Table of Contents
Advertisement
Quick Links
AC-1025D Dual SIM
LTE-Fi Access Point
Quick Installation Guide
This Quick Setup Guide provides step-by-step
instructions on how to set up your LTE-Fi Access
Point. After completing the steps described in
this guide, you will be able to place the AP at
your site and provide wireless network access
to users.
PACKAGE CONTENTS
LTE-Fi Access Point
Mounting Kit
Security Plate & Cable Cover
Screw Kit
HARDWARE OVERVIEW
3D View
Power Cable
LTE & GPS Antennas
Bottom View
No
Item
1
Power
2
LED Indicators
3
Console Port
4 and 5
LTE Antennas
Side View
(Right side)-SIM 1 support Band3/8
No
Item
1
RF-45 Ethernet Port
2
USB slot
3
SIM Card Slot
4
Reset Pinhole
(Left side)-SIM 2 support Band3/28
Advertisement
Table of Contents
Related Manuals for Z-Com AC-1025D
Summary of Contents for Z-Com AC-1025D
-
Page 1: Quick Installation Guide
AC-1025D Dual SIM LTE-Fi Access Point Quick Installation Guide This Quick Setup Guide provides step-by-step instructions on how to set up your LTE-Fi Access Point. After completing the steps described in this guide, you will be able to place the AP at your site and provide wireless network access to users. -
Page 2: Setup Requirements
A wireless broadband data plan must be added to your LTE-Fi AP. The SIM must be provisioned with the carrier. Contact your carrier for details about selecting a data plan and about the process for provisioning your SIM. Item Once you have an activated SIM (Mini SIM), SIM Card Slot insert it into the SIM slot of LTE-Fi AP. -
Page 3: Step 2: Connect The Antennas
2. Attach the security plate to the LTE-Fi AP with the 4 circle mark points marked in red below facing to the SIM card/USB/Ethernet interfaces. The Ethernet and USB access holes on the security plate must be aligned with the Ethernet and USB slots on the LTE-Fi AP. -
Page 4: Mounting On A Pole
F. Hexagonal nuts x8 Brackets 4. Secure the cable cover with the M3xL8 screws (with washer). MOUNTING ON A POLE 1. Select a pole where the power is available nearby to mount the access point. You can attach the access point to any pole from 29 to 33 mm in diameter. -
Page 5: Mounting On A Flat Surface
6. Use a center punch where it is practical to dimple the pole you are going to drill. 7. Try drilling a pilot hole with a small diameter bit. If you are successful in drilling the hole without the bit slipping, and are satisfied with the results, step up to larger bits until you have a sufficiently large hole MOUNTING ON A FLAT SURFACE... -
Page 6: Step 5: Connect The Power Source
Wire Colors Description Connect to battery positive + Black Connect to battery negative - Orange Connect to ACC ignition STEP 5: CONNECT THE POWER Brown Connect to relay control line SOURCE Power Wiring Diagram CAUTION Please connect to the correct color of cable to each position, or the wrong connection will damage your AP. -
Page 7: Log Into The Ap
the wireless AP. Controller 3. From your computer, go to Start > Settings > • Configuring for Management by zCloud • Configuring for Standalone Operation Network Connections or Start > Control Panel > Network Connections. Configuring for Management by AP Controller 4. - Page 8 3. To check 3G/4G connection status, go to LTE Information. 3. To check 3G/4G connection status, go to LTE Information. Configuring for Management by zCloud Configuring for Standalone Operation Before configuring the LTE-Fi AP to be managed Before configuring fat AP Basic settings, make by zCloud, make sure that AP mode is set to Fat sure that AP mode is set to Fat AP.
-
Page 9: Step 7: Verify The Connection
Copyright © 2016 Z-Com, Inc. All rights reserved. ZWA is trademark of Z-Com, Inc. All other company and product 7. Clear the Security Profile Name and names mentioned in the documentation are held to be trademarked Wireless Network Name (SSID) box, and (and registered) by the primary holders.