosse à planchers
14. Brosse à planchers
15. Suceur plat
16. Brosse à épousseter
17. Bouton de relâche du tube
télescopique
18. Bouton 2 de relâche de la
coupelle
19. Relâche du crochet à
cordon
20. Raccord du boyau
21. Bandoulière (non illustrée)
22. Brosse turbo actionnée à
l'air
24
OPERATING INSTRUCTIONS
Motor Thermostat
IMPORTANT
: This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
TROUBLE SHOOTING GUIDE
PROBLEM POSSIBLE REASON
1. Power cord not firmly plugged into
outlet.
VACUUM WILL
2. No power in wall outlet.
NOT OPERATE
3. Needs servicing.
4. Thermostat has tripped.
1. Dust cup is full.
VACUUM WILL
2. Unit clogged.
NOT PICK-UP OR
3. HEPA Filter needs cleaning or
SUCTION POWER
replacing.
IS WEAK
4. Debris screen needs cleaning.
5. Filters need cleaning
1. Dust cup is full.
TURBO BRUSH
2. Rotating brush or elbow is
DOES NOT
obstructed.
ROTATE OR
3. Belt is broken.
ROTATES
4. Hose obstructed.
SLOWLY
5. Debris screen is clogged.
6. Filters need cleaning.
DUST ESCAPING
1. Dust cup is full.
FROM VACUUM
2. Dust Cup is not installed correctly.
VACUUM, HOSE
1. Hose clogged.
OR BRUSHES
2. Dust cup is full.
WILL NOT PICK-UP
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1-800-798-7398.
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker. Replace
fuse/reset breaker.
3. Call 1-800-798-7398.
4. Turn the unit off and unplug from
outlet. Allow unit to cool down,
then restart.
1. Empty and clean dust cup.
2. Turn unit off and unplug from
wall outlet. Remove Dust Cup
Filter and check for object(s) in
air duct and remove.
3. Clean or replace HEPA Filter.
4. Clean debris screen.
5. Clean Filters
1. Empty dust cup.
2. Clear obstructions.
3. Call 1-800-798-7398.
4. Clear obstruction.
5. Clean debris screen.
6. Clean All filters.
1. Empty and clean dust cup.
2. Review Dust Cup instructions.
1. Remove hose and/or brushes.
Remove obstruction from hose
and /or brush.
2. Empty and clean dust cup.
9