Specifications - Honeywell LTE-L57V Installation Manual

Cellular communicator for the lynx touch

page of 2

/ 2
Bookmarks

Checking Signal Strength

When choosing a suitable mounting location, check the communicator's signal strength to ensure proper operation. For

most installations, using the module's internal antenna, mounting the control as high as practical, and avoiding large metal

components provides adequate signal strength for proper operation. Use the "Cell Information" screen to display signal

strength (in dBm).

Select: Security > More > Tools > [Installer Code] > Program > Comm. Diagnostics > Cell Information

Primary Site QOS Level Signal strength is displayed by a series of 1 to 5 stars (* weak to ***** strong) or "Not Present" if

there is no signal. To ensure a reliable installation at least 2 (**) stars should consistently be present.

If necessary, relocate the Control to obtain better signal strength (press Cell Information again to refresh the reading) or

install an external antenna.

Specifications

Voltage Input

Current

Idle

Transmit

Environmental

Operating

Temperature

Storage

Temperature

Humidity

Antenna

External Antenna Kit

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or

modifications could void the user's authority to operate the equipment.

FCC CLASS B STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause

interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications

in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, have a quality outdoor antenna installed.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

NDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d'Industrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet

appareil ne doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located

or operated in conjunction with any other transmitter except in accordance with FCC and ISED multi-transmitter product procedures.

Exposition aux Frequences Radio: La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm

(7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les

procédures de produit multi transmetteur FCC et ISED.

5V (provided by the control panel)

30mA, standby

490mA, max transmit

-20ºC to +55ºC (for compliance

agency: 0ºC to +49ºC)

-40ºC to +70ºC

0 to 95% relative humidity, non-

condensing (for compliance agency

0% to 85%)

• Penta-Band diversity antennas

for LTE