ESAB Caddy Tig 2200i AC/DC Instruction Manual
Hide thumbs
Also See for Caddy Tig 2200i AC/DC:
- User manual ,
- Service manual (64 pages) ,
- Instruction manual (32 pages)
Related Manuals for ESAB Caddy Tig 2200i AC/DC
Summary of Contents for ESAB Caddy Tig 2200i AC/DC
- Page 1 Caddy® Tig 2200i AC/DC Instruction manual Valid for: serial no. 711-, 747-xxx-xxxx 0460 225 301 GB 20180920...
-
Page 3: Table Of Contents
Turning on the power source ..............MAINTENANCE ................... Inspection and cleaning................. TROUBLESHOOTING ................. ORDERING SPARE PARTS ................ ASSEMBLY INSTRUCTIONS ................18 DIAGRAM ......................ORDERING NUMBERS ..................21 ACCESSORIES ....................22 Rights reserved to alter specifications without notice. 0460 225 301 © ESAB AB 2018... -
Page 4: Safety
Data Sheets (SDSs). Safety precautions Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace. - Page 5 Protect your eyes and body. Use the correct welding screen and filter lens and wear protective clothing. • Protect bystanders with suitable screens or curtains. NOISE - Excessive noise can damage hearing Protect your ears. Use earmuffs or other hearing protection. 0460 225 301 - 5 - © ESAB AB 2018...
- Page 6 For further information contact the nearest ESAB dealer. ESAB has an assortment of welding accessories and personal protection equipment for purchase. For ordering information contact your local ESAB dealer or visit us on our website. 0460 225 301 - 6 -...
-
Page 7: Introduction
The Tig 2200i AC/DC is a TIG welding power source, which can also be used for MMA welding. It can be used with alternating current (AC) or direct current (DC). ESAB accessories for the product can be found in the "ACCESSORIES" chapter of this manual. -
Page 8: Technical Data
< 70 dB(A) Dimensions l×w×h 418×188×345 mm (16.46×7.40×13.58 in.) Dimensions l×w×h with cooler 418×188×496 mm (16.46×7.40×19.53 in.) Weight 15.7 kg (34.61 lbs) Weight with cooler 22.1 kg (48.72 lbs) Isolation class transformer Enclosure class IP23 0460 225 301 - 8 - © ESAB AB 2018... - Page 9 Equipment marked IP23 is intended for indoor and outdoor use. Application class The symbol indicates that the power source is designed for use in areas with increased electrical hazard. 0460 225 301 - 9 - © ESAB AB 2018...
-
Page 10: Installation
A protective earth connection must be made in accordance with regulations. Rating plate with supply connection data 0460 225 301 - 10 - © ESAB AB 2018... - Page 11 The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations. For other regions, supply cables must be suitable for the application and meet local and national regulations. 0460 225 301 - 11 - © ESAB AB 2018...
-
Page 12: Operation
General safety regulations for handling the equipment can be found in the "SAFETY" chapter of this manual. Read it through before you start using the equipment! 0460 225 301 - 12 - © ESAB AB 2018... -
Page 13: Connections And Control Devices
Connection for shielding gas Connection for welding cable or torch Key to symbols MMA TIG Return clamp 0460 225 301 - 13 - © ESAB AB 2018... -
Page 14: Connection To Cooling Unit
Whether the mains power supply is interrupted or the power unit is switched off in the normal manner, welding data will be stored so that it is available next time the unit is started. 0460 225 301 - 14 - © ESAB AB 2018... -
Page 15: Maintenance
The wear parts of the welding torch should be cleaned and replaced at regular intervals in order to achieve trouble-free wire feed. Blow the wire guide clean regularly and clean the contact tip. 0460 225 301 - 15 - © ESAB AB 2018... -
Page 16: Troubleshooting
Check that the welding current supply and return cables are correctly connected. • Check that the correct current value is set. • Check that the correct electrodes are being used. • Check the gas flow. 0460 225 301 - 16 - © ESAB AB 2018... -
Page 17: Ordering Spare Parts
Spare parts and wear parts can be ordered through your nearest ESAB dealer, see esab.com. When ordering, please state product type, serial number, designation and spare part number in accordance with the spare parts list. -
Page 18: Assembly Instructions
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS 0460 225 301 - 18 - © ESAB AB 2018... -
Page 19: Diagram
DIAGRAM DIAGRAM 0460 225 301 - 19 - © ESAB AB 2018... - Page 20 DIAGRAM 0460 225 301 - 20 - © ESAB AB 2018...
-
Page 21: Ordering Numbers
Instruction manual Control panel, Caddy® TA33 AC/DC 0460 227 Instruction manual Control panel, Caddy® TA34 AC/DC Instruction manuals and the spare parts list are available on the Internet at: www.esab.com 0460 225 301 - 21 - © ESAB AB 2018... -
Page 22: Accessories
Remote cable CAN 4 pole - 12 pole 0459 544 880 0459 554 881 10 m 0459 554 882 15 m 0459 554 883 25 m 0459 554 884 0.25 m 0460 225 301 - 22 - © ESAB AB 2018... - Page 23 0700 300 552 Tig torch TXH 201 4 m 0700 300 561 Tig torch TXH 251w 4 m 0460 315 880 Foot pedal TI Foot CAN 0460 144 880 Cooling unit CoolMini 0460 225 301 - 23 - © ESAB AB 2018...
- Page 24 For contact information visit esab.com ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone +46 (0) 31 50 90 00 http://manuals.esab.com...
Need help?
Do you have a question about the Caddy Tig 2200i AC/DC and is the answer not in the manual?
Questions and answers