Summary of Contents for Arrow Storage Products PC1010
Page 1
Owner's Manual & Assembly Instructions DC01 PATIO COVER/CARPORT Model No. PC1010 PC1010EU Attached Missing Parts, Questions on Assembly? Call: 1-800-851-1085 or assist@arrow- sheds.com Do not return to dealer, they are not equipped to handle your requests. 705220511 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE Storage Area: 99 Sq.
Page 2
BEFORE YOU BEGIN..Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your model.
Page 3
PLAN AHEAD..BO03 Watch the Weather: Be sure the day you select to install your unit is dry and calm. Do not attempt to assemble your unit on a windy day. Be careful on wet or muddy ground. Teamwork: Two or more people should work together to assemble your unit. One person can position parts or panels while the other is able to handle the fasteners and the tools.
Page 4
SAFETY FIRST..BO04 Safety precautions are important to follow throughout the construction of your patio cover/carport •Care must be taken when handling various •Practice caution with the tools being used in pieces of your unit since some contain sharp the assembly of this unit. Be familiar with the edges.
Page 5
CARE & MAINTENANCE..BO05 Finish: For long lasting nish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom.
Page 6
Foundation Recommendations BO06 The Foundation For Your Patio Cover/Carport Note: Before beginning construction, check local building codes regarding footings, location and other requirements. OPTION 1: Concrete Footings All concrete minimum 2500 P.S.I. Footing Bearing is based on soil pressures not to exceed 1,000 P.S.F.. Footing Depth to extend to below frost line but not less than 12"...
Parts List BO08 Parts in Carton One Assembly Part Part Quantity Check Key No. Number Description in Carton List 9654 Right Facia 9657 Left Facia 9664 Top Front Trim 9667 Top Left End Trim 9668 Top Right End Trim 66644 Weather Seal 3/16 x 2"...
Page 10
Parts Needed For Step 1 Rear Roof Channel 9734 Rear Roof Channel (one) 9665 Channel Brace (two) BO10 Pre-Assembly The rear roof channel assembly at- taches to the permanent structure and supports the unit. Fasten the channel braces to the end of the rear roof channel using four #10-32x7/16"...
Page 11
Parts Needed For Step 2 9661 Left Post (one) Post 9660 Right Post (one) 9652 Anchor Bracket (two) BO11 Pre-Assemblies The anchor brackets in this step will be used later to anchor the unit to the base/foundation. Position an anchor bracket inside the left &...
Page 12
Parts Needed For Step 3 Mounting Rear Roof Rear Roof Channel Assembly (one) 66627 Weather Seal BO12 Channel to Structure 1/2x 1 1/2 (13 mm x 3,8 cm) (one) 1 Positioning The height from the bottom of post to the bottom of rear roof channel is 8'-8 1/2" (265,4 cm) minimum to 9' (274,3 cm) maximum.
Page 13
Step 3 continued..BO13 3 Attaching It is important that the rear roof channel be securely anchored to a sound and at mount- ing surface. A special mounting board (2x4,2x6)x9' 11 1/8" (38 mm x 89 mm, 38 mm x 140 mm) x 302,6 cm can be used if existing surface is questionable or on mobile homes.
Page 14
Parts Needed For Step 4 9656 Roof Channel (two) Roof Channel Post Assemblies (two) 9733 Front Roof Channel (one) Assembly BO14 Get help holding post in place while attaching the roof channel. Position a roof channel, with small STEP hole 1 1/8" (2,9 cm) from end at left post, and fasten to channel brace using four #10-32x 7/16"...
Page 15
Step 4 continued..BO15 9660 Right Post STEP 9733 STEP 9660 Right Post 1 1/8" 9656 (2,9 cm)
Page 16
Step 5 Parts Needed For 9732 Front Facia (one) 9654 Right Facia (one) Facia Assembly 9657 Left Facia (one) BO16 Place front facia over front roof STEP channel with largest amount of holes on top. Fasten bottom ange with ve #10Ax 3/8"...
Page 17
Parts Needed For Step 6 Corner/Front Splice 9670 Corner Trim (four) 9669 Front Splice Trim (two) BO17 Trim If a special mounting board was used, use front splice trim pieces to cover ends of board, instead of corner trim. Fasten using two #10 screws. Position corner trim to inside corners with short flange to facia and fasten with two #10Ax3/8"...
9662 Right Roof Panel (one) Step 7 Parts Needed For 9653 Main Roof Panel (three) 9663 Left Roof Panel (one) Roof Assembly BO18 66644 Weather Seal 3/16x 2 (5 mm x 5,1 cm) (one) Attach weather stripping 3/16x2 (5 mm x 5,1 cm) to one end, on the To square unit, measure diagonally.
Page 19
Step 7 continued..BO19 Do not fasten until next step VIEW (38 mm x 89 mm) VIEW Fasten 9662 Overlapped Ribs STEP (38 mm x 89 mm) #10-32 Square Nut #10Ax3/8" (10 mm) Screw (38 mm x 89 mm) #10-32x7/16" (11 mm) Bolt #10-32x3/4"...
Page 20
Parts Needed For Step 8 Top Left and Right 9667 Top Left End Trim (one) 9668 Top Right End Trim (one) End Trim BO20 Fasten top right end trim to the outer right roof panel rib using four #10Ax3/8" (10 mm) screws. Do not fasten the bottom hole until the next step.
Page 21
Step 9 Parts Needed For 9664 Top Front Trim (one) Top Front Trim 9655 Top Trim Cap (two) BO21 Position top front trim to ends of roof panels, overlapping top left and right end trim and fasten using six #10 screws. Cover seams where trims meet at the corners with top trim caps using four screws.
Page 22
Step 10 Leveling and Anchoring Posts BO22 Check to be sure front facia and rear roof channel are still square. Level each post. Stand at one end and visually check the alignment of the post. Once all posts are aligned, mark fastener location using holes in bottom anges of anchor bracket Facia...
Page 23
Suggested Guttering System (not included) BO23 If the locality where you have installed the patio cover/carport could bene t from a guttering system, we recom- Gutter Outlet mend the following list of materials, (not included). One 10' gutter (304,8 cm) Left End Cap One downspout One outlet...
Page 24
PC1010 PC1010EU DC24 SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs 1. Avoid nicking or scraping the coating surface, when bare metal is exposed to moisture. Problem inside and out. areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective 2.