Table of Contents
Advertisement
Available languages
Available languages
English
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack in an air temperature below +40 °F
(+4.5 °C), or above +104 °F (+40 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
10
COMPONENTS (FIG. A)
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.
INTENDED USE
Your BLACK+DECKER chain saw is ideal for residential
pruning applications and cutting logs up to 8" (203 mm)
in diameter.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY
Installing the Guide Bar and Saw Chain
(Fig. A, B–D, E)
CAUTION: Sharp chain. Always wear protective
gloves when handling the chain. The chain is sharp
and can cut you when it is not running.
WARNING: Sharp moving chain. To prevent
accidental operation, ensure that battery is removed
from the tool before performing the following
operations. Failure to do this could result in serious
personal injury.
If the saw chain
14
and guide bar
separately in the carton, the chain has to be attached to the
bar, and both must be attached to the body of the tool.
•
Place the saw on a flat, firm surface.
•
Rotate the bar adjust locking knob
as shown in Figure B to remove sprocket cover
•
Wearing protective gloves, grasp the saw chain
wrap it around the guide bar
facing the correct direction (see figure H)
•
Ensure the chain is properly set in the slot around the
entire guide bar.
•
Place the saw chain around the sprocket
lining up the slot on the guide bar with the bolt
the base of the tool as shown in Figure C.
•
The tensioning knob must be rotated counterclockwise
to its stop. Arrows on the sprocket cover and tensioning
knob must align before the cover is replaced. Once in
place, hold the bar still, replace sprocket cover
•
Make sure tool-free tension assembly bolt hole on the
cover lines up with the bolt
shown in Figure D.
•
Rotate the bar adjust locking knob
snug, then loosen knob one full turn, so the saw chain
can be properly tensioned.
nOTE: If the cover does not fit correctly, check that the
tab for the tool free tensioner on the bar aligns with the
slot on the inside of the sprocket cover.
•
While holding the bar adjust locking knob
the chain tensioning knob
13
are packed
16
counterclockwise
17
.
14
and
13
, ensuring the teeth are
18
while
19
17
.
19
in the main housing as
16
clockwise until
16
, rotate
20
clockwise to increase
in
Advertisement
Table of Contents
