Advertisement
Quick Links
20____
Year of manufacture:
Contents
Electrical Drawing #:
VTX
Serial Number:
(Please log your machine's serial number and date of purchase for future reference.)
Dri-Vault
Assembly, Operating, and Maintenance Instructions
Dri-Vault VDC-253610, VDC-253624, VDC-513610
VDC-253610-DHO & VDC513610-DHO
VDC-253624
VDC-513610
Page#
2
3
4-5
6
7
8
Rev:______
Date:____/____/______
Doc. #01-14-011B
Original Instructions
VDC-253610
Vastex International, Inc.
7 Emery St
Bethlehem, Pa. 18015 USA
Phone# 610 625-2702 Fax# 610 625-2775
Web Site www.vastex.com
E-Mail info@vastex.com
Authorized Representative in Europe:
Certification Experts BV
Nieuwstad 100 1381 CE Weesp,
T he Netherlands
Tel : + 31 (0) 294 - 48 33 55
Fax : + 31 (0) 294 - 41 46 87
Vastex E-mail assistance
Purchasing & Product Info:
sales@vastex.com
Electrical Support:
stech@vastex.com
Tech Support, Mechanical Setup, and Operation
techsupport@vastex.com
Screen Printing Issues & Support:
printech@vastex.com
Advertisement
Related Manuals for VASTEX Dri-Vault VDC-253610
Summary of Contents for VASTEX Dri-Vault VDC-253610
-
Page 1: Table Of Contents
20____ Year of manufacture: Doc. #01-14-011B Original Instructions Dri-Vault Assembly, Operating, and Maintenance Instructions Dri-Vault VDC-253610, VDC-253624, VDC-513610 VDC-253610-DHO & VDC513610-DHO VDC-253610 VDC-513610 VDC-253624 Vastex International, Inc. 7 Emery St Bethlehem, Pa. 18015 USA Phone# 610 625-2702 Fax# 610 625-2775... -
Page 2: Safety And Machine Specs
VASTEX Screen Drying Cabinet is intended for the drying of emulsion on screen printing screens. Do not use for any other purpose unless authorized by Vastex International, Inc. Use of this equipment for any other purpose can be dangerous and may cause damage to this equipment voiding the warranty. -
Page 3: Assembly Instructions
Assembly 1) Unpack your drying cabinet and remove the (4) lag screws (with a 7/16 socket) holding it down to the skid. Open the doors and remove the Shelves, the Center Tree (Wide Dri-Vault only), and any oth- er items inside. 2) Slide the drying cabinet to the edge of the skid and install the (4) casters or levelers at each corner of the machine. -
Page 4: Controls
Breaker Switch is used to turn the machine on and off. In the event of a short or electrical failure, the switch will trip into the middle position. If the breaker will not reset, or it trips often, contact Vastex tech support or a li- censed electrician. - Page 5 Controls Cont. 1) Automatic Tuning has been performed at factory for all 240v machines. Automatic Tuning must be performed by the customer for the following reasons. When equipment is other than 240v (e.g. 208v), replacing a controller, replacing a “J” sensor, and/or new heating elements. Control- ler set point value must be set to 100 Degrees Fahrenheit before beginning auto-tuning.
-
Page 6: Operation, And Maintenance
The filter should be replaced as necessary. Filter material can be ordered through Vastex. 2) It is important that the inside of the dry cabinet is keep clean. Periodic cleaning of the in- side of the cabinet is recommended. -
Page 7: Troubleshooting
Check connections Customer power failed or outlet failed Check power at main disconnect Circuit breaker switch trips to center position Internal fault - contact Vastex Main Power Pilot Light lit: Temperature control knob set to “OFF” Set temperature control knob VDC-253610 &... -
Page 8: Warranty
The defective part or parts will be repaired or replaced at the discretion of Vastex International, Inc. If the equipment in question is less than one (1) year old, it will be shipped to the customer at no charge, with an RGA issued by Vastex for the defective part. The defective part must be shipped back to Vastex freight prepaid within 30 days or the account will be billed.