Advertisement
SE
ADJ
TO REPLACE BELTS (See Fig. 22)
8.
RELIEVE TENSION
ON TRACTION
DRIVE BELT
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a Sears service center/department.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
The V-belts on your snowthrower are of special construction
and should be replaced by original equipment manufacturer
(OEM) belts available from your nearest Sears service
center/department.
Using other than OEM belts can cause
aersonal injury or damage to the snow thrower.
WARNING: Belt replacement
requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly,
it is important that
an assistant stand in the operating
position and hold the snow thrower
handles. Serious personal injury and/
or damage to the unit could occur if
the snow thrower
should fall during
the belt changing process.
FRAME
AUGER
ASSEMBLY
HOUSING
HANDLES
IDLER and remove traction drive belt from around
pulleys.
HINT: Insert a 3/8" drive ratchet (in the "ON" position) into
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
9.
With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
10. Install clutch rod in swing plate; secure with hairpin.
11. Place auger belt around and inside the groove of auger
pulley only.
12. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
13. Move idler arm so it does not hit impeller pulley as you
bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
become dislodged from the pulley (by catching the idler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 12. Belt
must be fully seated in pulley groove when bringing
the snow thrower together.
14. Install the two (2) hex bolts and tighten securely.
15. INSTALL ENGINE PULLEY- Place belt in pulley groove
and slide pulley on crankshaft.
Install flat washer, bolt
and tighten securely (41-47 N-m torque). Make sure
belt is inside belt keeper.
16. INSTALL BELT COVER and two (2) screws. Tighten
securely.
17. INSTALL DISCHARGE CHUTE - See "INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD" in the
Assembly / Pre-Operation section of this manual.
.
.
.
4.
5.
REMOVE GASOLINE
FROM FUEL TANK - Drain
gasoline from fuel tank into a suitable container, out-
doors, away from fire or flame. Wipe up any spilled
gasoline.
REMOVE
DISCHARGE
CHUTE - Loosen Iocknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
REMOVE BELT COVER - See "TO REMOVE BELT
COVER" in this section of this manual.
REMOVE ENGINE PULLEY- Remove bolt, flat washer
securing pulley to engine crankshaft. Remove outside
(auger) pulley only from crankshaft.
SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts holding the auger housing
and frame together.
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles
down to the ground.
6.
REMOVE HAIRPIN FROM CLUTCH ROD and re-
move clutch rod from swing plate. Tip swing plate
forward.
7.
REMOVE AUGER BELT from around pulley.
BELT KEEPER
TRACTION
DRIVE BELT
ENGINE
FLAT WASHER
PULLEY
IDLER ARM
SQUARE
HOLE
CLUTCHING
IDLER ARM
/
BRACKET
FRAME
AUGER PULLEY
BOLT
AUGER
BELT
AUGER
HOUSING
BOLTS
FIG, 22
18
Advertisement
