Norbord CSS 1610 Assembly Manual

ASSEMBLY GUIDE
*** IMPORTANT INFORMATION ***
BEFORE YOU START
Installation should be performed by a competent person
only. This product could be dangerous if incorrectly installed.
Check the pack to ensure all of the components are included.
When you are ready to start, make sure that you have all of
the correct tools to hand, have plenty of space, and that the
area for building is clean and dry.
Do not rush! Read these instructions first and run through
the sequence before you begin. Assembly should be
carried out in the steps shown in the following diagrams,
constructing one unit at a time and keeping fittings together
to avoid loss. Lay large panels on the floor using the
packaging for protection. Do not overtighten screws, as this
may damage the cabinet.
If any items are missing, or problems arise with fitting,
please call the Manufacturers' Helpline on 01769 575500.
To clean - use mild soap and water only.
Do not use abrasive cleaners.
STEP 1:
Insert into panels as shown.
A 2
Then insert and into panels as shown.
B C
IMPORTANT:
A
When fitting
Arrow points to
outside edge.
2
2
SINGLE WIDTH WALL CABINETS
HARDWARE:
15mm
8 x A 8 x
15mm J
15mm
15mm
25mm
8 x B 2 x F
8 x
C
15mm
15mm
15mm
25mm
25mm 25mm
30mm
Please use scissors to open the bag of fittings and then empty
30mm
30mm
the contents into a bowl, so that they do not get lost!
50mm
50mm 50mm
IMPORTANT: CAM FITTING AND LOCKING:
15mm
12
12
9 9 3 3
6 6
50mm
Press in A firmly. Fully insert B . Leave no gaps.
12 12
12
50mm 50mm
12
9 9 3 3
9
9 3
6 6
6
6
15mm
12 12
12 12
2 2
E
9 9 3 3 9 9 3 3
E M
6 6
6 6
E
E
15mm
15mm 15mm
1
1
Attach the LH wall hanging bracket and RH wall
M
hanging bracket to both panels , in the pre-marked
N 1
positions, using screws .
E
30mm
50mm
WALL FIXINGS:
1 x
M
50mm
15mm
30mm
1 x N
50mm
12
9
9
2 x
P
15mm
12
12
9 3
4 x
9 3 E
25mm
50mm 6
6
30mm
12 50mm
12
12 12
9 3
9 3
9 9 3 3
6
6
6 6
Turn A clockwise.
12
12
2
2
3 9 3
9 3
6
6 STEP 2:
50mm
Fit panels to panel . Tighten the cams as you go
2 1
(refer to cam fitting and locking section above).
Then carefully slide panel
4
N
15mm
4
2
1
MINIMUM TOOLS REQUIRED:
CROSS HEAD SCREWDRIVER
3 5
DRILL & DRILL BITS (3mm & 5mm)
1
12
3
3
6 6
HAMMER
12
12
9 9 3 3
SPIRIT LEVEL
6
6
2 x 1 End Panel
2 x 2 Top & Base Panel
12
12
2
2
9 3
9 3
2 x Shelf
3
6
6
1 x Back Panel
4
Turn to 2 o'clock to lock.
STEP 3:
Fit the other panel
into the grooves.
2
CSS 1610
07/15
PANELS:
2
4
3
1
3
2
to panels and tighten cams.
1 2
1
4
2
2
1