Notification When The Power Is Turned On For The First Time - Panasonic AV-HS60C4E Operating Instructions Manual

Notification when the power is turned on for the first time

Notification when the power is turned on for the first time
When using the products for the first time, connect the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4 to the <PANEL> terminal of the Main Frame
AV-HS60U1/AV-HS60U2, and then turn on the power.
Depending on the combination of the purchased Main Frame and the Control Panel, the version of the firmware for each may not match.
When the version of the firmware for the Main Frame and the Control Panel does not match, the Control Panel will not correctly boot when the power is
turned on.
Boot status when the versions do not match
Two buttons out of PST/B bus crosspoint buttons in the ME line in front will blink. One button will blink in green, and the other will blink in red. (Fig. 1)
f When it goes into this status, it is necessary to match the firmware version of the Control Panel to the Main Frame.
f If it does not go into this status and the Control Panel boots normally, the firmware versions of the Main Frame and the Control Panel do match.
f Check the latest software information and perform the version update of the software if necessary. For details, refer to "To perform the version update
of the software" (page 16).
r To match the firmware version of the Control Panel to the Main Frame
The firmware of the Control Panel is updated when the following operation is performed. Once the update is correctly performed, the firmware version of
the Control Panel will match with the firmware version of the Main Frame, and it will boot in normal status.
1
Press the button blinking in red (Fig. 1).
Update of the firmware is started.
f Status when the firmware of the Control Panel is being updated (Fig. 2)
- Eight buttons out of the PGM/A bus crosspoint buttons in the ME line in front will repeatedly blink in blue from left to right.
- Eight buttons out of the PST/B bus crosspoint buttons in the ME line in front will blink in red sequentially from left to right.
Update of the firmware will complete after approximately two minutes.
f Status when the update of the firmware of the Control Panel is completed
- Eight buttons out of the PST/B bus crosspoint buttons in the ME in front will continue to blink in red. (Fig. 3)
- Depending on the version of the firmware of the Main Frame, the Control Panel may automatically reboot. The firmware of the Control Panel is
updated correctly for this too.
2
Turn off the power of the Main Frame and the Control Panel.
f Turn off the power after completing the update of the firmware of the Control Panel.
f Do not turn off the power of the Main Frame and the Control Panel while the firmware of the Control Panel is still updating (Fig. 2).
3
Turn on the power of the Main Frame and the Control Panel.
Control Panel is booted and the menu screen is displayed in the menu panel when the firmware is correctly updated.
4
Select the <SYS> button → [MAINTENANCE] → [Boot] tab → [Initial] column → [Initial] button.
5
Select [OK] in the confirmation screen.
The AV-HS6000 is initialized.
Go on to the procedure in "To perform the version update of the software" (page 16).
r To perform the version update of the software
Check the latest software information and perform the version update of the software if necessary.
1
Check the <SYS> button → [MAINTENANCE] → [Status] tab → [System Version] column → [System Version].
16
Blue
1 2 3 4 5 6 7
Black SDI SDI SDI SDI SDI SDI
IN1 IN2 IN3 IN4 IN5 IN6
Red
Fig. 2
Green Red
Fig. 1
STILL1 OP
BUS
SHFT
4-1 4-2 4-3
8 9 10 11 12
SDI SDI SDI SDI SDI
IN7 IN8 IN9 IN10 IN11
4-4 4-5 4-6
4-7 4-8 4-9
RECALL
STORE
DEL
BUS
SHFT
CHR LIN FULL FULL
WIPE MIX MIX MIX
01s00f 01s00f 01s00f 01s00f
ME2
MIX
01s00f
CG5V CG6V
Red
Fig. 3
BUS
SHFT
CAM1 CAM2