Honeywell 8670 Quick Start Manual

Honeywell 8670 Quick Start Manual

8-bay battery charger
Hide thumbs Also See for 8670:

Advertisement

8670 8-Bay Battery Charger
Quick Start Guide
8670-8BBC-EN-QS Rev A
12/18

Advertisement

Table of Contents
loading

Summary of Contents for Honeywell 8670

  • Page 1 8670 8-Bay Battery Charger Quick Start Guide 8670-8BBC-EN-QS Rev A 12/18...
  • Page 2: Unpack Your Battery Charger

    • Make sure the items in the carton match your order. • Save the shipping container for later storage or shipping. Introduction The 8670 8-Bay Battery Charger simultaneously charges eight rechargeable lithium ion batteries. The time required for charging is dependent upon the battery internal temperature and condition.
  • Page 3: Mount The 8670 8-Bay Battery Charger

    Mount the 8670 8-Bay Battery Charger Place the charger on a horizontal, hard surface or fasten securely to a wall using the mounting holes. Mounting hardware is not supplied by Honeywell.
  • Page 4: Assemble The Power Supply

    Plug the A/C power cord into the power adapter. Plug the power cable into the power connector on the back of the 8670 8-Bay Battery Charger. Plug the A/C power cord into a grounded power source. The charger is now powered.
  • Page 5: Charge The Batteries

    Charge the Batteries Hold the battery with its three charging contacts in line with the three charging contacts in the charging pocket. Use the direc- tion of the arrow on the battery label as a guide and align the yellow dot on the battery with the yellow dot on the charger. Firmly press the battery straight down into the battery charging pocket.
  • Page 6: Interpret The Charge Pocket Leds

    When a battery is placed in a charging pocket, the battery char- ger begins charging the battery. There is a slight delay while the charger evaluates the condition of the battery before charging begins. While charging, the charger and battery will generate enough heat to feel warm.
  • Page 7 Indication Yellow/Amber continuous Battery pocket is in standby mode while warming up or cooling down. Battery is inserted incorrectly. Make sure charging terminals on battery and charger are aligned. No light on a charge pocket No battery in pocket. Battery is not fully inserted. Battery or charger is defective or damaged.
  • Page 8: Battery Charger Help

    Battery Charger Help Issue Cause Solution Battery does Different Use only Honeywell not fit in manufacturer's lithium ion batteries, charging battery. model number HNP-40, pocket in this charger. There is an Unplug charger from AC object in the supply. Remove any dirt...
  • Page 9 Issue Cause Solution Charger is Battery is not Push battery in firmly. plugged into a making contact Do not “slam” the battery live outlet, with terminals into the charging battery is in the pocket. pocket. inserted, but all Faulty battery. Replace battery.
  • Page 10 Issue Cause Solution Red LED is Current could Contact Support at flashing on any not be sourced www.honeywellaidc.com pocket through the for battery replacement battery due to options. age, exhaustion, or damage to the cell(s). The charger’s Make sure that the timeout period battery temperature is has expired.
  • Page 11 Issue Cause Solution Yellow/Amber The battery is Remove the battery from LED when too hot or too the charging pocket and battery is cold to charge. allow it to adjust to room inserted in the temperature. If the charging battery is left in the pocket charging pocket, it will cool down or warm to a...
  • Page 12: Cleaning And Storage

    Storage Remove all batteries from the charging pockets and disconnect AC power before placing the 8670 8-Bay Battery Charger in storage. It should be stored in a cool, dry place, protected from weather and airborne debris.
  • Page 13: Cautions And Warnings

    Replace it after the battery is unable to hold an adequate charge. If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection.
  • Page 14: Safety Precautions For Lithium Batteries

    Safety Precautions for Lithium Batteries • Batteries should be stored, charging contact side up, in a cool dry place, protected from weather and airborne debris, whenever possible. • Do not place batteries in fire or heat the batteries. • Do not store batteries near fire or other high temperature locations.
  • Page 15: User Documentation

    Patents For patent information, see www.hsmpats.com. Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
  • Page 16 This document contains proprietary information that is pro- tected by copyright. All rights are reserved. No part of this docu- ment may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Copyright 2016-2018 Honeywell International Inc. All rights reserved.

Table of Contents